2007-2013 Highlander Kluger · Service Manual BODY ELECTRICAL

Microphone Circuit between Microphone and Radio Receiver

Circuit diagnosis · Vehicles built from Jul 2010

DESCRIPTION

This circuit sends the voice signal from the telephone microphone assembly to the radio receiver.
It also supplies power from the radio receiver to the telephone microphone assembly.

WIRING DIAGRAM

E213845E03

INSPECTION PROCEDURE


1. INSPECT RADIO RECEIVER

  1. E163028E40
    Disconnect the radio receiver connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    E26-3 (MACC) - Body ground
    Ignition switch ON
    4 to 6 V

    Text in Illustration 
    *a
    Component without harness connected
    (Radio Receiver)



NG
REPLACE RADIO RECEIVER (Click here)
OK


2. CHECK HARNESS AND CONNECTOR (TELEPHONE MICROPHONE ASSEMBLY - RADIO RECEIVER)
  1. Disconnect the telephone microphone assembly and radio receiver connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Q15-4 (SNS2) - E26-1 (SNS2)
    Always
    Below 1 Ω
    Q15-3 (MIC+) - E26-2 (MIN+)
    Always
    Below 1 Ω
    Q15-5 (MIC-) - E26-5 (MIN-)
    Always
    Below 1 Ω
    Q15-1 (MACC) - E26-3 (MACC)
    Always
    Below 1 Ω
    Q15-4 (SNS2) - Body ground
    Always
    10 kΩ or higher
    Q15-3 (MIC+) - Body ground
    Always
    10 kΩ or higher
    Q15-5 (MIC-) - Body ground
    Always
    10 kΩ or higher
    Q15-1 (MACC) - Body ground
    Always
    10 kΩ or higher
    E26-6 (SGND) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. INSPECT TELEPHONE MICROPHONE ASSEMBLY

  1. E213366E02
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Q15-4 (SNS2) - Q15-5 (MIC-)
    Always
    Below 1 Ω

Text in Illustration 
*a
Component without harness connected
(Telephone Microphone Assembly)


NG
REPLACE TELEPHONE MICROPHONE ASSEMBLY (Click here)
OK


4. INSPECT TELEPHONE MICROPHONE ASSEMBLY
E210118E02
  1. Reconnect the radio receiver connector.

  1. Reconnect the telephone microphone assembly connector.

  1. Turn the ignition switch to ACC.

  1. Connect an oscilloscope to terminals 3 (MIC+) and 5 (MIC-) of the telephone microphone assembly connector.

  1. Check the waveform of the telephone microphone assembly using an oscilloscope.

    Result:
    Result
    Proceed to
    A waveform synchronized with the voice input to the telephone microphone assembly is output
    A
    A waveform synchronized with the voice input to the telephone microphone is not output
    B

Text in Illustration 
*a
Component with harness connected
(Telephone Microphone Assembly)


B
REPLACE TELEPHONE MICROPHONE ASSEMBLY (Click here)
A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)


← AVC-LAN Circuit (from Jul 2010)Radio Receiver Communication Error (from Jul 2010) →