INSTALLATION
Removal / installation · Vehicles built May 2007 – Jul 2008
Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010
| 1.
INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER (w/o Seat Cushion Front Edge Adjustment Function) |
 |
- Using hog ring pliers, temporarily install the separate type front seat cushion cover with 11 new hog rings.
- NOTICE:
- Be careful not to damage the cover.
- When installing the hog rings, take care to minimize wrinkles as much as possible.
- Using hog ring pliers, install the separate type front seat cushion cover with 6 new hog rings.
- NOTICE:
- Be careful not to damage the cover.
- When installing the hog rings, take care to minimize wrinkles as much as possible.
| 2.
INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER (w/ Seat Cushion Front Edge Adjustment Function) |
 |
- Using hog ring pliers, temporarily install the separate type front seat cushion cover with 15 new hog rings.
- NOTICE:
- Be careful not to damage the cover.
- When installing the hog rings, take care to minimize wrinkles as much as possible.
- Using hog ring pliers, install the separate type front seat cushion cover with 2 new hog rings.
- NOTICE:
- Be careful not to damage the cover.
- When installing the hog rings, take care to minimize wrinkles as much as possible.
| 3.
INSTALL FRONT SEAT CUSHION COVER WITH PAD (w/o Seat Cushion Front Edge Adjustment Function)
|
 |
Temporarily install the front seat cushion cover with pad to the front seat frame assembly with adjuster.
Engage the hooks as shown in the illustration.


Install the 2 clips.
w/ Seat Heater System:
Connect the seat heater connector.
Engage each clamp of the seat heater wire harness.
- for Front Passenger Side:
w/ Occupant Classification System:
Connect the occupant detection sensor connector as shown in the illustration.
- Engage the hooks and install the front seat cushion cover with pad.
Engage the 2 clamps.
| 4.
INSTALL FRONT SEAT CUSHION COVER WITH PAD (w/ Seat Cushion Front Edge Adjustment Function)
|
 |
Temporarily install the front seat cushion cover with pad to the front seat frame assembly with adjuster.
- Using hog ring pliers, install 4 new hog rings.
- NOTICE:
- Be careful not to damage the cover.
- When installing the hog rings, take care to minimize wrinkles as much as possible.
- Engage the hook as shown in the illustration.
Engage the hooks as shown in the illustration.


Install the 2 clips.
- Connect the 2 connectors.
Engage the hooks.
Engage the 4 clamps and install the front seat cushion cover with pad.
| 5.
INSTALL FRONT SEAT CUSHION INNER SHIELD
|
 |
- Engage the guide and temporarily install the front seat cushion inner shield as shown in the illustration.
- Engage the claw.
Install the front seat cushion inner shield with the screw.
| 6.
INSTALL FRONT SEAT INNER BELT ASSEMBLY
|
 |
- Install the front seat inner belt assembly with the nut.
-
Torque:
- 42 N*m{
428 kgf*cm
, 31 ft.*lbf
}
- NOTICE:
- Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding part of the front seat adjuster.
Connect each connector and clamp.
| 7.
INSTALL FRONT SEAT CUSHION SHIELD ASSEMBLY
|
 |
w/o Seat Cushion Front Edge Adjustment Function:
Connect the connector to the front power seat lumbar switch.
w/ Seat Cushion Front Edge Adjustment Function:
Engage the each clamps.
Connect the connector to the front power seat lumbar switch and the seat variable cushion switch.
- Engage the guide and the claw.
Install the front seat cushion shield assembly with the 5 screws.
- Engage the hooks.
| 8.
INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB
|
 |
- Engage the 4 claws and install the slide and vertical power seat switch knob.
| 9.
INSTALL RECLINING POWER SEAT SWITCH KNOB
|
 |
- Engage the 2 claws and install the reclining power seat switch knob.
| 10.
INSTALL FRONT SEAT ASSEMBLY
|
 |
Place the front seat assembly in the cabin.
- NOTICE:
- Be careful not to damage the vehicle body.
Connect the connectors under the seat.
Connect the cable to the negative (-) battery terminal.
- NOTICE:
- When reconnected the cable, some systems need to be initialized (Click here).
Temporarily install the front seat assembly with the 4 bolts.
Operate the power seat switch knob and move the seat to the rearmost position.
- Tighten the 2 bolts on the front side of the seat.
-
Torque:
- 37 N*m{
377 kgf*cm
, 27 ft.*lbf
}
- HINT:
- Tighten the bolts in the order indicated in the illustration.
Operate the power seat switch knob and move the seat to the foremost position.
- Tighten the 2 bolts on the rear side of the seat.
-
Torque:
- 37 N*m{
377 kgf*cm
, 27 ft.*lbf
}
- HINT:
- Tighten the bolts in the order indicated in the illustration.
| 11.
INSTALL REAR INNER SEAT TRACK COVER
|
 |
- Engage the 2 claws and install the rear inner seat track cover.
| 12.
INSTALL REAR OUTER SEAT TRACK COVER
|
 |
- Engage the 2 claws and install the rear outer seat track cover.
| 13.
INSTALL FRONT INNER SEAT TRACK COVER
|
 |
Operate the power seat switch knob and move the seat to the rearmost position.
- Engage the 2 claws and install the front inner seat track cover.
| 14.
INSTALL FRONT OUTER SEAT TRACK COVER
|
 |
- Engage the 2 claws and install the front outer seat track cover.
| 15.
INSTALL FRONT SEAT HEADREST ASSEMBLY |
|
| 16.
INSPECT FRONT SEAT ASSEMBLY
|
 |
Inspect the power seat operation.
w/ Seat Heater System:
Check the seat heater operation.
Turn the ignition switch on (IG).
Turn the seat heater switch on.
Wait 5 minutes or more and confirm that the seat surface becomes warm.
| 17.
INSPECT SRS WARNING LIGHT |
 |
(Click here)