2007-2013 Highlander Kluger · Service Manual ENGINE

Cooling Fan Circuit

Circuit diagnosis · Vehicles built Aug 2008 – Jun 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

The ECM calculates an appropriate cooling fan speed based on the engine coolant temperature, air conditioning switch condition, refrigerant pressure, engine speed, and vehicle speed and sends the signals to the cooling fan ECU to regulate the cooling fan. The cooling fan ECU controls the cooling fan speed based on the duty ratio signal sent from the ECM. By basing its control on the operating conditions, the ECM can control the fan speed optimally using the cooling fan ECU, achieving both high cooling performance and quietness. The cooling fan speed is determined based on engine coolant temperature, air conditioner operating conditions, engine speed, and vehicle speed.

INSPECTION PROCEDURE


1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE COOLING FAN)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Cooling Fan.

  1. Check the operation of the cooling fan while operating it using the intelligent tester.

    OK:
    The cooling fan rotates.



NG
Go to step 2
OK

REPLACE ECM (Click here)

2. CHECK HARNESS AND CONNECTOR (ECM - COOLING FAN ECU)

  1. Disconnect the D31 connector from the ECM.A169407E02

  1. Disconnect the cooling fan ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D31-14 (RFC) - A9-2 (SI)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. INSPECT NO. 1 COOLING FAN MOTOR

  1. A159758E01
    Disconnect the No. 1 cooling fan motor connector.

  1. Connect the battery positive terminal to terminal 2 of the cooling fan connector, and connect the battery negative terminal to terminal 1 of the No. 1 cooling fan motor connector.

    OK:
    The No. 1 cooling fan rotates.



NG
REPLACE NO. 1 COOLING FAN MOTOR (Click here)
OK


4. INSPECT NO. 2 COOLING FAN MOTOR

  1. A169409E01
    Disconnect the No. 2 cooling fan motor connector.

  1. Connect the battery positive terminal to terminal 2 of the cooling fan connector, and connect the battery negative terminal to terminal 1 of the No. 2 cooling fan motor connector.

    OK:
    The No. 2 cooling fan rotates.



NG
REPLACE NO. 2 COOLING FAN MOTOR (Click here)
OK


5. CHECK COOLING FAN ECU (POWER SOURCE)

  1. A169408E03
    Disconnect the cooling fan ECU connector.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A9-3 (+B1) - A9-1 (E1)
    Ignition switch on (IG)
    11 to 14 V



NG
Go to step 6
OK

REPLACE COOLING FAN ECU (Click here)

6. CHECK HARNESS AND CONNECTOR (COOLING FAN ECU - BODY GROUND)

  1. A169408E04
    Disconnect the cooling fan ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A9-1 (E1) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7. INSPECT FAN MAIN RELAY

  1. A169410
    Remove the FAN MAIN relay from the engine room relay block and junction block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    Battery voltage is not applied between terminals 1 and 2
    10 kΩ or higher
    3 - 5
    Apply battery voltage between terminals 1 and 2
    Below 1 Ω



NG
REPLACE FAN MAIN RELAY
OK


8. CHECK HARNESS AND CONNECTOR (COOLING FAN ECU - FAN MAIN RELAY)

  1. A169411E02
    Disconnect the cooling fan ECU connector.

  1. Remove the FAN MAIN relay from the engine room relay block and junction block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A9-3 (+B1) - 5 (FAN MAIN relay)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9. CHECK HARNESS AND CONNECTOR (FAN MAIN RELAY - BODY GROUND)

  1. A169412E02
    Remove the FAN MAIN relay from the engine room relay block and junction block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    2 (FAN MAIN relay) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


10. CHECK HARNESS AND CONNECTOR (FAN MAIN RELAY - FAN MAIN FUSE)

  1. A169413E02
    Remove the FAN MAIN relay from the engine room relay block and junction block.

  1. Remove the fusible link block assembly from the engine room relay block and junction block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    3 (FAN MAIN relay) - 1 (FAN MAIN fuse)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


11. INSPECT FUSIBLE LINK BLOCK ASSEMBLY (FAN MAIN FUSE)

  1. B165197E05
    Remove the fusible link block assembly from the engine room relay block and junction block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2 (FAN MAIN fuse)
    Always
    Below 1 Ω



NG
REPLACE FUSIBLE LINK BLOCK ASSEMBLY
OK


12. CHECK FUSE (EFI MAIN)

  1. A169465E01
    Remove the EFI MAIN fuse from the engine room relay block and junction block.
    1. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      EFI MAIN fuse
      Always
      Below 1 Ω



NG
REPLACE FUSE
OK


13. CHECK HARNESS AND CONNECTOR (EFI MAIN FUSE - ENGINE ROOM JUNCTION BLOCK ASSEMBLY)
  1. Remove the EFI MAIN fuse from the engine room relay block and junction block.

  1. A169452
    Remove the engine room junction block assembly from the engine room relay block and junction block.

  1. A169466E01
    Disconnect the 2E connector from the engine room junction block assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    2 (EFI MAIN fuse) - 2E-12
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


14. CHECK HARNESS AND CONNECTOR (FAN MAIN RELAY - ENGINE ROOM JUNCTION BLOCK ASSEMBLY)
  1. Remove the FAN MAIN relay from the engine room relay block and junction block.

  1. A169452
    Remove the engine room junction block assembly from the engine room relay block and junction block.

  1. A169448E02
    Disconnect the 2E connector from the engine room junction block assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (FAN MAIN reray) - 2E-7
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


15. CHECK HARNESS AND CONNECTOR (ENGINE ROOM JUNCTION BLOCK ASSEMBLY - BODY GROUND)

  1. A169463
    Remove the engine room junction block assembly from the engine room relay block and junction block.

  1. A169467E01
    Disconnect the 2D and 2E connectors from the engine room junction block assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    2D-8 - Body ground
    Always
    Below 1 Ω
    2E-10 - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


16. CHECK HARNESS AND CONNECTOR (ECM - ENGINE ROOM JUNCTION BLOCK ASSEMBLY)
  1. Disconnect the D31 connector from the ECM.

  1. A169452
    Remove the engine room junction block assembly from the engine room relay block and junction block.

  1. Disconnect the 2E connector from the engine room junction block assembly.A169461E01

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D31-8 (MREL) - 2E-9
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


17. INSPECT ENGINE ROOM JUNCTION BLOCK ASSEMBLY (EFI RELAY)

  1. A171750
    Remove the engine room junction block assembly from the engine room relay block and junction block.

  1. A172481E01
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    2E-12 - 2E-7
    Battery voltage is not applied between terminals 2E-9 and 2E-10
    10 kΩ or higher
    2E-12 - 2E-7
    Apply battery voltage between terminals 2E-9 and 2E-10
    Below 1 Ω

    NOTICE:
    While using the battery for the inspection, do not bring the positive and negative tester probes too close to each other as a short circuit may occur.



NG
REPLACE ENGINE ROOM JUNCTION BLOCK ASSEMBLY (Click here)
OK

REPLACE ECM (Click here)


← Cooling Fan Circuit (May 2007 – Jul 2008)Cooling Fan Circuit (from Jul 2010) →