2007-2013 Highlander Kluger · Service Manual BODY ELECTRICAL

INSTALLATION

Removal / installation · Vehicles built May 2007 – Jul 2008

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010


1. INSTALL FRONT DOOR OUTSIDE HANDLE ASSEMBLY

  1. B172956
    Insert the front end of the front door outside handle assembly into the front door outside handle frame.

  1. Insert the rear end of the front door outside handle assembly into the front door outside handle frame. Next, slide the front door outside handle assembly toward the front of the vehicle to install it.

  1. B174199
    Connect the connector.


2. INSTALL FRONT DOOR OUTSIDE HANDLE COVER (for Driver Side)

  1. B172951
    Engage the 2 claws to install the front door outside handle cover to the front door lock cylinder.

  1. B172971
    Install the front door lock cylinder.

    HINT:
    Make sure that the front door lock cylinder rod is inserted into the front door lock assembly.

  1. B172949
    Using a "TORX" socket wrench (T30), install the front door lock cylinder with the screw.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }

  1. Install the hole plug.


3. INSTALL FRONT DOOR OUTSIDE HANDLE COVER (for Front Passenger Side)

  1. B172952
    Using a "TORX" socket wrench (T30), install the front door lock cylinder with the screw.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }

  1. Install the hole plug.


4. INSTALL FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY

  1. B174204
    Install the front door rear lower frame sub-assembly with the bolt.


5. INSTALL FRONT DOOR GLASS RUN

  1. B172946
    Install the front door glass run.


6. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY

  1. B172972E01
    Insert the front door glass sub-assembly into the front door panel along the front door glass run as indicated in the order of the arrows in the illustration.

  1. B172941
    Install the front door glass sub-assembly with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. B172940
    Install the hole plug.


7. INSTALL FRONT DOOR SERVICE HOLE COVER
  1. Apply butyl tape to the front door panel.

  1. Pass the front door lock remote control cable and rear door inside the locking cable through a new front door service hole cover.

  1. B172973E01
    Attach the front door service hole cover according to the reference points on the front door panel.

    NOTICE:
    Securely install the front door service hole cover avoiding wrinkles and air bubbles.

  1. B172939
    Connect each connector.

  1. Engage the 2 clamps.


8. INSTALL FRONT DOOR INNER GLASS WEATHERSTRIP

  1. B172938
    Install the front door inner glass weatherstrip.


9. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY
  1. Connect the connector.

  1. B172935
    Connect the front door lock remote control cable and front door inside locking cable to the front door inside handle sub-assembly.

  1. Engage the 2 clamps.

  1. B172933
    Engage the front door trim board with the 5 claws on the front door inner glass weatherstrip.

  1. Engage the 9 clips.

  1. B172932E01
    Install the 2 screws <B>.

  1. Install the screw <A> and front door trim board to the front door panel.

    Torque:
    3.5 N*m{ 36 kgf*cm , 31 in.*lbf }


10. INSTALL COURTESY LIGHT ASSEMBLY
  1. Connect the connector.

  1. B172930
    Engage the claw and install the courtesy light assembly.


11. INSTALL ASSIST GRIP COVER

  1. B172925
    Engage the 4 claws and install the assist grip cover.


12. INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG

  1. B172921
    Engage the 3 claws and install the front door inside handle bezel plug.


13. INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH

  1. B172931
    Engage the clip and claw, and install the front door lower frame bracket garnish.


14. CONNECT NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

← INSPECTION (from May 2007)INSTALLATION (Aug 2008 – Jun 2010) →