2007-2013 Highlander Kluger · Service Manual HEATER & AIR CONDITIONING SYSTEM

INSTALLATION

Removal / installation · Vehicles built May 2007 – Jul 2008

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010


1. INSTALL COOLER CONDENSER ASSEMBLY

  1. E150341
    Install the cooler condenser assembly as shown in the illustration.

  1. E150340
    Install the 4 bolts.

    HINT:
    If the condenser is replaced with a new one, add compressor oil to the new condenser.

    Capacity:
    40 cc (1.4 fl.oz.)

    Compressor oil:
    ND-8 or equivalent


2. CONNECT COOLER REFRIGERANT LIQUID PIPE A
  1. Remove the attached vinyl tape from the tube and the connecting part of the cooler condenser assembly.

  1. Sufficiently apply compressor oil to a new O-ring and the fitting surface of the tube joint.

    Compressor oil:
    ND-OIL 8 or equivalent

  1. Install the O-ring on the cooler refrigerant liquid pipe A.

  1. E150339
    Install the cooler refrigerant liquid pipe A on the cooler condenser assembly with the bolt.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }


3. CONNECT DISCHARGE TUBE SUB-ASSEMBLY
  1. Remove the attached vinyl tape from the pipe and the connecting part of the cooler condenser assembly.

  1. Sufficiently apply compressor oil to a new O-ring and the fitting surface of the pipe joint.

    Compressor oil:
    ND-OIL 8 or equivalent

  1. Install the O-ring on the discharge tube sub-assembly.

  1. E150338
    Install the discharge tube sub-assembly on the cooler condenser assembly with the bolt.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }


4. INSTALL UPPER RADIATOR SUPPORT SUB-ASSEMBLY (for LHD)

  1. A169433
    Install the upper radiator support sub-assembly with the 6 bolts and attach the hood lock control cable clamp to the radiator support.

    Torque:
    Bolt A:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

  1. A169432
    Connect the low pitched horn and high pitched horn connectors.


5. INSTALL UPPER RADIATOR SUPPORT SUB-ASSEMBLY (for RHD)

  1. A169434
    Install the upper radiator support sub-assembly with the 6 bolts and attach the hood lock control cable clamp to the radiator support.

    Torque:
    Bolt A:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

  1. A169432
    Connect the low pitched horn and high pitched horn connectors.


6. INSTALL HOOD LOCK ASSEMBLY (w/o Engine Hood Courtesy Switch)

  1. B174197
    Apply MP grease to the sliding areas of the lock.

  1. B174190
    Connect the hood lock control cable.

  1. B174189
    Install the hood lock assembly with the 3 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. B174188
    Install the hood lock nut cap.


7. INSTALL HOOD LOCK ASSEMBLY (w/ Engine Hood Courtesy Switch)

  1. B174198
    Apply MP grease to the sliding areas of the lock.

  1. B174194
    Connect the hood lock control cable.

  1. B174193
    Install the hood lock assembly with the 3 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. B174192
    Install the hood lock nut cap.

  1. B174191
    Connect the connector.


8. INSTALL RADIATOR GRILLE

  1. B172748
    Engage the 4 guides and 6 claws, and install the radiator grille.

  1. B172746
    Install the 4 clips and 2 bolts.


9. INSTALL COOL AIR INTAKE DUCT SEAL

  1. B172745
    Install the cool air intake duct seal with the 11 clips.


10. CHARGE WITH REFRIGERANT
  1. Perform vacuum purging using a vacuum pump.

  1. Charge with refrigerant HFC-134a (R134a).

    E143108E02

    Standard (w/o Rear Air Conditioning System):
    550 to 650 g (19.4 to 22.9 oz.)

    Standard (w/ Rear Air Conditioning System):
    720 to 820 g (25.4 to 28.9 oz.)

    SST
    09985-20010   (09985-02010, 09985-02050, 09985-02060, 09985-02070, 09985-02080, 09985-02090, 09985-02110, 09985-02130, 09985-02140, 09985-02150)

    NOTICE:
    1. Do not turn the A/C on before charging with refrigerant. Doing so will cause the cooler compressor to work without refrigerant, resulting in overheating of the cooler compressor.
    2. Approximately 100 g (3.53 oz.) of refrigerant may need to be charged after bubbles disappear. The refrigerant amount should be checked by quantity, not with the sight glass.

    HINT:
    Ensure that sufficient refrigerant is available to recharge the system when using a refrigerant recovery unit. Refrigerant recovery units are not always able to recover 100% of the refrigerant from an A/C system.


11. WARM UP ENGINE
  1. Keep the A/C switch on for at least 2 minutes to warm up the compressor.

    NOTICE:
    Be sure to warm up the compressor when turning the A/C on after removing and installing the cooler refrigerant lines (including the compressor), to prevent damage to the compressor.


12. INSPECT FOR REFRIGERANT LEAK
  1. After recharging with refrigerant gas, inspect for refrigerant leak using a halogen leak detector.

  1. Carry out the test under the following conditions:

    1. Make sure that the ignition switch is off.
    2. Secure good ventilation (the gas leak detector may react to volatile gases which are not refrigerant, such as evaporated gasoline and exhaust gas).
    3. Repeat the test 2 or 3 times.
    4. Make sure that there is some refrigerant remaining in the refrigeration system.
      When the compressor is off: approx. 392 to 588 kPa (4 to 6 kgf/cm2, 57 to 85 psi)

  1. I042222E25
    Using a gas leak detector, inspect for refrigerant leak from the refrigerant lines.

  1. N014519E06
    Bring the gas leak detector close to the drain hose with the detector's power off, and then turn the detector on.

    HINT:
    1. After the blower motor has stopped, let the cooling unit stand for more than 15 minutes.
    2. Bring the gas leak detector sensor under the drain hose.
    3. When bringing the gas leak detector close to the drain hose, make sure that the gas leak detector does not react to volatile gases.
      If it is not possible to avoid interference from volatile gases, the vehicle should be lifted up to allow testing.

  1. If a gas leak is not detected from the drain hose, remove the blower motor from the cooling unit. Insert the gas leak detector into the unit and perform the test.

  1. Disconnect the pressure switch connector and leave it for approximately 20 minutes. Bring the gas leak detector close to the pressure switch and perform the test.

← REASSEMBLY (from May 2007)INSTALLATION (Aug 2008 – Jun 2010) →