2007-2013 Highlander Kluger · Service Manual BODY ELECTRICAL

INSTALLATION

Removal / installation · Vehicles built May 2007 – Jul 2008

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010


1. INSTALL SPIRAL CABLE

  1. C147575E02
    Engage the 6 claws and 2 pins, and install the spiral cable to the steering angle sensor.


2. INSTALL SPIRAL CABLE WITH STEERING ANGLE SENSOR
  1. Check that the front wheels are facing straight ahead.

  1. Set the turn signal switch to the neutral position.

    NOTICE:
    If it is not in the neutral position, the turn signal switch pin may be snapped.

  1. C165095
    Install the spiral cable with steering angle sensor with the 3 claws.

    NOTICE:
    When replacing the spiral cable with a new one, remove the lock pin before installing the steering wheel assembly.

  1. Connect the connectors to the spiral cable with steering angle sensor.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.


3. INSTALL STEERING COLUMN COVER

  1. C165716
    Engage the claw to install the upper steering column cover.

  1. C166128
    Engage the 2 claws to install the lower steering column cover.

  1. C165715
    Install the 2 screws.

    Torque:
    2.0 N*m{ 20 kgf*cm , 18 in.*lbf }


4. INSTALL HORN BUTTON WIRE SUB-ASSEMBLY (w/o Steering Pad Switch)
  1. Connect the connector and install the horn button wire sub-assembly.


5. ADJUST SPIRAL CABLE
  1. Check that the ignition switch is off.

  1. Check that the battery negative (-) cable is disconnected.

    CAUTION:
    Wait for at least 90 seconds after disconnecting the cable to prevent airbag deployment.

  1. C165096
    Rotate the spiral cable counterclockwise slowly by hand until it stops.

    NOTICE:
    Do not turn the spiral cable using the airbag wire harness.

  1. C165097E01
    Rotate the spiral cable clockwise approximately 2.5 turns to align the marks.

    NOTICE:
    Do not turn the spiral cable using the airbag wire harness.

    HINT:
    The spiral cable will rotate approximately 2.5 turns to both the left and right from the center.


6. INSTALL STEERING WHEEL ASSEMBLY

  1. C165708E01
    Align the matchmarks on the steering wheel assembly and steering main shaft.

  1. Install the steering wheel assembly set nut.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }

  1. Connect the connectors to the spiral cable sub-assembly.


7. INSTALL STEERING PAD
  1. Check that the ignition switch is off.

  1. Check that the battery negative (-) terminal is disconnected.

    CAUTION:
    Wait for at least 90 seconds after disconnecting the cable to prevent airbag deployment.

  1. C165092
    Support the steering pad with one hand as shown in the illustration.

  1. C165093
    Connect the 2 airbag connectors to the steering pad.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.

  1. Connect the horn connector to the steering pad.

  1. Confirm that the circumference groove of the "TORX" screw fits in the screw case, and place the steering pad onto the steering wheel assembly.

  1. C166982E01
    Using a "TORX" socket wrench (T30), tighten the 2 "TORX" screws.

    Torque:
    8.8 N*m{ 90 kgf*cm , 78 in.*lbf }


8. INSTALL LOWER NO. 3 STEERING WHEEL COVER

  1. C165090
    Install the lower No. 3 steering wheel cover with the claw.


9. INSTALL LOWER NO. 2 STEERING WHEEL COVER

  1. C165091
    Install the lower No. 2 steering wheel cover with the claw.


10. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


11. INSPECT STEERING PAD

  1. C166979
    With the steering pad installed on the vehicle, perform a visual check. If there are any defects as mentioned below, replace the steering pad with a new one:
    1. Cuts, minute cracks or marked discoloration on the steering pad top surface or grooves.

  1. Make sure that the horn sounds.

    HINT:
    If the horn does not sound, inspect the horn system (Click here).


12. INSPECT STEERING WHEEL CENTER POINT

13. INSPECT SRS WARNING LIGHT
  1. Inspect the SRS warning light (Click here).

← INSPECTION (from May 2007)INSTALLATION (Aug 2008 – Jun 2010) →