2007-2013 Highlander Kluger · Service Manual ENGINE

Cooling Fan Circuit

Circuit diagnosis · Vehicles built from Jul 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

The ECM calculates an appropriate cooling fan speed based on the engine coolant temperature, air conditioning switch condition, refrigerant pressure, engine speed and vehicle speed, and sends the signals to the cooling fan ECU to regulate the cooling fans. The cooling fan ECU controls the cooling fan speed based on the duty ratio signal sent from the ECM. By basing its control on the operating conditions, the ECM can control the fan speed optimally using the cooling fan ECU, achieving both high cooling performance and quietness. The cooling fan speed is determined based on engine coolant temperature, air conditioner operating conditions, engine speed, and vehicle speed.

WIRING DIAGRAM

Refer to System Diagram (Click here).

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.


1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE ELECTRIC COOLING FAN)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Electric Cooling Fan.

  1. Check the operation of the cooling fans while operating it using the tester.

    OK:
    Tester Operation
    Specified Condition
    ON
    Cooling fans operated
    OFF
    Cooling fans stopped

    Result:
    Result
    Proceed to
    OK
    A
    NG (Cooling fans do not operate)
    B
    NG (Cooling fans do not stop)
    C



B
Go to step 2

C
Go to step 10
A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

2. INSPECT COOLING FAN MOTOR (COOLING FAN MOTOR AND NO. 2 COOLING FAN MOTOR)

  1. A206550E02
    Disconnect the cooling fan motor and No. 2 cooling fan motor connectors.

  1. Connect a battery positive (+) lead to each terminal 2 of the cooling fan motor and No. 2 cooling fan motor connectors, and connect a battery negative (-) lead to each terminal 1 of the cooling fan motor and No. 2 cooling fan motor connectors.

    OK:
    The cooling fan motors operate.

    Result:
    Result
    Proceed to
    OK
    A
    NG (Cooling fan motor)
    B
    NG (No. 2 Cooling fan motor)
    C

  1. Reconnect the cooling fan motor connectors.



B
REPLACE COOLING FAN MOTOR (Click here)

C
REPLACE NO. 2 COOLING FAN MOTOR (Click here)
A


3. CHECK HARNESS AND CONNECTOR (COOLING FAN ECU POWER SOURCE)

  1. A169408E03
    Disconnect the cooling fan ECU connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A9-3 (+B1) - A9-1 (E1)
    Ignition switch ON
    11 to 14 V

  1. Reconnect the cooling fan ECU connector.



NG
Go to step 5
OK


4. CHECK HARNESS AND CONNECTOR (ECM - COOLING FAN ECU)

  1. A206551E03
    Disconnect the ECM connector.

  1. Disconnect the cooling fan ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    D56-6 (RFC) or A9-2 (SI) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the cooling fan ECU connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - COOLING FAN ECU)
OK

REPLACE COOLING FAN ECU (Click here)

5. CHECK HARNESS AND CONNECTOR (COOLING FAN ECU - BODY GROUND)

  1. A169408E04
    Disconnect the cooling fan ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    A9-1 (E1) - Body ground
    Always
    Below 1 Ω

  1. Reconnect the cooling fan ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (COOLING FAN ECU - BODY GROUND)
OK


6. INSPECT RELAY (FAN MAIN)

  1. A186036
    Remove the FAN MAIN relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    No battery voltage applied to terminals 1 and 2
    10 kΩ or higher
    3 - 5
    Battery voltage applied to terminals 1 and 2
    Below 1 Ω

  1. Reinstall the FAN MAIN relay.



NG
REPLACE RELAY (FAN MAIN RELAY)
OK


7. CHECK HARNESS AND CONNECTOR (FAN MAIN RELAY POWER SOURCE)

  1. A169412E03
    Remove the FAN MAIN relay from the engine room relay block.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    3 (FAN MAIN relay) - Body ground
    Always
    11 to 14 V

  1. Reinstall the FAN MAIN relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (FAN MAIN RELAY - BATTERY)
OK


8. CHECK HARNESS AND CONNECTOR (COOLING FAN ECU - FAN MAIN RELAY)

  1. A169411E03
    Remove the FAN MAIN relay from the engine room relay block.

  1. Disconnect the cooling fan ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    A9-3 (+B1) - 5 (FAN MAIN relay)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    A9-3 (+B1) or 5 (FAN MAIN relay) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the cooling fan ECU connector.

  1. Reinstall the FAN MAIN relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (COOLING FAN ECU - FAN MAIN RELAY)
OK


9. CHECK HARNESS AND CONNECTOR (FAN MAIN RELAY - BODY GROUND)

  1. A169412E03
    Remove the FAN MAIN relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    2 (FAN MAIN relay) - Body ground
    Always
    Below 1 Ω

  1. Reinstall the FAN MAIN relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (FAN MAIN RELAY - BODY GROUND)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (FAN MAIN RELAY - ENGINE ROOM JUNCTION BLOCK ASSEMBLY)

10. CHECK HARNESS AND CONNECTOR (ECM - COOLING FAN ECU)

  1. A206551E03
    Disconnect the ECM connector.

  1. Disconnect the cooling fan ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D56-6 (RFC) - A9-2 (SI)
    Always
    Below 1 Ω

  1. Reconnect the cooling fan ECU connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - COOLING FAN ECU)
OK

REPLACE COOLING FAN ECU (Click here)


← Cooling Fan Circuit (Aug 2008 – Jun 2010)REPLACEMENT (May 2007 – Jul 2008) →