2007-2013 Highlander Kluger · Service Manual HEATER & AIR CONDITIONING SYSTEM

B1449/49 Rear Air Outlet Damper Control Servo Motor Circuit

Diagnostic trouble codes · Vehicles built from Jul 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

The rear outlet control servo motor sends pulse signals to indicate the damper position to the air conditioning amplifier. The air conditioning amplifier activates the motor (normal or reverse) based on these signals to move the rear outlet damper to the appropriate position, which controls the air outlet modes.

HINT:
Confirm that there are no mechanical problems because this DTC can be set if either a damper link or damper is mechanically locked.
DTC No.
DTC Detection Condition
Trouble Area
B1449/49
Rear air outlet damper position does not change even if air conditioning amplifier operates rear air outlet damper control servo motor
  1. Rear air outlet control servo motor
  2. Rear air conditioning harness
  3. Wire harness between rear air conditioning harness and air conditioning amplifier
  4. Air conditioning amplifier


WIRING DIAGRAM

E127600E39

INSPECTION PROCEDURE


1. READ VALUE USING INTELLIGENT TESTER (AIR OUT PULSE-R)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the intelligent tester main switch on.

  1. Select the item below in the Data List, and read the value displayed on the intelligent tester.

    Data List / Air Conditioner: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Air Out Pulse-R
    Rear air outlet control servo motor target pulse /
    Min.: 0, Max.: 255
    Rr FACE: 83 (pulse)
    Rr B/L: 38 (pulse)
    Rr FOOT: 7 (pulse)
    -

    OK:
    The display is as specified in the normal condition column.


    Result:
    Result
    Proceed to
    NG
    A
    OK (Checking from PROBLEM SYMPTOMS TABLE)
    B
    OK (Checking from DTC)
    C



B
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

C
REPLACE AIR CONDITIONING AMPLIFIER (Click here)
A


2. CHECK HARNESS AND CONNECTOR (REAR AIR CONDITIONING HARNESS - AIR CONDITIONING AMPLIFIER)

  1. E153085E14
    Disconnect the N11 rear air conditioning harness connector.

  1. Disconnect the D34 amplifier connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    N11-2 (RBUG) - D34-21 (RBUG)
    Always
    Below 1 Ω
    N11-3 (RBUS) - D34-1 (RBUS)
    Always
    Below 1 Ω
    N11-4 (RBBU) - D34-23 (RBBU)
    Always
    Below 1 Ω
    D34-21 (RBUG) - Body ground
    Always
    10 kΩ or higher
    D34-1 (RBUS) - Body ground
    Always
    10 kΩ or higher
    D34-23 (RBBU) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. REPLACE REAR AIR OUTLET CONTROL SERVO MOTOR
  1. Replace the rear air outlet control servo motor.


NEXT


4. CHECK DTC OUTPUT
  1. Clear the DTC (Click here).

  1. Check for DTC (Click here).

    OK:
    DTC B1449/49 is not output.



NG
REPAIR OR REPLACE REAR AIR CONDITIONING HARNESS
OK

END (REAR AIR OUTLET CONTROL SERVO MOTOR IS DEFECTIVE)


← B1449/49 Rear Air Outlet Damper Control Servo Motor Circuit (Aug 2008 – Jun 2010)B1451/51 Compressor Solenoid Circuit (May 2007 – Jul 2008) →