2007-2013 Highlander Kluger · Service Manual BODY

REASSEMBLY

Removal / installation · Vehicles built from May 2007


1. INSTALL REAR SEAT CUSHION SPRING ASSEMBLY

  1. B206113
    Using a T45 "TORX" socket wrench, install the rear seat cushion spring assembly with the 4 bolts and 2 bushes.

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }


2. INSTALL REAR SEAT HOOK

  1. B196403
    Engage the claw to install the rear seat hook.


3. INSTALL NO. 2 REAR SEAT RECLINING CONTROL CABLE

  1. B206112
    Engage the claw.

  1. Engage the rear seat hook.

  1. Engage the 4 cable clamps to install the No. 2 rear seat reclining control cable.


4. INSTALL NO. 1 REAR SEAT RECLINING CONTROL CABLE (w/ Remote Folding Function)

  1. B206111
    Install the clamp.

  1. Engage the 2 clamps.

  1. Engage the 6 cable clamps to install the No. 1 rear seat reclining control cable.


5. INSTALL NO. 2 REAR SEAT COVER

  1. B206110
    Install the No. 2 rear seat cover.


6. INSTALL REAR SEAT CUSHION SIDE COVER

  1. B173829
    Engage the claw.

  1. Install the rear seat cushion side cover with the 2 screws.


7. INSTALL REAR NO. 2 SEATBACK COVER

  1. B173828
    Engage the claw.

  1. Install the rear No. 2 seatback cover with the 2 screws.


8. INSTALL REAR NO. 1 SEAT SHOULDER BELT COVER

  1. B196398
    Engage the guide.

  1. Engage the claw to install the rear No. 1 seat shoulder belt cover.


9. INSTALL REAR CENTER SEAT OUTER BELT ASSEMBLY

  1. B170904
    Install the rear center seat outer belt assembly with the bolt and nut.

    Torque:
    Bolt:
    7.5 N*m{ 77 kgf*cm , 66 in.*lbf }
    Nut:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }


10. INSTALL BELT SUPPORT PLATE

  1. B170939
    Engage the 3 claws to install the belt support plate.


11. INSTALL SEPARATE TYPE REAR NO. 1 SEATBACK COVER

  1. B173827E01
    Using hog ring pliers, install the separate type rear No. 1 seatback cover with 10 new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, take care to minimize wrinkles as much as possible.


12. INSTALL REAR NO. 1 SEATBACK COVER WITH PAD

  1. B173823
    Engage the hooks to install the rear No. 1 seatback cover with pad.


13. INSTALL REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY RH

  1. B196397
    Engage the 2 claws to install the rear No. 1 seat headrest support assembly RH.


14. INSTALL REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY LH

  1. B196396
    Engage the 2 claws to install the rear No. 1 seat headrest support assembly LH.


15. INSTALL REAR SEATBACK BOARD CARPET ASSEMBLY

  1. B206116
    Engage 2 guides.

  1. Engage the 2 clips.

  1. Engage the 19 claws to install the rear seatback board carpet assembly as shown in the illustration.


16. INSTALL REAR SEATBACK LOCK ASSEMBLY

  1. B206108
    Install the rear seatback lock assembly with the 2 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }


17. INSTALL REAR SEATBACK LOWER LOCK BEZEL

  1. B196393
    Install the rear seatback lower lock bezel with the 2 screws.

  1. B196392
    Engage the snap to install the rear seat track handle as shown in the illustration.

  1. B196390
    Engage the 4 claws.

  1. Install the rear center seat outer belt cover with the screw.


18. CONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY

  1. B170903
    Connect the rear center seat outer belt with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }


19. INSTALL REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY

  1. Connect the rear seat lock control cable as shown in the illustration.

    B173809

  1. B206107
    Engage the guide.

  1. Install the rear seat lock control lever sub-assembly with the 2 screws.


20. INSTALL REAR SEAT LOCK STRIKER COVER

  1. B206117
    Engage the guide.

  1. Engage the claw to install the rear seat lock striker cover.


21. INSTALL REAR SEATBACK COVER

  1. B173805
    Engage the 4 claws to install the rear seatback cover.


22. INSTALL TONNEAU COVER HOOK HOLDER

  1. B196386
    Install the 2 tonneau cover hook holders with the 2 screws.


23. INSTALL REAR SEAT ARMREST ASSEMBLY

  1. B173802
    Install the rear seat armrest assembly with the bolt.

    Torque:
    33 N*m{ 337 kgf*cm , 24 ft.*lbf }


24. INSTALL NO. 1 SEAT ARMREST CAP

  1. B173801
    Engage the 2 claws to install the No. 1 seat armrest cap.


25. INSTALL REAR NO. 1 SEAT INNER BELT ASSEMBLY

  1. B170974
    Install the rear No. 1 seat inner belt assembly with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }


26. INSTALL REAR SEAT RECLINING INNER COVER

  1. B206105
    Engage the guide.

  1. Install the rear seat reclining inner cover with the screw.


27. INSTALL SEAT TRACK UPPER RAIL COVER

  1. B206104
    Engage the claw.

  1. Install the seat track upper rail cover with the screw.


28. INSTALL RECLINING ADJUSTER INSIDE COVER LH

  1. B206150
    Engage the guide to install the reclining adjuster inside cover LH.


29. INSTALL REAR SEAT NO. 1 RECLINING COVER

  1. B206149
    Engage the 2 guides.

  1. Engage the claw.

  1. Install the rear seat No. 1 reclining cover with the screw.


30. INSTALL NO. 1 REAR SEAT COVER (for Rear Side)

  1. B196382
    Engage the 2 hooks to install the No. 1 rear seat cover.


31. INSTALL NO. 1 REAR SEAT COVER (for RH Side)

  1. B206103
    Engage the 2 hooks to install the No. 1 rear seat cover.


32. INSTALL NO. 1 REAR SEAT COVER (for LH Side)

  1. B206102
    Engage the 4 hooks to install the No. 1 rear seat cover.


33. INSTALL SEPARATE TYPE REAR NO. 1 SEAT CUSHION COVER

  1. B173799E01
    Using hog ring pliers, install the separate type rear No. 1 seat cushion cover with 11 new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, take care to minimize wrinkles as much as possible.


34. INSTALL REAR NO. 1 SEAT CUSHION COVER WITH PAD

  1. B173833E01
    Using hog ring pliers, install 3 new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, take care to minimize wrinkles as much as possible.

  1. B206101
    Engage the 12 hooks.

  1. B196379
    Engage the 3 buttons.

  1. B173832E01
    Using hog ring pliers, install 2 new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, take care to minimize wrinkles as much as possible.

  1. Install the 2 hooks.

  1. B180396
    Engage the 2 hooks to install the rear No. 1 seat cushion cover with pad.


35. INSTALL REAR SEAT FRONT CUSHION MOULDING

  1. B196378
    Install the rear seat front cushion moulding with the screw.


36. INSTALL REAR SEAT LOCK ASSEMBLY

  1. B196377
    Install the rear seat lock assembly with the 2 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }


37. INSTALL NO. 2 REAR SEAT BEZEL COVER

  1. B173793
    Temporarily install the No. 2 rear seat bezel cover as shown in the illustration.

  1. Engage the 2 guides.

  1. Install the rear seat bezel cover with the screw.


38. INSTALL REAR SEAT CUSHION UNDER COVER

  1. B173791
    Engage the guide.

  1. Engage the claw to install the rear seat cushion under cover.


39. INSTALL REAR SEAT 3 POINT TYPE COVER ASSEMBLY

  1. B196376
    Engage the 2 claws to install the rear seat 3 point type cover assembly.


40. INSTALL REAR SIDE SEAT BAND SUB-ASSEMBLY

  1. B196374
    Install the rear side seat band sub-assembly.


41. INSTALL NO. 2 SEAT LEG COVER

  1. B196373
    Install the No. 2 seat leg cover with the 5 screws.


42. INSTALL REAR SEAT NO. 2 LEG SIDE COVER

  1. B206100
    Engage the 2 claws to install the rear seat No. 2 leg side cover.


43. INSTALL CENTER PROTECTOR COVER

  1. B196370
    Temporarily install the center protector cover.

  1. install the rear side seat band sub-assembly with the screw.

  1. B196369
    Engage the claw and guide.

  1. Install the center protector cover with the screw.


44. INSTALL SEAT ADJUSTER COVER CAP

  1. B196368
    Engage the 2 claws to install the seat adjuster cover cap.


45. INSTALL SEAT ADJUSTER COVER CAP

  1. B196372
    Engage the 2 claws to install the seat adjuster cover cap.


46. INSTALL REAR SEAT CUSHION MOULDING RH

  1. B173788
    Engage the 6 claws.

  1. Install the rear seat cushion moulding RH with the screw.


47. INSTALL SEAT ADJUSTER COVER CAP

  1. B173787
    Engage the 2 claws to install the seat adjuster cover cap.


48. INSTALL REAR SEAT CUSHION MOULDING LH

  1. B196365
    Engage the guide.

  1. Engage the 5 claws.

  1. Install the rear seat cushion moulding LH with the screw.


49. INSTALL NO. 1 RECLINING ADJUSTER RELEASE HANDLE

  1. B196364
    Install the No. 1 reclining adjuster release handle with the 3 screws.


50. INSTALL REAR SEAT RECLINING UPPER COVER

  1. B173784
    Engage the 3 claws to install the rear seat reclining upper cover.

← DISASSEMBLY (from May 2007)INSTALLATION (from May 2007) →