2007-2013 Highlander Kluger · Service Manual COMMUNICATION SYSTEM

U0230 Lost Communication with Rear Gate Module

Diagnostic trouble codes · Vehicles built Aug 2008 – Jun 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 Jul 2010 – Jun 2012 from Jul 2012

DESCRIPTION

DTC No.
Symptom
Trouble Area
U0230
No communication from back door ECU continues
  1. Power source circuit of back door ECU
  2. Back door ECU branch wire and connector
  3. Back door ECU

HINT:
For vehicles with power back door system only.


WIRING DIAGRAM

C169770E05

INSPECTION PROCEDURE

NOTICE:
  1. Turn the ignition switch off before measuring the resistances of CAN bus main wires and CAN bus branch wires.
  2. After the ignition switch is turned off, check that the key reminder warning system and light reminder warning system are not in operation.
  3. Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches, or the doors. If any doors need to be opened in order to check the connectors, open the doors and leave them open.

HINT:
  1. Operating the ignition switch, any other switches, or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
  2. Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below will help determine the cause of the malfunction.


1. CHECK FOR DTC
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Check for DTC.

    HINT:
    If the CAN MS bus communication error DTC U1002 is output, troubleshooting for U1002 and check for malfunctions in the CAN MS bus.

    Result:
    Result
    Proceed to
    DTC U1002 is not output
    A
    DTC U1002 is output
    B



B
GO TO DTC CHART (U1002) (Click here)
A


2. CHECK CAN BUS LINE FOR DISCONNECTION (BACK DOOR ECU BRANCH WIRE)
  1. Disconnect the back door ECU connector.

  1. C169769E05
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    O14-6 (MPX1) - O14-5 (MPX2)
    Ignition switch off
    54 to 69 Ω



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO POWER SLIDE DOOR ECU RH (MPX1, MPX2)
OK


3. CHECK WIRE HARNESS

  1. C169769E06
    Disconnect the back door ECU connector.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    O14-11 (GND) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    O14-12 (B) - Body ground
    Always
    10 to 14 V
    O14-8 (IG) - Body ground
    Ignition switch on (IG)
    10 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE BACK DOOR MOTOR UNIT (BACK DOOR ECU) (Click here)


← U0230 Lost Communication with Rear Gate Module (May 2007 – Jul 2008)U0230 Lost Communication with Rear Gate Module (Jul 2010 – Jun 2012) →