2007-2013 Highlander Kluger · Service Manual HEATER & AIR CONDITIONING SYSTEM

INSTALLATION

Removal / installation · Vehicles built Aug 2008 – Jun 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010


1. INSTALL REAR EVAPORATOR TEMPERATURE SENSOR

  1. E151036
    Engage the claw and clamp.

  1. Connect the 3 connectors and install the rear evaporator temperature sensor.


2. INSTALL REAR NO. 5 AIR DUCT

  1. E149737
    Install the rear No. 5 air duct with the 2 clips.


3. INSTALL NO. 1 COOLER AIR DUCT

  1. E149735E01
    Install the No. 1 cooler air duct as shown in the illustration.


4. INSTALL COOLER PLATE

  1. E149734
    Engage the 2 claws and install the cooler plate.


5. INSTALL ROOF SIDE INNER GARNISH ASSEMBLY RH

HINT:
Use the same procedure for the RH side and the LH side.


6. INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH
  1. Engage the 4 clips and the 7 claws.

  1. Install the 2 clips.

  1. Install the deck trim side panel assembly RH with the 3 bolts.

    B173622


7. INSTALL FRONT DECK SIDE TRIM COVER RH

HINT:
Use the same procedure for the RH side and the LH side.


8. INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK

HINT:
Use the same procedure for the No. 1 luggage compartment trim hook and the No. 2 deck side trim hook.


9. INSTALL ROPE HOOK ASSEMBLY (for RH Side)

HINT:
Use the same procedure for the RH side and the LH side.


10. INSTALL REAR COMBINATION LIGHT SERVICE COVER RH

  1. B173619
    Engage the 2 guides and 6 claws, and install the rear combination light service cover RH.


11. INSTALL SIDE TRIM COVER RH (for Manual Air Conditioning System)

  1. B173610
    Engage the 4 claws, and install the side trim cover RH.


12. INSTALL REAR ROOM TEMPERATURE SENSOR (for Automatic Air Conditioning System)
  1. Connect the connector.

  1. E150364
    Engage the 4 claws and install the rear room temperature sensor.


13. INSTALL DECK SIDE TRIM RH

HINT:
Use the same procedure for the RH side and the LH side.


14. INSTALL DECK SIDE TRIM COVER NO.1

HINT:
Use the same procedure for the RH side and the LH side.


15. INSTALL REAR SEAT SIDE GARNISH CAP

  1. B173617
    Engage the guide and the 6 claws.

  1. Install the rear seat side garnish cap with the screw.


16. INSTALL REAR FLOOR FINISH PLATE

  1. B173609
    Engage the 4 clips and the 4 claws, and install the rear floor finish plate.


17. INSTALL REAR NO. 2 SEAT ASSEMBLY

  1. B173781
    Install the rear No. 2 seat assembly with the 4 bolts.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }


18. CONNECT REAR SEAT LAP TYPE BELT ASSEMBLY LH

  1. B170936
    Install the rear seat lap type belt assembly LH with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    After installing the belt, check that it is not twisted.


19. CONNECT REAR SEAT LAP TYPE BELT ASSEMBLY RH
  1. Install the rear seat lap type belt assembly RH with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    After installing the belt, check that it is not twisted.


20. INSTALL REAR NO. 2 SEAT INNER BELT ASSEMBLY

  1. B170935
    Install the rear No. 2 seat inner belt assembly with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not allow the anchor part of the rear No. 2 seat inner belt assembly to overlap the protruding part of the rear No. 2 seat bracket.

    HINT:
    Use the same procedure for the RH side and LH side.


21. INSTALL REAR MAT

  1. B173249
    Install the rear mat.


22. INSTALL DECK FLOOR BOARD ASSEMBLY

  1. B178560
    Install the rear deck floor board assembly with the 4 nuts and 4 bolts.


23. INSTALL DECK SIDE TRIM BOX LH

  1. Install the deck side trim box LH as shown in the illustration.

    B178555

  1. B173243E01
    Install the 2 deck side trim clips and the clip.


24. INSTALL REAR SEAT SIDE COVER LH

  1. B173607
    Engage the 2 clips and install the rear seat side cover LH.


25. INSTALL DECK SIDE TRIM BOX RH

  1. Install the deck side trim box RH as shown in the illustration.

    B178553

  1. B173247E01
    Install the 2 deck side trim clips and the clip.


26. INSTALL JACK CARRIER ASSEMBLY (for LHD)

  1. B178549
    Engage the 3 claws, and install the jack carrier assembly.


27. INSTALL JACK CARRIER ASSEMBLY (for RHD)

  1. B179786
    Engage the 3 claws, and install the jack carrier assembly.


28. INSTALL JACK ASSEMBLY (for LHD)

  1. B173245
    Install the jack assembly.


29. INSTALL JACK ASSEMBLY (for RHD)

  1. B178566
    Install the jack assembly.


30. INSTALL JACK CARRIER CUSHION (for LHD)

  1. B178550
    Install the jack carrier cushion.


31. INSTALL JACK CARRIER CUSHION (for RHD)

  1. B178551
    Install the jack carrier cushion.


32. INSTALL JACK CARRIER SUPPORT

33. INSTALL REAR SEAT SIDE COVER RH

  1. B173608
    Engage the 2 clips and install the rear seat side cover RH.


34. INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)
  1. Install the tonneau cover assembly.


35. INSTALL NO. 2 DECK BOARD SUB-ASSEMBLY

  1. B173244
    Engage the 2 guides and install the No. 2 deck board sub-assembly.


36. INSTALL NO. 3 DECK BOARD SUB-ASSEMBLY

  1. B173242
    Engage the 2 guides and install the No. 3 deck board sub-assembly.


37. INSTALL DECK BOARD ASSEMBLY

  1. B173240
    Install the deck board sub-assembly.


38. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH

  1. B173237E01
    Align the alignment mark (green) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip RH.

    NOTICE:
    After installation, check that the corners fit correctly.


39. INSTALL REAR DOOR SCUFF PLATE RH

HINT:
Use the same procedure for the RH side and the LH side.

← INSTALLATION (May 2007 – Jul 2008)INSTALLATION (from Jul 2010) →