2007-2013 Highlander Kluger · Service Manual BODY ELECTRICAL

INSTALLATION

Removal / installation · Vehicles built from May 2007


1. INSTALL WINDSHIELD WIPER MOTOR ASSEMBLY (for LHD)

  1. E150153
    Install the windshield wiper motor assembly with the 3 bolts.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

  1. Engage the clamp.

  1. E150152E01
    Align the matchmarks and install the crank arm assembly with the nut.

    Torque:
    17 N*m{ 173 kgf*cm , 13 ft.*lbf }

  1. E150154E01
    Apply MP grease to the crank arm pivot of the windshield wiper motor assembly.

  1. E150193
    Connect the rod of the windshield wiper link assembly to the crank arm pivot of the windshield wiper motor assembly.


2. INSTALL WINDSHIELD WIPER MOTOR ASSEMBLY (for RHD)

  1. E151602
    Install the windshield wiper motor assembly with the 3 bolts.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

  1. E151600E01
    Align the matchmarks and install the crank arm assembly with the nut.

    Torque:
    17 N*m{ 173 kgf*cm , 13 ft.*lbf }

  1. E151601E01
    Apply MP grease to the crank arm pivot of the windshield wiper motor assembly.

  1. E151603
    Connect the rod of the windshield wiper link assembly to the crank arm pivot of the windshield wiper motor assembly.


3. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

  1. E150150
    Install the windshield wiper motor and link assembly with the 4 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

  1. Connect the connector.


4. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

  1. Engage the 20 claws.

    E150149

  1. Install the cowl top ventilator louver sub-assembly with the 2 clips.

  1. E150146
    Engage the 2 claws and connect the front fender to cowl side seal LH.

  1. E150147
    Engage the 2 claws and connect the front fender to cowl side seal RH.


5. INSTALL HOOD TO COWL TOP SEAL

  1. E150148
    Engage the 8 clips and install the hood to cowl top seal.


6. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH
  1. Operate the wiper and stop the windshield wiper motor at the automatic stop position.

  1. When reinstalling:

    1. E112237E01
      Clean the wiper arm serrations.

    2. Clean the wiper pivot serrations with a wire brush.

  1. E147125E01
    Install the front wiper arm and blade assembly RH with the nut to the position shown in the illustration.

    Torque:
    24 N*m{ 245 kgf*cm , 18 ft.*lbf }

    HINT:
    Hold the wiper arm by hand when tightening the nut.

    Area
    Measurement
    A
    25.6 mm (1.00 in.)


7. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH
  1. Operate the wiper and stop the windshield wiper motor at the automatic stop position.

  1. When reinstalling:

    1. E112237E01
      Clean the wiper arm serrations.

    2. Clean the wiper pivot serrations with a wire brush.

  1. E152618E01
    Install the front wiper arm and blade assembly LH with the nut to the position shown in the illustration.

    Torque:
    24 N*m{ 245 kgf*cm , 18 ft.*lbf }

    HINT:
    Hold the wiper arm by hand when tightening the nut.

    Area
    Measurement
    A
    31.9 mm (1.26 in.)

  1. Operate the front wipers while spraying washer fluid onto the windshield glass. Make sure that the front wipers function properly and the wipers do not come into contact with the vehicle body.

← INSPECTION (from May 2007)COMPONENTS (from May 2007) →