2007-2013 Highlander Kluger · Service Manual BODY ELECTRICAL

Microphone Circuit between Microphone and Navigation Receiver Assembly

Circuit diagnosis · Vehicles built from Jul 2010

DESCRIPTION

This circuit sends a microphone voice signal from the telephone microphone assembly to the navigation receiver assembly.
It also supplies power from the navigation receiver assembly to the telephone microphone assembly.

WIRING DIAGRAM

E210114E03

INSPECTION PROCEDURE


1. INSPECT NAVIGATION RECEIVER ASSEMBLY

  1. E187123E04
    Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    E2-5 (MACC) - Body ground
    Ignition switch ACC
    4 to 6 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E2-14 (SGND) - Body ground
    Always
    Below 1 Ω
    E2-13 (MIN-) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Component with harness connected
    (Navigation Receiver Assembly)



NG
REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)
OK


2. CHECK HARNESS AND CONNECTOR
  1. Disconnect the E2 navigation receiver assembly connector.

  1. Disconnect the Q15 telephone microphone assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E2-3 (SNS2) - Q15-4 (SNS2)
    Always
    Below 1 Ω
    E2-5 (MACC) - Q15-1 (MACC)
    Always
    Below 1 Ω
    E2-4 (MIN+) - Q15-3 (MIC+)
    Always
    Below 1 Ω
    E2-13 (MIN-) - Q15-5 (MIC-)
    Always
    Below 1 Ω
    E2-3 (SNS2) - Body ground
    Always
    10 kΩ or higher
    E2-5 (MACC) - Body ground
    Always
    10 kΩ or higher
    E2-4 (MIN+) - Body ground
    Always
    10 kΩ or higher
    E2-13 (MIN-) - Body ground
    Always
    10 kΩ or higher
    E2-14 (SGND) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. INSPECT TELEPHONE MICROPHONE ASSEMBLY

  1. E176581E16
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Q15-4 (SNS2) - Q15-5 (MIC-)
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Component with harness connected
    (Telephone Microphone Assembly)



NG
REPLACE TELEPHONE MICROPHONE ASSEMBLY (Click here)
OK


4. INSPECT TELEPHONE MICROPHONE ASSEMBLY
E210118E04
  1. Reconnect the E2 navigation receiver assembly connector.

  1. Reconnect the Q15 telephone microphone assembly connector.

  1. Turn the ignition switch to ACC.

  1. Connect an oscilloscope to terminals 3 (MIC+) and 5 (MIC-) of the Q15 telephone microphone assembly connector.

  1. Check the waveform of the telephone microphone assembly using the oscilloscope.

    Result:
    Result
    Proceed to
    A waveform synchronized with the voice input to the telephone microphone assembly is output
    A
    A waveform synchronized with the voice input to the telephone microphone assembly is not output
    B

Text in Illustration 
*a
Component with harness connected
(Telephone Microphone Assembly)


NG
REPLACE TELEPHONE MICROPHONE ASSEMBLY (Click here)
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)


← Mute Signal Circuit between Navigation Receiver Assembly and Multi-media Interface ECU (from Jul 2010)Navigation Receiver Assembly Power Source Circuit (from Jul 2010) →