2007-2013 Highlander Kluger · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built from Aug 2013

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 Jul 2010 – Jul 2013 from Aug 2013


1. INSTALL LOWER RADIATOR SUPPORT

  1. A169445
    Install the 2 lower radiator supports.


2. INSTALL RADIATOR SUPPORT CUSHION

  1. A169438
    Install the 2 radiator support cushions.


3. INSTALL FAN ASSEMBLY WITH MOTOR

  1. A169447E01
    Put in the fan assembly with motor to the radiator assembly.

  1. Install the fan assembly with motor with the 3 bolts.

    Torque:
    7.8 N*m{ 80 kgf*cm , 69 in.*lbf }

  1. A169443
    Connect the radiator reserve tank hose or pipe to the radiator assembly.


4. INSTALL RADIATOR ASSEMBLY AND FAN ASSEMBLY WITH MOTOR

  1. A169441
    Install the radiator assembly and fan assembly with motor.


5. INSTALL COOLER CONDENSER ASSEMBLY

  1. A169439
    Install the cooler condenser assembly with the 4 bolts.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }


6. INSTALL UPPER RADIATOR SUPPORT SUB-ASSEMBLY (for LHD)

  1. A169433
    Install the upper radiator support sub-assembly with the 6 bolts and attach the hood lock control cable clamp to the radiator support.

    Torque:
    Bolt A:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

  1. A169432
    Connect the low pitched horn and high pitched horn connectors.


7. INSTALL UPPER RADIATOR SUPPORT SUB-ASSEMBLY (for RHD)

  1. A169434
    Install the upper radiator support sub-assembly with the 6 bolts and attach the hood lock control cable clamp to the radiator support.

    Torque:
    Bolt A:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

  1. A169432
    Connect the low pitched horn and high pitched horn connectors.


8. INSTALL HOOD LOCK ASSEMBLY (w/o Engine Hood Courtesy Switch)

  1. B174197
    Apply MP grease to the sliding areas of the lock.

  1. B174190
    Connect the hood lock control cable.

  1. B174189
    Install the hood lock assembly with the 3 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. B174188
    Install the hood lock nut cap.


9. INSTALL HOOD LOCK ASSEMBLY (w/ Engine Hood Courtesy Switch)

  1. B174198
    Apply MP grease to the sliding areas of the lock.

  1. B174194
    Connect the hood lock control cable.

  1. B174193
    Install the hood lock assembly with the 3 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. B174192
    Install the hood lock nut cap.

  1. B174191
    Connect the connector.


10. INSTALL RADIATOR GRILLE SUB-ASSEMBLY

  1. B258272
    Engage the 2 guides and 8 claws, and install the radiator grille sub-assembly.

  1. Install the 6 clips.


11. CONNECT COOLING FAN ECU CONNECTOR

  1. A169436
    Connect the cooling fan ECU connector and attach the wire harness clamps to the fan shroud RH side.

  1. A169435
    Attach the wire harness clamps to the fan shroud LH side.


12. CONNECT OIL COOLER HOSE

  1. A169429
    Connect the oil cooler hoses to the radiator.


13. CONNECT NO. 2 RADIATOR HOSE

  1. A169428
    Connect the No. 2 radiator hose to the radiator.


14. CONNECT NO. 1 RADIATOR HOSE

  1. A169427
    Connect the No. 1 radiator hose to the radiator.


15. INSTALL NO. 1 AIR CLEANER INLET

  1. A170454E01
    Install the No. 1 air cleaner inlet with the 2 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf } [A]

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf } [B]

  1. Connect the 2 vacuum hoses.


16. INSTALL NO. 2 AIR CLEANER INLET

  1. A170453
    Install the No. 2 air cleaner inlet with the 2 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

  1. Connect the 2 vacuum hoses and harness clamps.


17. INSTALL BATTERY

NOTICE:
When reconnected the cable, some systems need to be initialized. (Click here).

  1. A175880E02
    Install the battery tray and battery.

  1. Install the battery clamp with the bolt and nut.

    Torque:
    Bolt:
    5.4 N*m{ 55 kgf*cm , 47 in.*lbf }
    Nut A:
    5.4 N*m{ 55 kgf*cm , 47 in.*lbf }

  1. Connect the positive battery terminal, and tighten the nut.

    Torque:
    Nut B:
    6.4 N*m{ 64 kgf*cm , 57 in.*lbf }

  1. Connect the negative battery terminal, and tighten the nut.

    Torque:
    Nut C:
    6.4 N*m{ 64 kgf*cm , 57 in.*lbf }


18. INSTALL COOL AIR INTAKE DUCT SEAL

  1. A170196
    Install the cool air intake duct seal with the 11 clips.


19. ADD ENGINE COOLANT
  1. Tighten the radiator drain cock plug by hand.

  1. Tighten the cylinder block drain cock plug. (for Bank 1)

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf }

  1. Tighten the cylinder block drain cock plug. (for Bank 2, w/ Cylinder Block Drain Cock Plug)

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf }

  1. Loosen the air drain cock plug on the water inlet housing.

  1. A169415E03
    Loosen the air drain plug at the top of the radiator assembly 3 or 4 turns.
    Text in Illustration 
    *1
    Air Drain Plug

  1. Add engine coolant to the radiator inlet opening until engine coolant overflows from the engine air drain cock hole. Then tighten the air drain cock plug.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf }

  1. Continue to add engine coolant to the radiator inlet opening until engine coolant overflows from the radiator air drain hole. Then tighten the air drain plug.

    Torque:
    1.5 N*m{ 15 kgf*cm , 13 in.*lbf }

    HINT:
    If the engine coolant level at the radiator inlet opening drops after squeezing the No. 1 radiator hose and No. 2 radiator hose, add engine coolant.

  1. Slowly fill the radiator assembly with engine coolant.

    Standard Capacity:
    Condition
    Specified Condition
    w/ Rear Heater
    11.7 liters (12.4 US qts, 10.3 Imp. qts)
    w/o Rear Heater
    9.5 liters (10.1 US qts, 8.4 Imp. qts)

    NOTICE:
    Never use water as a substitute for engine coolant.

    HINT:
    TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology is a combination of low phosphates and organic acids).

  1. Slowly pour engine coolant into the radiator reservoir tank until it reaches the full line.

  1. Squeeze the No. 1 radiator hose and No. 2 radiator hose several times by hand, and then check the level of the engine coolant.
    If the engine coolant level is low, add engine coolant.

  1. Bleed air from the cooling system.

    1. Warm up the engine until the thermostat opens. While the thermostat is open, circulate the engine coolant for several minutes.

      HINT:
      The thermostat open timing can be confirmed by squeezing the No. 2 radiator hose by hand, and sensing vibrations when the engine coolant starts to flow inside the No. 2 radiator hose.

    2. Maintain the engine speed at 2500 to 3000 rpm.

    3. Squeeze the No. 1 radiator hose and No. 2 radiator hose several times by hand to bleed air.

      CAUTION:
      When squeezing the No. 1 radiator hose and No. 2 radiator hose:
      1. Wear protective gloves.
      2. Be careful as the No. 1 radiator hose and No. 2 radiator hose are hot.
      3. Keep your hands away from the fan and No. 2 fan.

      NOTICE:
      1. If the coolant temperature gauge indicates an excessive temperature, turn off the engine and let it cool.
      2. Make sure that the radiator reservoir tank still has some engine coolant in it.
      3. If the radiator reservoir tank does not have enough engine coolant, the engine may overheat or be seriously damaged.
      4. If the radiator reservoir tank does not have enough engine coolant, perform the following: 1) stop the engine, 2) wait until the engine coolant has cooled down, and 3) add engine coolant until the radiator reservoir tank is filled to the full line.

  1. Stop the engine, and wait until the engine coolant cools down.

  1. Add engine coolant to the full line on the radiator reservoir tank.


20. INSPECT FOR COOLANT LEAK

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

NOTICE:
Before performing each inspection, turn the A/C switch off.

  1. A169405
    Fill the radiator with coolant and attach a radiator cap tester.

  1. Warm up the engine.

  1. Using the radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17 psi), and check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and cylinder head.


21. INSPECT AUTOMATIC TRANSAXLE FLUID

HINT:
Click here.


22. INSPECT FOR OIL LEAK

23. INSTALL NO. 1 ENGINE UNDER COVER

  1. A237657
    Install the No. 1 engine under cover with the 6 bolts and 2 clips.


24. INSTALL ENGINE UNDER COVER ASSEMBLY

  1. A171850
    Install the engine under cover assembly with the 2 bolts, 2 screws and 5 clips.

  1. A171849
    Install the engine under cover assembly RR with the 2 bolts.


25. INSTALL V-BANK COVER SUB-ASSEMBLY

  1. A162365
    Fit the 3 retainers and install the V-bank cover.

← INSTALLATION (Jul 2010 – Jul 2013)ON-VEHICLE INSPECTION (May 2007 – Jul 2008) →