2007-2013 Highlander Kluger · Service Manual SECURITIES

B279A Theft Deterrent System Communication Line High Fixation

Diagnostic trouble codes · Vehicles built from Jul 2010

DESCRIPTION

If the communication line (EFIO - IMI) to the ID code box (immobiliser code ECU) is stuck high (e. g. shorted to +B), the ECM stores this DTC.
DTC No.
DTC Detection Condition
Trouble Area
B279A
When the communication line (EFIO - IMI) between ECM and ID code box (immobiliser code ECU) is stuck high.
  1. Wire harness or connector
  2. ID code box (Immobiliser code ECU)
  3. ECM

WIRING DIAGRAM

B203372E44

INSPECTION PROCEDURE

NOTICE:
If the ID code box (immobiliser code ECU) is replaced, register the ECU code and ECU communication ID.


1. CHECK DTC OUTPUT
  1. Clear the DTCs (Click here).

  1. Recheck for DTCs (Click here).

    HINT:
    If any DTCs other than DTC B279A are output, troubleshoot those DTCs first.

    Result:
    Result
    Proceed to
    DTC B279A is output
    A
    DTC B279A and other DTCs are output
    B



B
GO TO DIAGNOSTIC TROUBLE CODE CHART (Click here)
A


2. CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - ECM)
  1. Disconnect the ID code box (immobiliser code ECU) connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance and voltage according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D28-6 (EFIO) - D55-14 (IMI)
    Always
    Below 1 Ω
    D28-6 (EFIO) - Body ground
    Always
    10 kΩ or higher

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    D28-6 (EFIO) - Body ground
    Always
    Below 1 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK ID CODE BOX (IMMOBILISER CODE ECU) (OUTPUT)
  1. Reconnect the ID code box (immobiliser code ECU) connector.

  1. B219130E08
    Reconnect the ECM connector.

  1. Using an oscilloscope, check the waveform.

    Waveform (Reference):
    Item
    Content
    Terminal No. (Symbol)
    D28-6 (EFIO) - D28-8 (GND)
    Tool Setting
    10 V/DIV., 100 ms./DIV.
    Condition
    Engine switch on (IG)

    OK:
    Waveform is output normally (see illustration).

    Text in Illustration 
    *1
    Component with harness connected
    (ID Code Box (Immobiliser Code ECU))
    *2
    GND
    *3
    HIGH
    *4
    LOW



NG
Go to step 4
OK

REPLACE ECM (Click here)

4. REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
  1. Replace the ID code box (immobiliser code ECU).


NEXT


5. REGISTER ECU CODE
  1. Register the ECU code.


NEXT


6. REGISTER ECU COMMUNICATION ID
  1. Register the ECU communication ID.


NEXT


7. CHECK DTC OUTPUT
  1. Clear the DTCs (Click here).

  1. Recheck for DTCs (Click here).

    OK:
    DTC B279A is not output.



NG
REPLACE ECM (Click here)
OK

END (ID CODE BOX (IMMOBILISER CODE ECU) WAS DEFECTIVE)


← B2799 Engine Immobiliser System Malfunction (from Jul 2010)B279C Theft Deterrent System Presence Detection (from Jul 2010) →