2007-2013 Highlander Kluger · Service Manual ENGINE

ON-VEHICLE INSPECTION

Inspection · Vehicles built Aug 2008 – Jun 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010


INSPECT IGNITION COIL ASSEMBLY
  1. Check for DTCs (Click here).

    NOTICE:
    If any DTC is present, perform troubleshooting in accordance with the procedure for that DTC.

  1. Check that spark occurs.

    1. Remove the 6 ignition coils and 6 spark plugs (Click here).

    2. A133895
      Disconnect the 6 fuel injector connectors.

    3. Install the spark plug into the ignition coil, and then connect the ignition coil connectors (step 3).

    4. A133897
      Ground the spark plug (step 4).

    5. Check that spark occurs while the engine is being cranked (step 5).

      NOTICE:
      1. Be sure to ground the spark plugs when checking.
      2. Replace the ignition coil if it receives an impact.
      3. Do not crank the engine for more than 2 seconds.

      HINT:
      1. Repeat steps 3 - 5 for each spark plug and ignition coil.
      2. If spark does not occur, perform the following procedure for the malfunctioning cylinder.

  1. Perform the following spark test procedure.

    1. Check that the ignition coil connector is securely connected.

      Result:
      Result
      Action
      NG
      Connect securely
      OK
      Go to next step

    2. Perform a spark test.

      1. Replace the ignition coil with a known good one.
      2. Perform the spark test again.

        Result:
        Result
        Action
        NG
        Go to next step
        OK
        Replace the ignition coil

    3. Perform a spark test.

      1. Replace the spark plug with a known good one.
      2. Perform the spark test again.

        Result:
        Result
        Action
        NG
        Go to next step
        OK
        Replace the spark plug

    4. A162638E21
      Check the power supply.
      Text in Illustration 
      *1
      Front view of wire harness connector
      (to Ignition coil assembly)
      1. Turn the ignition switch to ON.
      2. Measure the voltage according to the value(s) in the table below.

        Standard Voltage:
        Tester Connection
        Condition
        Standard Voltage
        1 (+B) - 4 (GND)
        Ignition switch ON
        11 to 14 V

        Result:
        Result
        Action
        NG
        Check wiring between battery and ignition coil and check ground circuit
        OK
        Replace the ECM (Click here)

  1. Connect the 6 fuel injector connectors.

  1. Install the 6 ignition coils and 6 spark plugs (Click here).

  1. Clear the DTCs (Click here).


INSPECT SPARK PLUG

NOTICE:
  1. Never use a wire brush for cleaning.
  2. Never attempt to adjust the electrode gap on a used spark plug.

  1. I039522E10
    Check the electrode.

    1. Using a megohmmeter, measure the insulation resistance.

      Standard insulation resistance:
      10 MΩ or higher

      HINT:
      1. If the result is below 10 MΩ, clean the plug and measure the resistance again.
      2. If a megohmmeter is not available, perform the following inspection instead.

  1. Alternative inspection method:

    1. Quickly accelerate the engine to 4000 rpm 5 times.

    2. Remove the spark plugs (Click here).

    3. Visually check the spark plug.
      If the electrode is dry, the spark plug is functioning properly. If the electrode is damp, proceed to the next step.

  1. Check the spark plug for any damage to its threads and insulator. If there is damage, replace the spark plug.

    Recommended Spark Plug:
    Manufacturer
    Spark Plug Type
    DENSO
    FK20HR11

    NOTICE:
    Use only the listed spark plug or equivalent to ensure engine performance and smooth driveability.

  1. A175269E01
    Check the spark plug electrode gap.

    Electrode gap for a new spark plug (for reference):
    1.0 to 1.1 mm (0.0394 to 0.0433 in.)

    Maximum electrode gap for a used spark plug:
    1.4 mm (0.0551 in.)

    If the gap is greater than the maximum, replace the spark plug.

  1. B062019
    Clean the spark plugs.
    If the electrode has traces of wet carbon, clean the electrode with a spark plug cleaner and then dry it.

    Standard air pressure:
    588 kPa (6 kgf/cm2, 85 psi)

    Standard duration:
    20 seconds or less

    HINT:
    Only use the spark plug cleaner when the electrode is free of oil. If the electrode has traces of oil, use gasoline to clean off the oil before using the spark plug cleaner.

  1. Install the ignition coil assembly and spark plug. (Click here).

← ON-VEHICLE INSPECTION (May 2007 – Jul 2008)ON-VEHICLE INSPECTION (from Jul 2010) →