REMOVAL
Removal / installation · Vehicles built from Jul 2010
Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010
| 1.
REMOVE REAR DOOR SCUFF PLATE LH
|
 |
- Disengage the 5 claws, 3 clips and guide, and remove the rear door scuff plate LH.
| 2.
REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH
|
 |
- Remove the rear door opening trim weatherstrip LH.
| 3.
REMOVE REAR DOOR SCUFF PLATE RH
|
 |
- HINT:
- Use the same procedure for the RH side and the LH side.
| 4.
REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH
|
 |
- HINT:
- Use the same procedure for the RH side and the LH side.
| 5.
REMOVE DECK BOARD ASSEMBLY
|
 |
- Remove the deck board assembly.
| 6.
REMOVE NO. 3 DECK BOARD SUB-ASSEMBLY
|
 |
- Disengage the 2 guides and remove the No. 3 deck board sub-assembly.
| 7.
REMOVE NO. 2 DECK BOARD SUB-ASSEMBLY
|
 |
- Disengage the 2 guides and remove the No. 2 deck board sub-assembly.
| 8.
REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)
|
 |
Remove the tonneau cover assembly.
| 9.
REMOVE REAR NO. 1 FLOOR BOARD (w/o Rear No. 2 Seat)
|
 |
- Disengage the 3 clips and 3 guides, and remove the rear No. 1 floor board.
| 10.
REMOVE REAR SEAT SIDE COVER LH (w/ Rear No. 2 Seat)
|
 |
- Disengage the 2 clips and remove the rear seat side cover LH.
| 11.
REMOVE DECK SIDE TRIM BOX LH
|
 |
- Remove the 2 deck side trim clips and clip.
Remove the deck side trim box LH as shown in the illustration.


| 12.
REMOVE REAR SEAT SIDE COVER RH (w/ Rear No. 2 Seat)
|
 |
- Disengage the 2 clips and remove the rear seat side cover RH.
| 13.
REMOVE JACK CARRIER SUPPORT |
|
| 14.
REMOVE JACK CARRIER CUSHION (for LHD)
|
 |
- Remove the jack carrier cushion.
| 15.
REMOVE JACK CARRIER CUSHION (for RHD)
|
 |
- Remove the jack carrier cushion.
| 16.
REMOVE JACK ASSEMBLY (for LHD)
|
 |
- Remove the jack assembly.
| 17.
REMOVE JACK ASSEMBLY (for RHD)
|
 |
- Remove the jack assembly.
| 18.
REMOVE JACK CARRIER ASSEMBLY (for LHD)
|
 |
- Using a screwdriver, disengage the 3 claws and remove the jack carrier assembly.
| 19.
REMOVE JACK CARRIER ASSEMBLY (for RHD)
|
 |
- Using a screwdriver, disengage the 3 claws and remove the jack carrier assembly.
| 20.
REMOVE DECK SIDE TRIM BOX RH
|
 |
- Remove the 2 deck side trim clips and clip.
Remove the deck side trim box RH as shown in the illustration.


| 21.
REMOVE DECK FLOOR BOARD ASSEMBLY (w/o Rear No. 2 Seat)
|
 |
- Remove the 4 bolts and 4 nuts.
Remove the deck floor board assembly.
| 22.
REMOVE REAR MAT
|
 |
- Remove the rear mat.
| 23.
REMOVE DECK FLOOR BOARD ASSEMBLY (w/ Rear No. 2 Seat)
|
 |
- Disengage the 3 claws.
Remove the 2 nuts and deck floor board assembly.
| 24.
REMOVE REAR DECK FLOOR BOX (w/o Rear No. 2 Seat)
|
 |
- Remove the 2 nuts and the deck floor box.
| 25.
REMOVE REAR NO. 2 SEAT INNER BELT ASSEMBLY (w/ Rear No. 2 Seat)
|
 |
- Remove the bolt and rear No. 2 seat inner belt assembly.
- HINT:
- Use the same procedure for the RH side and LH side.
| 26.
DISCONNECT REAR NO. 2 SEAT OUTER BELT ASSEMBLY LH (w/ Rear No. 2 Seat)
|
 |
- Remove the bolt and disconnect the rear No. 2 seat outer belt assembly LH.
| 27.
DISCONNECT REAR NO. 2 SEAT OUTER BELT ASSEMBLY RH (w/ Rear No. 2 Seat)
|
 |
- HINT:
- Use the same procedure as for the LH side.
| 28.
REMOVE REAR NO. 2 SEAT ASSEMBLY (w/ Rear No. 2 Seat)
|
 |
Remove the bolt on the front of the seat.


Remove the 6 bolts on the rear of the seat and the rear No. 2 seat assembly.


| 29.
REMOVE REAR FLOOR FINISH PLATE
|
 |
- Disengage the 4 clips and 4 claws, and remove the rear floor finish plate.
| 30.
REMOVE DECK SIDE TRIM COVER NO.2
|
 |
- Using a screwdriver, disengage the 2 claws and remove the deck side trim cover LH.
- HINT:
- Tape the screwdriver tip before use.
| 31.
REMOVE DECK SIDE TRIM LH
|
 |
- Remove the bolt.
- Disengage the 4 claws and 3 guides, and remove the deck side trim LH as shown in the illustration.
| 32.
REMOVE SIDE TRIM COVER LH
|
 |
- Disengage the 10 claws and remove the side trim cover LH.
| 33.
REMOVE REAR COMBINATION LIGHT SERVICE COVER LH
|
 |
- Using a screwdriver, disengage the 6 claws and 2 guides, and remove the rear combination light service cover LH.
- HINT:
- Tape the screwdriver tip before use.
| 34.
REMOVE REAR POWER POINT SOCKET ASSEMBLY
|
 |
Disconnect the connector.
- Disengage the claw and remove the rear power point socket assembly.
| 35.
REMOVE REAR POWER OUTLET SOCKET COVER
|
 |
- Disengage the 2 claws and remove the rear power outlet socket cover.
| 36.
REMOVE REAR DECK TRIM COVER (w/o Remote Folding Function)
|
 |
- Disengage the 10 claws and remove the rear deck trim cover.
| 37.
REMOVE RECLINING REMOTE CONTROL BEZEL LH (w/ Remote Folding Function)
|
 |
- Disengage the 5 claws and remove the reclining remote control lever bezel LH.
| 38.
REMOVE ROPE HOOK ASSEMBLY (for LH Side)
|
 |
- for Front Side:
Using a screwdriver, disengage the 2 claws.
- HINT:
- Tape the screwdriver tip before use.
Remove the bolt and rope hook assembly.
- for Rear Side:
Using a screwdriver, disengage the 2 claws.
- HINT:
- Tape the screwdriver tip before use.
Remove the bolt and rope hook assembly.
| 39.
REMOVE NO. 2 DECK SIDE TRIM HOOK
|
 |
- Remove the screw and No. 2 deck side trim hook.
| 40.
REMOVE FRONT DECK SIDE TRIM COVER LH
|
 |
- Using a screwdriver, disengage the 4 claws and remove the 2 front deck side trim covers LH.
- HINT:
- Tape the screwdriver tip before use.
| 41.
DISCONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY LH
|
 |
- Remove the bolt and disconnect the floor end of the rear No. 1 seat outer belt assembly.
| 42.
REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH
|
 |
Remove the 2 bolts.
Remove the 2 clips.
Disengage the 7 claws and 4 clips, and remove the deck trim side panel assembly LH.


| 43.
REMOVE ROOF SIDE INNER GARNISH ASSEMBLY LH (w/o Power Back Door)
|
 |
w/o Rear No. 2 Seat:
- Remove the bolt.
Disengage the 5 clips and 2 guides, and remove the roof side inner garnish assembly LH.
w/ Rear No. 2 Seat:
- Disengage the 2 claws and 2 guides, and remove the rear No. 2 seat outer belt guide.
- Remove the bolt.
Disengage the 5 clips and 2 guides, and remove the roof side inner garnish assembly LH.
| 44.
REMOVE ROOF SIDE INNER GARNISH ASSEMBLY LH (w/ Power Back Door)
|
 |
w/o Rear No. 2 Seat:
- Remove the bolt.
Disengage the 5 clips and 2 guides, and remove the roof side inner garnish assembly LH.
w/ Rear No. 2 Seat:
- Disengage the 2 claws and 2 guides, and remove the rear No. 2 seat outer belt guide.
- Remove the bolt.
Disengage the 5 clips and 2 guides, and remove the roof side inner garnish assembly LH.
| 45.
REMOVE REAR SEAT SIDE GARNISH CAP (w/o Rear Air Conditioning System)
|
 |
- Disengage the 8 claws and guide, and remove the rear seat side garnish cap.
| 46.
REMOVE REAR SEAT SIDE GARNISH CAP (w/ Rear Air Conditioning System)
|
 |
- Remove the screw.
Disengage the 6 claws and the guide, and remove the rear seat side garnish cap.
| 47.
REMOVE DECK SIDE TRIM COVER NO.1
|
 |
- HINT:
- Use the same procedure for the RH side and the LH side.
| 48.
REMOVE DECK SIDE TRIM RH
|
 |
- HINT:
- Use the same procedure for the RH side and the LH side.
| 49.
REMOVE SIDE TRIM COVER RH (w/o Rear Automatic Air Conditioning System)
|
 |
- Disengage the 4 claws and remove the side trim cover RH.
| 50.
REMOVE REAR ROOM TEMPERATURE SENSOR (w/ Rear Automatic Air Conditioning System)
|
 |
- Disengage the 4 claws and remove the rear room temperature sensor.
Disconnect the connector.
| 51.
REMOVE REAR COMBINATION LIGHT SERVICE COVER RH
|
 |
- Using a screwdriver, disengage the 6 claws and 2 guides, and remove the rear combination light service cover RH.
- HINT:
- Tape the screwdriver tip before use.
| 52.
REMOVE ROPE HOOK ASSEMBLY (for RH Side)
|
 |
- HINT:
- Use the same procedure for the RH side and the LH side.
| 53.
REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK
|
 |
- HINT:
- Use the same procedure for the No. 1 luggage compartment trim hook and the No. 2 deck side trim hook.
| 54.
REMOVE FRONT DECK SIDE TRIM COVER RH
|
 |
- HINT:
- Use the same procedure for the RH side and the LH side.
| 55.
DISCONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY RH
|
 |
- HINT:
- Use the same procedure for the RH side and the LH side.
| 56.
REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH
|
 |
Remove the 3 bolts.
Remove the 2 clips.
Disengage the 7 claws and 4 clips, and remove the deck trim side panel assembly RH.


| 57.
REMOVE ROOF SIDE INNER GARNISH ASSEMBLY RH (w/o Rear No. 2 Seat)
|
 |
- HINT:
- Use the same procedure for the RH side and the LH side.
| 58.
REMOVE ROOF SIDE INNER GARNISH ASSEMBLY RH (w/ Rear No. 2 Seat)
|
 |
- HINT:
- Use the same procedure for the RH side and the LH side.
| 59.
REMOVE REAR QUARTER PANEL MUDGUARD LH
|
 |
- Remove the 2 screws (A).
Using a 4 mm hexagon wrench, remove the 3 screws (B).
| 60.
REMOVE REAR QUARTER PANEL MUDGUARD RH
|
 |
- HINT:
- Use the same procedure for the RH side and LH side.
| 61.
REMOVE REAR BUMPER ASSEMBLY
|
 |
- Put protective tape around the rear bumper assembly.
Text in Illustration
*1
|
Protective Tape
|
- Remove the 2 screws.
- HINT:
- Use the same procedure for the RH side and LH side.
- Remove the 5 clips, 2 screws and 2 bolts.
- Disengage the 7 claws and disconnect the rear bumper assembly.
- HINT:
- Use the same procedure for the RH side and LH side.
w/ Rear Fog Light:
Disconnect the rear fog light connector, and remove the rear bumper assembly.
| 62.
REMOVE REAR COMBINATION LIGHT ASSEMBLY |
 |
- Disconnect the connectors.
Remove the 2 nuts.
- Remove the screw.
Disengage the 2 pins and guide, and remove the rear combination light assembly.
Text in Illustration
*1
|
Pin
|
*2
|
Guide
|