2007-2013 Highlander Kluger · Service Manual BODY ELECTRICAL

REMOVAL

Removal / installation · Vehicles built Aug 2008 – Jun 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010


1. REMOVE ENGINE UNDER COVER ASSEMBLY

  1. A171849
    Remove the 2 bolts and engine under cover assembly RR.

  1. A171850
    Remove the 2 bolts, 2 screws, 5 clips and engine under cover assembly.


2. REMOVE NO. 1 ENGINE UNDER COVER

  1. A171855
    Remove the 6 bolts, 2 clips and No. 1 engine under cover.


3. REMOVE COOL AIR INTAKE DUCT SEAL

  1. B172745
    Remove the 11 clips and cool air intake duct seal.


4. REMOVE RADIATOR GRILLE

  1. B172749E01
    Put protective tape around the radiator grille.

  1. B172746
    Remove the 2 bolts and 4 clips.

  1. B172747
    Disengage the 6 claws and 4 guides, and remove the radiator grille.


5. REMOVE FRONT BUMPER ASSEMBLY (w/o Fog Light)

  1. B172760E01
    Put protective tape around the front bumper assembly.

    HINT:
    Use the same procedure for the RH side and LH side.

  1. B172761E01
    Remove the screw.

    HINT:
    Use the same procedure for the RH side and LH side.

  1. Using a screwdriver, turn the pin 90 degrees and remove the pin hold clip.

    HINT:
    Use the same procedure for the RH side and LH side.

  1. B172763
    Remove the 7 screws and clip.

  1. B172764
    Disengage the 4 claws and disconnect the front bumper assembly.

    HINT:
    Use the same procedure for the RH side and LH side.

  1. Remove the front bumper assembly.


6. REMOVE FRONT BUMPER ASSEMBLY (w/ Fog Light)

  1. B172760E01
    Put protective tape around the front bumper assembly.

    HINT:
    Use the same procedure for the RH side and LH side.

  1. B172761E01
    Remove the screw.

    HINT:
    Use the same procedure for the RH side and LH side.

  1. Using a screwdriver, turn the pin 90 degrees and remove the pin hold clip.

    HINT:
    Use the same procedure for the RH side and LH side.

  1. B172763
    Remove the 7 screws and clip.

  1. B172764
    Disengage the 4 claws and disconnect the front bumper assembly.

    HINT:
    Use the same procedure for the RH side and LH side.

  1. Disconnect each fog light connector, and then remove the front bumper assembly.


7. REMOVE FRONT FENDER MOULDING SUB-ASSEMBLY RH

  1. A176043
    Remove the clip.

  1. Using a 4 mm hexagon wrench, remove the screw.

  1. A176044
    Peel off the front fender side protector and disengage the 3 clips, and then remove the front fender moulding sub-assembly RH.

  1. Remove the pad from the front fender moulding sub-assembly RH.

  1. Remove the 2 clips No. 4 from the front fender moulding sub-assembly RH.

  1. A176045
    Remove the front fender side protector from the front fender moulding sub-assembly RH.


8. REMOVE FRONT FENDER LINER RH

  1. B174753E01
    Remove the screw.

  1. Using a screwdriver, turn the pin 90 degrees and remove the pin hold clip.

  1. B174750
    Using a 4 mm hexagon wrench, remove the 2 screws.

  1. Remove the 2 grommets.

    HINT:
    The grommets need to be replaced with new ones because they will break when they are removed.

  1. B174752
    Remove the 5 clips, 7 screws and front fender liner RH.


9. DRAIN WASHER FLUID

  1. E150185
    Disconnect the washer hose from the rear washer motor and pump assembly, and drain the washer fluid.


10. REMOVE REAR WASHER MOTOR AND PUMP ASSEMBLY

  1. E150197E01
    Disconnect the connector.

  1. Remove the rear washer motor and pump assembly.

← REMOVAL (May 2007 – Jul 2008)REMOVAL (from Jul 2010) →