2007-2013 Highlander Kluger · Service Manual RESTRAINTS

REMOVAL

Removal / installation · Vehicles built from May 2007


1. REMOVE REAR CENTER SEAT ASSEMBLY

2. REMOVE REAR SEAT HEADREST ASSEMBLY

3. REMOVE REAR SEAT TRACK BRACKET COVER

  1. B173775
    Disengage the 8 claws and remove the 2 rear seat track bracket covers.


4. REMOVE REAR OUTER TRACK BRACKET COVER

  1. B173776
    Disengage the 4 claws and remove the rear outer track bracket cover.


5. REMOVE REAR INNER TRACK BRACKET COVER

  1. B173777
    Disengage the 4 claws and remove the rear inner track bracket cover.


6. REMOVE REAR SEAT LEG SIDE COVER

  1. B173779
    Disengage the 3 claws.

  1. Disengage the clip and remove the rear seat leg side cover.


7. DISCONNECT REAR NO. 1 SEAT LOCK CABLE ASSEMBLY (w/ Remote Folding Function)

  1. Pull down the adjuster's lock piece to release the lock as shown in the illustration.

    B180388E01

  1. B174594E01
    Using a screwdriver wrapped with protective tape, disengage the 2 claws as shown in the illustration.

  1. Lift up the seat track adjusting handle to the uppermost position and hold the handle in this position as shown in the illustration.

    B173770E01

  1. Using a screwdriver wrapped with protective tape, disconnect the rear No. 1 seat lock cable assembly as shown in the illustration.

  1. Using a screwdriver wrapped with protective tape, disconnect the rear seat reclining control cable as shown in the illustration.

    B180393E01

  1. Secure the rear seat reclining control cable with the carpet hole as shown in the illustration.


8. REMOVE REAR NO. 1 SEAT ASSEMBLY

  1. B173780
    Remove the 3 bolts on the rear side of the seat.

  1. B173778
    Remove the 2 bolts on the front side of the seat and the rear No. 1 seat assembly.

    NOTICE:
    Be careful not to damage the vehicle body.


9. REMOVE REAR SEAT RECLINING UPPER COVER

  1. B173783E01
    Using a screwdriver wrapped with protective tape, disengage the 3 claws and remove the rear seat reclining upper cover.


10. REMOVE NO. 1 RECLINING ADJUSTER RELEASE HANDLE

  1. B196364
    Remove the 3 screws and the No. 1 reclining adjuster release handle.


11. REMOVE REAR SEAT CUSHION MOULDING LH

  1. B196365
    Remove the screw.

  1. Disengage the 5 claws.

  1. Disengage the guide and remove the rear seat cushion moulding LH.


12. REMOVE SEAT ADJUSTER COVER CAP

  1. B173786E01
    Using a screwdriver wrapped with protective tape, disengage the 2 claws and remove the seat adjuster cover cap.


13. REMOVE REAR SEAT CUSHION MOULDING RH

  1. B173788
    Remove the screw.

  1. Disengage the 6 claws and remove the rear seat cushion moulding RH.


14. REMOVE REAR NO. 1 SEAT CUSHION COVER WITH PAD

  1. B180396
    Disengage the 2 hooks.

  1. B173795
    Disengage the 2 hooks.

  1. Remove the 2 hog rings.

  1. B196379
    Disengage the 3 buttons.

  1. B206101
    Disengage the 12 hooks.

  1. B173797
    Remove the 3 hog rings and the rear No. 1 seat cushion cover with pad.


15. REMOVE SEAT TRACK UPPER RAIL COVER

  1. B206104
    Remove the screw.

  1. Disengage the claw and remove the seat track upper rail cover.


16. REMOVE REAR SEAT RECLINING INNER COVER

  1. B206105
    Remove the screw.

  1. Disengage the guide and remove the rear seat reclining inner cover.


17. REMOVE REAR NO. 1 SEAT INNER BELT ASSEMBLY

  1. B170974
    Remove the bolt and the rear No. 1 seat inner belt assembly.

← COMPONENTS (from May 2007)INSTALLATION (from May 2007) →