2007-2013 Highlander Kluger · Service Manual COMMUNICATION SYSTEM

TERMINALS OF ECU

System information · Vehicles built from May 2007


CHECK MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

  1. Disconnect the 1D, 1F, D6, and D7 instrument panel junction block assembly connectors.
    B150879E06

  2. Measure the voltage and resistance between the wire harness side connectors and body ground.

    Terminal No. (Symbols)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    1D-10 (BECU)*1 - Body ground
    W - Body ground
    Battery power supply
    Always
    11 to 14 V
    D7-6 (AM1)*2 - Body ground
    GR - Body ground
    Battery power supply
    Always
    11 to 14 V
    D6-1 (AM2)*2 - Body ground
    G - Body ground
    Battery power supply
    Always
    11 to 14 V
    1F-10 (GND1) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω

    HINT:
    1. If the result is not as specified, there may be a malfunction on the wire harness side.
    2. *1: w/o Smart Entry and Start System
    3. *2: w/ Smart Entry and Start System

  3. Reconnect the 1D,1F, D6, and D7 instrument panel junction block assembly connectors.

  4. Measure the pulse according to the value(s) in the table below.

    Terminal No. (Symbols)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    1E-7 (LIN1)*2 - 1F-10 (GND1)
    R - W-B
    LIN Communication line
    Ignition switch on (IG)
    Pulse generation
    D8-10 (LIN2) - 1F-10 (GND1)
    P - W-B
    LIN Communication line
    Ignition switch on (IG)
    Pulse generation

    HINT:
    1. If the result is not as specified, the main body ECU (Instrument panel junction block assembly) may be malfunctioning.
    2. *2: w/ Smart Entry and Start System


CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Side)
B158006E15
  1. Disconnect the H1*1 or G10*2 motor connector.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    for LHD: 
    Terminal No. (Symbols)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    H1-2 (B) - H1-1 (E)
    SB - W-B
    Battery power supply
    Always
    11 to 14 V
    H1-1 (E) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    for RHD: 
    Terminal No. (Symbols)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    G10-2 (B) - G10-1 (E)
    SB - W-B
    Battery power supply
    Always
    11 to 14 V
    G10-1 (E) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω

    HINT:
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the H1*1 or G10*2 motor connector.

  4. Measure the pulse according to the value(s) in the table below.

    for LHD: 
    Terminal No. (Symbols)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    H1-9 (LIN) - H1-1 (E)
    P - W-B
    LIN Communication line
    Ignition switch on (IG)
    Pulse generation
    for RHD: 
    Terminal No. (Symbols)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    G10-9 (LIN) - G10-1 (E)
    P - W-B
    LIN Communication line
    Ignition switch on (IG)
    Pulse generation

    HINT:
    If the result is not as specified, the motor may be malfunctioning.


CHECK SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY) [w/ Sliding Roof]
B160074E04
  1. Disconnect the Q12 ECU connector.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbols)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    Q12-1 (B) - Q12-2 (E)
    B - W-B
    Battery power supply
    Always
    11 to 14 V
    Q12-2 (E) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω

    HINT:
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the Q12 ECU connector.

  4. Measure the pulse according to the value(s) in the table below.

    Terminal No. (Symbols)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    Q12-4 (MPX1) - Q12-2 (E)
    P - W-B
    LIN Communication line
    Ignition switch on (IG)
    Pulse generation

    HINT:
    If the result is not as specified, the ECU may be malfunctioning.


CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) [w/ Smart Entry and Start System]
B122343E12
  1. Disconnect the D36 ECU connector.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbols)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D36-1 (+B) - D36-17 (E)
    B - B
    Battery power supply
    Always
    10 to 14 V
    D36-17 (E) - Body ground
    B - Body ground
    Ground
    Always
    Below 1 Ω

    HINT:
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the D36 ECU connector.

  4. Measure the pulse according to the value(s) in the table below.

    Terminal No. (Symbols)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D36-10 (LIN) - D36-17 (E)
    L - B
    LIN Communication line
    Ignition switch on (IG)
    Pulse generation
    D36-18 (IG) - D36-17 (E)
    G - B
    Power supply
    Ignition switch on (IG)
    10 to 14 V
    D36-18 (IG) - D36-17 (E)
    G - B
    Power supply
    Ignition switch off
    Below 1 Ω

    HINT:
    If the result is not as specified, the ECU may be malfunctioning.


CHECK ID CODE BOX (IMMOBILISER CODE ECU) [w/ Smart Entry and Start System]
B113402E02
  1. Disconnect the D28 ECU connector.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbols)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D28-1 (+B) - D28-8 (GND)
    W - V
    Battery power supply
    Always
    11 to 14 V
    D28-8 (GND) - Body ground
    V - Body ground
    Ground
    Always
    Below 1 Ω

    HINT:
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the D28 ECU connector.

  4. Measure the pulse according to the value(s) in the table below.

    Terminal No. (Symbols)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D28-3 (LIN1) - D28-8 (GND)
    LG - V
    LIN Communication line
    Ignition switch on (IG)
    Pulse generation

    HINT:
    If the result is not as specified, the ECU may be malfunctioning.


CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY) [w/ Smart Entry and Start System]
B118684E11
  1. Disconnect the D10 ECU connector.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbols)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D10-1 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    D10-6 (IG2) - D10-1 (GND)
    V - W-B
    Power supply
    Ignition switch on (IG)
    10 to 14 V
    D10-6 (IG2) - D10-1 (GND)
    V - W-B
    Power supply
    Ignition switch off
    Below 1 Ω
    D10-7 (B) - D10-1 (GND)
    G - W-B
    Battery power supply
    Always
    10 to 14 V

    HINT:
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the D10 ECU connector.

  4. Measure the pulse according to the value(s) in the table below.

    Terminal No. (Symbols)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D10-5 (LIN) - D10-1 (GND)
    GR - W-B
    LIN Communication line
    Ignition switch on (IG)
    Pulse generation

    HINT:
    If the result is not as specified, the ECU may be malfunctioning.

← PROBLEM SYMPTOMS TABLE (from Jul 2010)DTC CHECK / CLEAR (from May 2007) →