2007-2013 Highlander Kluger · Service Manual ENGINE

ON-VEHICLE INSPECTION

Inspection · Vehicles built May 2007 – Jul 2008

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010


CHECK ENGINE OIL LEVEL
  1. Warm up the engine, stop it and wait 5 minutes. The oil level should be between the dipstick's low level mark and full level mark.
    If the engine oil level is low, check for leakage and add oil up to the full level mark.

    NOTICE:
    Do not add engine oil to above the full level mark.


CHECK ENGINE OIL
  1. Check the engine oil for deterioration, water contamination, discoloring or thinning.
    If the condition is visibly poor, replace the engine oil and engine oil filter.


REMOVE FRONT WHEEL RH (for 4WD)

REMOVE ENGINE UNDER COVER ASSEMBLY (for 2WD)

  1. A171849
    Remove the 2 bolts and engine under cover assembly RR.

  1. A171850
    Remove the 2 bolts, 2 screws, 5 clips and engine under cover assembly.


DISCONNECT FRONT FENDER LINER RH (for 4WD)

REMOVE FRONT FENDER APRON SEAL RH (for 4WD)

  1. A171853
    Remove the 2 bolts, clip and front fender apron seal RH.


CHECK OIL PRESSURE

  1. A170012E01
    Disconnect the wiring harness protector. (w/ oil cooler)

  1. Disconnect the oil pressure switch assembly connector.

  1. A127994
    Using a 24 mm deep socket wrench, remove the oil pressure switch assembly. (w/o oil cooler)

  1. A170011
    Using a 24 mm deep socket wrench, remove the oil pressure switch assembly. (w/ oil cooler)

  1. A140722E02
    Install the oil pressure gauge with adapter.

  1. Warm up the engine.

  1. Check the oil pressure.

    Standard oil pressure:
    Engine Condition
    Oil Pressure
    Idle
    80 kPa (0.8 kgf/cm2, 11.6 psi) or more
    3000 rpm
    380 kPa (3.9 kgf/cm2, 55.1 psi) or more

    If the oil pressure is not as specified, check the oil pump (Click here).

  1. A050082E21
    Remove the oil pressure gauge.

  1. Apply adhesive to 2 or 3 threads of the oil pressure switch assembly.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

  1. A127994
    Using a 24 mm deep socket wrench, install the oil pressure switch assembly. (w/o oil cooler)

    Torque:
    15 N*m{ 153 kgf*cm , 11 ft.*lbf }

    NOTICE:
    Do not start the engine within 1 hour after installation.

  1. A170011
    Using a 24 mm deep socket wrench, install the oil pressure switch assembly. (w/ oil cooler)

    Torque:
    15 N*m{ 153 kgf*cm , 11 ft.*lbf }

    NOTICE:
    Do not start the engine within 1 hour after installation.

  1. Connect the oil pressure switch assembly connector.

  1. A170012E01
    Connect the wiring harness protector. (w/ oil cooler)

  1. Start the engine.

  1. Check for engine oil leaks from the oil pressure switch assembly.


INSTALL FRONT FENDER APRON SEAL RH (for 4WD)

  1. A171853
    Install the front fender apron seal RH with the 2 bolts and clip.


INSTALL FRONT FENDER LINER RH (for 4WD)

INSTALL ENGINE UNDER COVER ASSEMBLY (for 2WD)

  1. A171850
    Install the engine under cover assembly with the 2 bolts, 2 screws and 5 clips.

  1. A171849
    Install the engine under cover assembly RR with the 2 bolts.


INSTALL FRONT WHEEL RH (for 4WD)

Torque:
103 N*m{ 1050 kgf*cm , 76 ft.*lbf }

← INSTALLATION (from Aug 2013)ON-VEHICLE INSPECTION (Aug 2008 – Jun 2010) →