2007-2013 Highlander Kluger · Service Manual ENGINE

P0660 Intake Manifold Tuning Valve Control Circuit / Open (Bank 1)

Diagnostic trouble codes · Vehicles built Aug 2008 – Jun 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

This circuit opens and closes the intake air control valve in response to changes in the engine load in order to increase the intake efficiency acoustic control induction system.
When the engine speed is between 0 and 4450 rpm and the throttle valve opening angle is 60°C or more, the ECM supplies current to the actuator (ON status), to close the intake air control valve. Under other conditions, the VSV is usually OFF and the intake air control valve is open.
G041080E12
DTC No.
DTC Detection Condition
Trouble Area
P0660
The following conditions are met simultaneously for 0.5 seconds or more (2 trip detection logic):
  1. Voltage of terminal acoustic control induction system of the ECM is low when the actuator is OFF
  2. The engine has been started
  1. Open or short in intake control valve circuit
  2. Surge tank (intake air control valve)
  3. ECM

WIRING DIAGRAM

A136867E25

INSPECTION PROCEDURE


1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine and turn the intelligent tester on.

  1. Select the following menu items: Power train / Engine / Active Test / Activate the VSV for Intake Control.

  1. Check if operating noise can be heard when operating the intake control valve using the intelligent tester.

    OK:
    Operating noise can be heard.



NG
Go to step 2
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)

2. CHECK INTAKE AIR CONTROL VALVE (INTAKE AIR CONTROL OPERATION)

  1. A168220E02
    Disconnect the air intake valve connector.

  1. Apply battery voltage between the terminals of the air intake valve connector.

  1. Check the air intake valve operation.

    OK:
    Operational noise can be heard.



NG
REPLACE INTAKE AIR CONTROL VALVE
OK


3. INSPECT TERMINAL VOLTAGE (INTAKE AIR CONTROL VALVE CONNECTOR)

  1. A168221E02
    Disconnect the intake air control valve connection.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    2 - Body ground
    Ignition switch on (IG)
    9 to 14 V

  1. Reconnect the intake air control valve connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (EFI NO. 3 - INTAKE AIR CONTROL VALVE)
OK


4. CHECK HARNESS AND CONNECTOR (INTAKE AIR CONTROL VALVE - ECM)

  1. A168216E02
    Disconnect the intake air control valve connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    B28-1 - B1-33 (ACIS)
    Always
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    B28-1 or B1-33 (ACIS) - B3-1 (E1)
    Always
    10 kΩ or higher

  1. Reconnect the intake air control valve connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)


← P0660 Intake Manifold Tuning Valve Control Circuit / Open (Bank 1) (May 2007 – Jul 2008)P0660 Intake Manifold Tuning Valve Control Circuit / Open (Bank 1) (from Jul 2010) →