INSTALLATION
Removal / installation · Vehicles built from Jul 2010
Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010
| 1.
INSTALL SEPARATE TYPE FRONT SEAT CUSHION PAD |
 |
- Using hog ring pliers, install the separate type front seat cushion pad to the separate type front seat cover with 15 new hog rings.
- NOTICE:
- Be careful not to damage the cover.
- When installing the hog rings, take care to minimize wrinkles as much as possible.
- Using hog ring pliers, install the separate type front seat cushion pad to the separate type front seat cover with 6 new hog rings.
- NOTICE:
- Be careful not to damage the cover.
- When installing the hog rings, take care to minimize wrinkles as much as possible.
| 2.
INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD |
 |
Engage each hook.


- Install the separate type front seat cushion cover with pad with the 2 clips.
- Engage the 4 hooks.
- Connect the occupant detection sensor connector as shown in the illustration.
- Engage the 3 clamps.
Connect the connector.
- w/ Front Seat Side Airbag:
Engage the 4 clamps.
Connect the connector.
| 3.
INSTALL POWER SEAT SWITCH |
 |
- HINT:
- Use the same procedure for the RH side and the LH side (Click here).
| 4.
INSTALL FRONT SEAT INNER BELT ASSEMBLY |
 |
- Install the front seat inner belt assembly with the nut.
-
Torque:
- 42 N*m{
428 kgf*cm
, 31 ft.*lbf
}
- NOTICE:
- Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding part of the front seat adjuster.
Connect each connector and clamp.
| 5.
INSTALL FRONT SEAT CUSHION INNER SHIELD |
 |
- Engage the guide.
- Engage the 2 claws.
Install the front seat cushion inner shield with the screw.
| 6.
INSTALL FRONT SEAT CUSHION SHIELD ASSEMBLY |
 |
- Engage the 2 claws.
Install the front seat cushion shield assembly with the 5 screws.
- Install the 2 hooks on the backside of the front seatback board sub-assembly.
| 7.
INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB |
 |
- HINT:
- Use the same procedure for the RH side and the LH side (Click here).
| 8.
INSTALL RECLINING POWER SEAT SWITCH KNOB |
 |
- HINT:
- Use the same procedure for the RH side and the LH side (Click here).
| 9.
INSTALL FRONT SEAT ASSEMBLY |
 |
- HINT:
- Use the same procedure for the RH side and the LH side (Click here).
| 10.
INSTALL REAR INNER SEAT TRACK COVER |
 |
- HINT:
- Use the same procedure for the RH side and the LH side (Click here).
| 11.
INSTALL REAR OUTER SEAT TRACK COVER |
 |
- HINT:
- Use the same procedure for the RH side and the LH side (Click here).
| 12.
INSTALL FRONT INNER SEAT TRACK COVER |
 |
- HINT:
- Use the same procedure for the RH side and the LH side (Click here).
| 13.
INSTALL FRONT OUTER SEAT TRACK COVER |
 |
- HINT:
- Use the same procedure for the RH side and the LH side (Click here).
| 14.
INSTALL FRONT SEAT HEADREST ASSEMBLY |
|
| 15.
INSPECT FRONT SEAT ASSEMBLY
|
 |
Inspect the power seat operation.
w/ Seat Heater System:
Check the seat heater operation.
Turn the ignition switch on (IG).
Turn the seat heater switch on.
Wait 5 minutes or more and confirm that the seat surface becomes warm.
| 16.
INSPECT SRS WARNING LIGHT (w/ Front Seat Side Airbag) |
 |
(Click here)