2007-2013 Highlander Kluger · Service Manual BODY

INSTALLATION

Removal / installation · Vehicles built Aug 2008 – Jun 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010


1. INSTALL SLIDING ROOF WEATHERSTRIP

  1. Install the sliding roof weatherstrip as follows:

    1. Position the joint of the weatherstrip at the rear center.

    2. Align the marks on the weatherstrip with the middle marks at the corners of the sliding roof panel and install the weatherstrip.

    3. Install the lip of the weatherstrip firmly.

      B139674E02


2. INSTALL SLIDING ROOF HOUSING SUB-ASSEMBLY
  1. Install the sliding roof housing sub-assembly with the 7 nuts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. Install the 8 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }


    B173673

  1. B173668
    Engage the claw.

  1. Install the room light bracket with the nut.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. Connect the 4 sliding roof drain hoses.

    B173674E01

    NOTICE:
    Be sure to install the drain hoses properly to prevent entry of water.

  1. Connect each clamp.


3. INSTALL SLIDING ROOF GLASS SUB-ASSEMBLY

  1. Using a T25 "TORX" socket wrench, temporarily install the sliding roof glass sub-assembly with the 4 screws.

    B173667

  1. B173675E01
    Perform a level check.

    1. Check the difference in level for "a" between the roof panel and the upper surface of the weatherstrip when the sliding roof glass is fully closed.

      Standard:
      Area
      Measurement
      A - A
      0 + 1.0 mm (0 + 0.039 in.)
      0 - 2.0 mm (0 - 0.079 in.)
      B - B
      0 + 2.0 mm (0 + 0.079 in.)
      0 - 1.0 mm (0 - 0.039 in.)
      C - C
      0 + 1.5 mm (0 + 0.059 in.)
      0 - 1.5 mm (0 - 0.059 in.)
      D - D
      0 + 1.5 mm (0 + 0.059 in.)
      0 - 1.0 mm (0 - 0.039 in.)

      HINT:
      "+" represents the condition that the glass is above the panel level. "-" represents the condition that the glass is below the panel level.

  1. B173676E01
    Perform a gap check.

    1. Check the gap between the roof panel and roof glass.

      NOTICE:
      The gap must be even all around.

  1. After adjusting the sliding roof glass, using a T25 "TORX" socket wrench, install the sliding roof glass sub-assembly with the 4 screws.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }


4. INSPECT WATER LEAK
  1. After adjusting the sliding roof glass sub-assembly, inspect for water leaks.

  1. If there are any leaks, readjust the sliding roof glass sub-assembly.


5. INSTALL SLIDING ROOF SIDE GARNISH LH

  1. B160554
    Engage the 5 claws and install the sliding roof side garnish LH.


6. INSTALL SLIDING ROOF SIDE GARNISH RH

HINT:
Use the same procedure for the RH side and the LH side.


7. INSTALL CURTAIN SHIELD AIR BAG ASSEMBLY LH (w/ Curtain Shield Airbag)
  1. Check that the ignition switch is off.

  1. Check that the battery negative (-) cable is disconnected.

    CAUTION:
    Wait for at least 90 seconds after disconnecting the cable to prevent airbag deployment.

  1. Temporarily install the curtain shield airbag assembly to the body panel with the 11 hooks.

    NOTICE:
    Do not twist the curtain shield airbag assembly when installing it.

  1. Install 11 new bolts.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

    HINT:
    Tighten the bolts in the order shown in the illustration.


    C170631E01

  1. Connect the curtain shield airbag connector.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.


    C168036


8. INSTALL CURTAIN SHIELD AIR BAG ASSEMBLY RH (w/ Curtain Shield Airbag)

HINT:
Use the same procedure for the RH side and the LH side.


9. INSTALL ROOF HEADLINING ASSEMBLY

  1. B173274
    Pull the roof headlining assembly into the vehicle through the back door.

    NOTICE:
    Do not damage the roof headlining assembly or body interior.

  1. Install the 3 clips.

  1. Connect the sliding roof drive gear connector.

  1. Connect the No. 2 antenna cord sub-assembly connector to the rear pillar RH.

  1. Connect the No. 2 antenna cord sub-assembly connector and engage the 3 clamps to the front pillar RH.

  1. Install the No. 2 antenna cord sub-assembly to the front pillar RH with the bolt.

  1. w/ Rear Seat Entertainment System:

    1. Connect the No. 1 roof wire connector to the rear pillar LH.

  1. Connect the No. 1 roof wire connectors and engage the 3 clamps to the front pillar LH.

    B173269E01

    NOTICE:
    After installation, make sure that the back door weatherstrip does not interfere with the roof headlining assembly.


10. INSTALL VISOR HOLDER

  1. B151383
    Engage the 2 claws.

  1. Push in the visor holder as shown in the illustration.

    HINT:
    Use the same procedure for the RH side and the LH side.


11. INSTALL SUN ROOF OPENING TRIM MOULDING

  1. B175148E01
    Align the joining point of the moulding with the notch of the roof headlining assembly, and install the sun roof opening trim moulding.

    NOTICE:
    After installation, check that the corners fit correctly.


12. INSTALL ROOF HEADLINING TRIM CLIP STOPPER

  1. B173594
    Install the roof headlining trim clip stopper with the bolt.

  1. Engage the 3 claws.

    HINT:
    Use the same procedure for the RH side and the LH side.


13. INSTALL ASSIST GRIP ASSEMBLY

  1. B173259
    Assemble the assist grip assembly as shown in the illustration.

  1. B173260
    Install the assist grip assembly.

    HINT:
    Use the same procedure for the other 4 assist grips.


14. INSTALL TELEVISION DISPLAY ASSEMBLY (w/ Rear Seat Entertainment System)

  1. E151790
    Engage the 2 claws and the 2 clips.

  1. E150582
    Install the television display with the 4 bolts.

    HINT:
    Tighten the bolts in the order shown in the illustration.

  1. Connect the connector.


15. INSTALL TELEVISION BASE (w/ Rear Seat Entertainment System)

  1. E150581E01
    Engage the 2 guides and 4 clips and install the television base.


16. INSTALL NO. 2 ROOM LIGHT ASSEMBLY

  1. B139564
    Engage the 4 claws and install the lens cover.

  1. B139562
    Engage the 4 claws and install the room light switch base to the No. 2 room light assembly.

  1. B160475
    Engage the 4 claws and install the No. 2 room light assembly.


17. INSTALL NO. 1 ROOM LIGHT ASSEMBLY (for Standard)

  1. B139564
    Engage the 4 claws and install the lens cover.

  1. B139562
    Engage the 4 claws and install the room light switch base to the No. 1 room light assembly.

  1. B160475
    Engage the 4 claws and install the No. 1 room light assembly.


18. INSTALL NO. 1 ROOM LIGHT ASSEMBLY (for Independent Type)

  1. B173253
    Engage the 4 claws and install the lens cover.

  1. B173256
    Engage the 8 claws and install the room light switch base to the No. 1 room light assembly.

  1. B173255
    Engage the 4 claws and install the No. 1 room light assembly.


19. INSTALL INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)

  1. B175049
    Engage the 2 claws and install the inner rear view mirror stay holder cover.

  1. B175050E01
    Engage the 2 claws and install the inner rear view mirror stay holder cover as shown in the illustration.


20. INSTALL VISOR ASSEMBLY LH

  1. B173261
    Install the visor assembly LH with the 2 screws.


21. INSTALL VISOR BRACKET COVER (for LH Side)

  1. B139566
    Engage the 4 claws and install the visor bracket cover.


22. INSTALL VISOR ASSEMBLY RH

HINT:
Use the same procedure for the RH side and the LH side.


23. INSTALL VISOR BRACKET COVER (for RH Side)

HINT:
Use the same procedure for the RH side and the LH side.


24. INSTALL ROOF CONSOLE BOX ASSEMBLY

  1. B173251
    Connect the connector.

  1. Engage the 3 guides, 2 clips, fastener, and install the roof console box assembly.


25. INSTALL ROOF SIDE INNER GARNISH ASSEMBLY LH (w/o Power Back Door)

  1. w/ Rear No. 2 Seat:

    1. B173267
      Engage the 2 guides and 5 clips.

    2. Install the roof side inner garnish assembly LH with the bolt.

    3. B175157
      Engage the 2 guides and the 2 claws, and install the No. 2 seat outer belt guide.

  1. w/o Rear No. 2 Seat:

    1. B173268
      Engage the 2 guides and 5 clips.

    2. Install the roof side inner garnish assembly LH with the bolt.


26. INSTALL ROOF SIDE INNER GARNISH ASSEMBLY LH (w/ Power Back Door)

  1. w/ Rear No. 2 Seat:

    1. B173265
      Engage the 2 guides and 5 clips.

    2. Install the roof side inner garnish assembly LH with the bolt.

    3. B175157
      Engage the 2 guides and the 2 claws, and install the No. 2 seat outer belt guide.

  1. w/o Rear No. 2 Seat:

    1. B173266
      Engage the 2 guides and 5 clips.

    2. Install the roof side inner garnish assembly LH with the bolt.


27. INSTALL QUARTER PILLAR GARNISH LH

  1. B173264
    Engage the 2 guides and the 2 clips, and install the quarter pillar garnish LH as shown in the illustration.

  1. B175156
    Engage the 2 guides and the 2 claws, and install the No. 1 seat outer belt guide.


28. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH
  1. Engage the 4 clips and the 7 claws.

  1. Install the 2 clips.

  1. Install the deck trim side panel assembly LH with the 2 bolts.

    B173613


29. CONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY LH

  1. B170934E01
    Connect the floor anchor end of the rear No. 1 seat outer belt assembly and install the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not allow the anchor part of the rear No. 1 seat outer belt assembly to overlap the protruding part of the floor panel.


30. INSTALL FRONT DECK SIDE TRIM COVER LH

  1. B175145
    Engage the 4 claws and install the 2 front deck side trim covers LH.


31. INSTALL NO. 2 DECK SIDE TRIM HOOK

  1. B173612
    Install the No. 2 deck side trim hook with the screw.


32. INSTALL ROPE HOOK ASSEMBLY (for LH Side)

  1. B173599
    for Front Side:

    1. Install the rope hook assembly with the bolt.

      Torque:
      6.5 N*m{ 66 kgf*cm , 58 in.*lbf }

    2. Engage the 2 claws.

  1. B173601
    for Rear Side:

    1. Install the rope hook assembly with the bolt.

      Torque:
      6.5 N*m{ 66 kgf*cm , 58 in.*lbf }

    2. Engage the 2 claws.


33. INSTALL REAR DECK TRIM COVER (w/o Remote Folding Function)

  1. B173602
    Engage the 10 claws and install the rear deck trim cover.


34. INSTALL RECLINING REMOTE CONTROL LEVER BEZEL LH (w/ Remote Folding Function)

  1. B173603
    Engage the 5 claws and install the reclining remote control bezel LH.


35. INSTALL REAR POWER OUTLET SOCKET COVER

  1. E151328
    Engage the 2 claws and install the rear power outlet socket cover.


36. INSTALL REAR POWER POINT SOCKET ASSEMBLY

  1. E151490
    Engage the claw and install the rear power point socket assembly.

  1. Connect the connector.


37. INSTALL REAR COMBINATION LIGHT SERVICE COVER LH

  1. B175146
    Engage the 2 guides and 6 claws, and install the rear combination light service cover LH.


38. INSTALL SIDE TRIM COVER LH

  1. B173597
    Engage the 10 claws and install the side trim cover LH.


39. INSTALL DECK SIDE TRIM LH

  1. B173624
    Engage the 3 guides and 4 claws as shown in the illustration.

  1. B173596
    Install the deck side trim LH with the bolt.


40. INSTALL DECK SIDE TRIM COVER NO.2

  1. B175144
    Engage the 2 claws and install the deck side trim cover LH.


41. INSTALL ROOF SIDE INNER GARNISH ASSEMBLY RH (w/o Rear No. 2 Seat)

HINT:
Use the same procedure for the RH side and the LH side.


42. INSTALL ROOF SIDE INNER GARNISH ASSEMBLY RH (w/ Rear No. 2 Seat)

HINT:
Use the same procedure for the RH side and the LH side.


43. INSTALL QUARTER PILLAR GARNISH RH

HINT:
Use the same procedure for the RH side and the LH side.


44. INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH
  1. Engage the 4 clips and the 7 claws.

  1. Install the 2 clips.

  1. Install the deck trim side panel assembly RH with the 3 bolts.

    B173622


45. CONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY RH

HINT:
Use the same procedure for the RH side and the LH side.


46. INSTALL FRONT DECK SIDE TRIM COVER RH

HINT:
Use the same procedure for the RH side and the LH side.


47. INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK

HINT:
Use the same procedure for the No. 1 luggage compartment trim hook and the No. 2 deck side trim hook.


48. INSTALL ROPE HOOK ASSEMBLY (for RH Side)

HINT:
Use the same procedure for the RH side and the LH side.


49. INSTALL REAR COMBINATION LIGHT SERVICE COVER RH

  1. B173619
    Engage the 2 guides and 6 claws, and install the rear combination light service cover RH.


50. INSTALL REAR ROOM TEMPERATURE SENSOR (w/ Rear Automatic Air Conditioning System)
  1. Connect the connector.

  1. E150364
    Engage the 4 claws and install the rear room temperature sensor.


51. INSTALL SIDE TRIM COVER RH (w/o Rear Automatic Air Conditioning System)

  1. B173610
    Engage the 4 claws, and install the side trim cover RH.


52. INSTALL DECK SIDE TRIM RH

HINT:
Use the same procedure for the RH side and the LH side.


53. INSTALL DECK SIDE TRIM COVER NO.1

HINT:
Use the same procedure for the RH side and the LH side.


54. INSTALL REAR SEAT SIDE GARNISH CAP (w/o Rear Air Conditioning System)

  1. B173615
    Engage the guide and the 8 claws, and install the rear seat side garnish cap.


55. INSTALL REAR SEAT SIDE GARNISH CAP (w/ Rear Air Conditioning System)

  1. B173617
    Engage the guide and the 6 claws.

  1. Install the rear seat side garnish cap with the screw.


56. INSTALL REAR FLOOR FINISH PLATE

  1. B173609
    Engage the 4 clips and the 4 claws, and install the rear floor finish plate.


57. INSTALL REAR NO. 2 SEAT ASSEMBLY (w/ Rear No. 2 Seat)

  1. B173781
    Install the rear No. 2 seat assembly with the 4 bolts.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }


58. CONNECT REAR SEAT LAP TYPE BELT ASSEMBLY LH (w/ Rear No. 2 Seat)

  1. B170936
    Install the rear seat lap type belt assembly LH with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    After installing the belt, check that it is not twisted.


59. CONNECT REAR SEAT LAP TYPE BELT ASSEMBLY RH (w/ Rear No. 2 Seat)
  1. Install the rear seat lap type belt assembly RH with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    After installing the belt, check that it is not twisted.


60. INSTALL REAR NO. 2 SEAT INNER BELT ASSEMBLY (w/ Rear No. 2 Seat)

  1. B170935
    Install the rear No. 2 seat inner belt assembly with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not allow the anchor part of the rear No. 2 seat inner belt assembly to overlap the protruding part of the rear No. 2 seat bracket.

    HINT:
    Use the same procedure for the RH side and LH side.


61. INSTALL REAR DECK FLOOR BOX (w/o Rear No. 2 Seat)

  1. B173679
    Install the rear deck floor box with the 2 nuts.


62. INSTALL DECK FLOOR BOARD ASSEMBLY (w/o Rear No. 2 Seat)

  1. B178561
    Install the 2 nuts and the deck floor board assembly.

  1. Engage the 3 claws.


63. INSTALL REAR MAT

  1. B173249
    Install the rear mat.


64. INSTALL DECK FLOOR BOARD ASSEMBLY (w/ Rear No. 2 Seat)

  1. B178560
    Install the rear deck floor board assembly with the 4 nuts and 4 bolts.


65. INSTALL DECK SIDE TRIM BOX LH

  1. Install the deck side trim box LH as shown in the illustration.

    B178555

  1. B173243E01
    Install the 2 deck side trim clips and the clip.


66. INSTALL REAR SEAT SIDE COVER LH (w/ Rear No. 2 Seat)

  1. B173607
    Engage the 2 clips and install the rear seat side cover LH.


67. INSTALL DECK SIDE TRIM BOX RH

  1. Install the deck side trim box RH as shown in the illustration.

    B178553

  1. B173247E01
    Install the 2 deck side trim clips and the clip.


68. INSTALL JACK CARRIER ASSEMBLY (for LHD)

  1. B178549
    Engage the 3 claws, and install the jack carrier assembly.


69. INSTALL JACK CARRIER ASSEMBLY (for RHD)

  1. B179786
    Engage the 3 claws, and install the jack carrier assembly.


70. INSTALL JACK ASSEMBLY (for LHD)

  1. B173245
    Install the jack assembly.


71. INSTALL JACK ASSEMBLY (for RHD)

  1. B178566
    Install the jack assembly.


72. INSTALL JACK CARRIER CUSHION (for LHD)

  1. B178550
    Install the jack carrier cushion.


73. INSTALL JACK CARRIER CUSHION (for RHD)

  1. B178551
    Install the jack carrier cushion.


74. INSTALL JACK CARRIER SUPPORT

75. INSTALL REAR SEAT SIDE COVER RH (w/ Rear No. 2 Seat)

  1. B173608
    Engage the 2 clips and install the rear seat side cover RH.


76. INSTALL REAR NO. 1 FLOOR BOARD (w/o Rear No. 2 Seat)

  1. B175152
    Engage the 3 guides and 3 clips and install the rear No. 1 floor board.


77. INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)

78. INSTALL NO. 2 DECK BOARD SUB-ASSEMBLY

  1. B173244
    Engage the 2 guides and install the No. 2 deck board sub-assembly.


79. INSTALL NO. 3 DECK BOARD SUB-ASSEMBLY

  1. B173242
    Engage the 2 guides and install the No. 3 deck board sub-assembly.


80. INSTALL DECK BOARD ASSEMBLY

  1. B173240
    Install the deck board sub-assembly.


81. INSTALL CENTER PILLAR GARNISH LH

  1. B173229
    Engage the 2 guides and the clip.

  1. Install the center pillar garnish LH with the clip and screw.


82. CONNECT FRONT SEAT OUTER BELT ASSEMBLY LH

  1. B170910
    Install the floor end of the front seat outer belt assembly with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. Check if the ELR locks.

    NOTICE:
    The check should be performed with the outer belt assembly installed.


    1. With the belt assembly installed, check that the belt locks when it is pulled out quickly.


83. INSTALL LOWER CENTER PILLAR GARNISH LH

  1. B173231
    Engage the 2 claws and the 2 clips, and install the lower center pillar garnish LH.


84. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

  1. B173233E01
    Align the alignment mark (red) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip LH.

    NOTICE:
    After installation, check that the corners fit correctly.


85. INSTALL REAR DOOR SCUFF PLATE LH

  1. B173228
    Engage the guide, 3 clips and 5 claws, and install the rear door scuff plate LH.


86. INSTALL FRONT PILLAR GARNISH LH

  1. B173226E01
    Remove the protective cover.

  1. B173223E01
    Install a new clip <A> on the front pillar garnish LH.

  1. Engage the 3 guides and 2 clips, then install the front pillar garnish LH.


87. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

  1. B173235E01
    Align the alignment mark (blue) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip LH.

    NOTICE:
    After installation, check that the corners fit correctly.


88. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH

  1. B173227
    Engage the claw and clip, install the cowl side trim sub-assembly LH.

  1. Install the clip.


89. INSTALL FRONT DOOR SCUFF PLATE LH

  1. B173224
    Engage the guide and the 8 claws, and install the front door scuff plate LH.


90. INSTALL CENTER PILLAR GARNISH RH

HINT:
Use the same procedure for the RH side and the LH side.


91. CONNECT FRONT SEAT OUTER BELT ASSEMBLY RH

HINT:
Use the same procedure for the RH side and the LH side.


92. INSTALL LOWER CENTER PILLAR GARNISH RH

HINT:
Use the same procedure for the RH side and the LH side.


93. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH

  1. B173237E01
    Align the alignment mark (green) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip RH.

    NOTICE:
    After installation, check that the corners fit correctly.


94. INSTALL REAR DOOR SCUFF PLATE RH

HINT:
Use the same procedure for the RH side and the LH side.


95. INSTALL FRONT PILLAR GARNISH RH

  1. B173685E01
    Remove the protective cover.

  1. B173683E01
    Install a new clip <A> on the front pillar garnish RH.

  1. Engage the 3 guides and 2 clips, then install the front pillar garnish RH.


96. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

  1. B173239E01
    Align the alignment mark (pink) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip RH.

    NOTICE:
    After installation, check that the corners fit correctly.


97. INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:
Use the same procedure for the RH side and the LH side.


98. INSTALL FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedure for the RH side and the LH side.


99. INSTALL REAR NO. 1 SEAT ASSEMBLY LH

  1. B173778
    Temporarily install the 2 bolts on the front side of the seat.

  1. B173780
    Temporarily install the 3 bolts on the rear side of the seat.

  1. Install the rear No. 1 seat assembly with the 5 bolts.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }


100. CONNECT REAR NO. 1 SEAT LOCK CABLE ASSEMBLY LH (w/ Remote Folding Function)

  1. Remove the rear seat reclining control cable from the carpet hole.

    B180395E01

  1. Connect the rear seat reclining control cable as shown in the illustration.

  1. Connect the rear No. 1 seat lock cable assembly as shown in the illustration.

    B173771E01

  1. B174591
    Engage the 2 claws and connect the rear No. 1 seat lock cable assembly as shown in the illustration.

  1. Return the seatback to the upright position.

  1. Pull up the adjuster's lock piece to lock it as shown in the illustration.

    B180389E01

    NOTICE:
    When pressing the lock piece, make sure the adjuster's spring is not compress.


101. INSPECT REAR SEAT SLIDE ADJUSTER LOCK (for LH Side)
  1. Check that the left and right adjusters lock simultaneously when sliding the seat.

  1. If the left and right adjusters do not lock simultaneously, adjust by loosening the bolts securing the seat.


102. INSTALL REAR SEAT LEG SIDE COVER LH

  1. B173779
    Engage the clip.

  1. Engage the 3 claws and install the rear seat leg side cover.


103. INSTALL REAR INNER TRACK BRACKET COVER LH

  1. B173777
    Engage the 4 claws and install the rear inner track bracket cover.


104. INSTALL REAR OUTER TRACK BRACKET COVER LH

  1. B173776
    Engage the 4 claws and install the rear outer track bracket cover.


105. INSTALL REAR SEAT TRACK BRACKET COVER LH

  1. B173775
    Engage the 8 claws and install the 2 rear seat track bracket covers.


106. INSTALL REAR SEAT HEADREST ASSEMBLY (for LH Side)

107. INSTALL REAR CENTER SEAT ASSEMBLY

108. INSTALL REAR NO. 1 SEAT ASSEMBLY RH

  1. B173764
    Temporarily install the 2 bolts on the front side of the seat.

  1. B173774
    Temporarily Install the 3 bolts on the rear side of the seat.

  1. Install the rear No. 1 seat assembly with the 5 bolts.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }


109. CONNECT REAR NO. 1 SEAT LOCK CABLE ASSEMBLY RH (w/ Remote Folding Function)

HINT:
Use the same procedure for the RH side and the LH side.


110. INSPECT REAR SEAT SLIDE ADJUSTER LOCK (for RH Side)
  1. Check that the left and right adjusters lock simultaneously when sliding the seat.

  1. If the left and right adjusters do not lock simultaneously, adjust by loosening the bolts securing the seat.


111. INSTALL REAR SEAT LEG SIDE COVER RH

  1. B173765
    Engage the clip.

  1. Engage the 3 claws and install the rear seat leg side cover.


112. INSTALL REAR INNER TRACK BRACKET COVER RH

  1. B173761
    Engage the 4 claws and install the rear inner track bracket cover.


113. INSTALL REAR OUTER TRACK BRACKET COVER RH

  1. B173763
    Engage the 4 claws and install the rear outer track bracket cover.


114. INSTALL REAR SEAT TRACK BRACKET COVER RH

  1. B173760
    Engage the 8 claws and install the 2 seat track bracket covers.


115. INSTALL REAR SEAT HEADREST ASSEMBLY (for RH Side)

116. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


117. RESET SLIDING ROOF DRIVE GEAR ASSEMBLY
(Click here)

118. INSPECT SLIDING ROOF SYSTEM
  1. Turn the ignition switch on (IG).

  1. When the roof glass is fully closed, press the OPEN switch for 0.3 seconds or more. Check that the roof glass automatically slides until it is fully opened.

  1. When the roof glass is fully open, press the CLOSE switch for 0.3 seconds or more. Check that the roof glass automatically slides until it is fully closed.

  1. When the roof glass is fully closed, press the UP switch for 0.3 seconds or more. Check that the roof glass automatically tilts until it is fully tilted upward.

  1. When the roof glass is fully tilted upward, press the DOWN switch for 0.3 seconds or more. Check that the roof glass automatically tilts until it is fully tilted downward.

  1. When the auto operation is operating, check that pressing any personal light switch stops the roof glass operation.

    HINT:
    When pressing the switch for 0.3 seconds or less, the roof glass moves but auto operation does not operate.


119. INSPECT SRS WARNING LIGHT
(Click here)
← INSTALLATION (May 2007 – Jul 2008)INSTALLATION (from Jul 2010) →