2007-2013 Highlander Kluger · Service Manual RESTRAINTS

INSTALLATION

Removal / installation · Vehicles built May 2007 – Jul 2008

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010


1. INSTALL SEPARATE TYPE FRONT SEAT CUSHION PAD

  1. B170971
    Using hog ring pliers, install the separate type front seat cushion pad to the separate type front seat cover with 15 new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, take care to minimize wrinkles as much as possible.

  1. B170969
    Using hog ring pliers, install the separate type front seat cushion pad to the separate type front seat cover with 6 new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, take care to minimize wrinkles as much as possible.


2. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD

  1. Engage each hook.

    B170967

  1. B170972
    Install the separate type front seat cushion cover with pad with the 2 clips.

  1. B170966
    Engage the 4 hooks.

  1. B170901
    Connect the occupant detection sensor connector as shown in the illustration.

  1. B170965
    Engage the 3 clamps.

  1. Connect the connector.

  1. B170964
    w/ Front Seat Side Airbag:

    1. Engage the 4 clamps.

    2. Connect the connector.


3. INSTALL POWER SEAT SWITCH

HINT:
Use the same procedure for the RH side and the LH side (Click here).


4. INSTALL FRONT SEAT INNER BELT ASSEMBLY

  1. B170959
    Install the front seat inner belt assembly with the nut.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding part of the front seat adjuster.

  1. Connect each connector and clamp.


5. INSTALL FRONT SEAT CUSHION INNER SHIELD

  1. B170962
    Engage the guide.

  1. B170960
    Engage the 2 claws.

  1. Install the front seat cushion inner shield with the screw.


6. INSTALL FRONT SEAT CUSHION SHIELD ASSEMBLY

  1. B170956
    Engage the 2 claws.

  1. Install the front seat cushion shield assembly with the 5 screws.

  1. B170955
    Install the 2 hooks on the backside of the front seatback board sub-assembly.


7. INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB

HINT:
Use the same procedure for the RH side and the LH side (Click here).


8. INSTALL RECLINING POWER SEAT SWITCH KNOB

HINT:
Use the same procedure for the RH side and the LH side (Click here).


9. INSTALL FRONT SEAT ASSEMBLY

HINT:
Use the same procedure for the RH side and the LH side (Click here).


10. INSTALL REAR INNER SEAT TRACK COVER

HINT:
Use the same procedure for the RH side and the LH side (Click here).


11. INSTALL REAR OUTER SEAT TRACK COVER

HINT:
Use the same procedure for the RH side and the LH side (Click here).


12. INSTALL FRONT INNER SEAT TRACK COVER

HINT:
Use the same procedure for the RH side and the LH side (Click here).


13. INSTALL FRONT OUTER SEAT TRACK COVER

HINT:
Use the same procedure for the RH side and the LH side (Click here).


14. INSTALL FRONT SEAT HEADREST ASSEMBLY

15. INSPECT FRONT SEAT ASSEMBLY
  1. Inspect the power seat operation.

  1. w/ Seat Heater System:
    Check the seat heater operation.

    1. Turn the ignition switch on (IG).

    2. Turn the seat heater switch on.

    3. Wait 5 minutes or more and confirm that the seat surface becomes warm.


16. INSPECT SRS WARNING LIGHT (w/ Front Seat Side Airbag)
(Click here)
← INSPECTION (from May 2007)INSTALLATION (Aug 2008 – Jun 2010) →