2007-2013 Highlander Kluger · Service Manual BODY

REMOVAL

Removal / installation · Vehicles built from Jul 2010

Versions by build date: May 2007 – Jun 2010 from Jul 2010


1. PRECAUTION

NOTICE:
  1. Be sure to use the centering jig when removing and installing the rear wiper motor assembly (for Glass Hatch Type). Failure to do so will result in a change of the location of the axis of the rear wiper motor assembly (for Glass Hatch Type), causing the wiping angle to change.
  2. After installing the rear wiper motor assembly (for Glass Hatch Type), do not open the glass hatch before installing the rear wiper link pivot.
  3. If the rear wiper motor assembly is removed without using the centering jig, the rear wiper motor assembly must be replaced with a new one.


2. REMOVE BACK WINDOW UPPER TRIM PANEL ASSEMBLY

  1. B173198
    Disengage the 4 clips and 4 claws, and remove the back window upper trim panel assembly.


3. REMOVE BACK DOOR TRIM COVER LH (w/o Power Back Door)

  1. B173199
    Disengage the 2 clips and 2 claws, and remove the back door trim cover LH.


4. REMOVE BACK DOOR SERVICE HOLE COVER LH (w/ Power Back Door)

  1. B173200
    Disengage the 6 claws, and remove the back door service hole cover LH.


5. DISCONNECT POWER BACK DOOR ROD (w/ Power Back Door)

  1. B173201
    Disconnect the power back door rod and remove the back door stay plate.


6. REMOVE BACK DOOR TRIM COVER LH (w/ Power Back Door)

  1. B173202
    Disengage the 2 clips and 2 claws, and remove the back door trim cover LH.


7. REMOVE BACK DOOR TRIM COVER RH

  1. B174214
    Disengage the 2 clips and 2 claws, and remove the back door trim cover RH.


8. REMOVE BACK DOOR LOCK COVER (for Glass Hatch Type)

  1. B173203
    Disengage the 2 claws and 4 guides, and remove the back door lock cover.


9. REMOVE ASSIST STRAP HOLE COVER

  1. B177265
    Disengage the 2 claws and 2 guides, and remove the assist strap hole cover.


10. REMOVE ASSIST STRAP ASSEMBLY

  1. B177264
    Remove the bolt and assist strap assembly.


11. REMOVE BACK DOOR TRIM PANEL ASSEMBLY

  1. B174211
    Disengage the 16 clips and remove the back door trim panel assembly.


12. REMOVE REAR WIPER SHAFT COVER

  1. E151098
    Disengage the 3 clips and remove the rear wiper shaft cover.


13. REMOVE REAR WIPER ARM HEAD CAP

  1. E150155
    Remove the rear wiper arm head cap.


14. REMOVE REAR WIPER ARM AND BLADE ASSEMBLY

  1. E150156
    Remove the nut and the rear wiper arm and blade assembly.


15. REMOVE REAR WIPER LINK CAP

  1. E150157
    Remove the rear wiper link cap.


16. REMOVE REAR WIPER LINK PIVOT

  1. E150158
    Remove the nut and the rear wiper link pivot.


17. REMOVE REAR WIPER MOTOR ASSEMBLY

  1. When reinstalling the rear wiper motor assembly:

    1. Open the glass hatch.

    2. E154835
      Engage the 3 claws and 2 guides, and then install the centering jig.

      NOTICE:
      1. The centering jig cannot be reused.
      2. Do not remove the centering jig before installing the rear wiper link pivot.

    3. E152621
      Close the glass hatch, and engage the 2 claws and guide.

      NOTICE:
      Be sure to engage the 2 claws and guide securely.

    4. E151099
      Disconnect the connector.

    5. Remove the 2 nuts.

    6. Remove the 4 bolts and the rear wiper motor assembly.

      NOTICE:
      1. Do not hold the rear wiper motor assembly by the rear wiper link pivot.
      2. Be careful not to scratch the back door glass.

  1. When using a new rear wiper motor assembly:

    1. E150159
      Disconnect the connector.

    2. Remove the 4 bolts.

    3. E150183
      Remove the 2 nuts and the rear wiper motor assembly.

      NOTICE:
      Be careful not to scratch the back door glass.


18. REMOVE BACK WINDOW LOCK ASSEMBLY

  1. B173453
    Disconnect the connector.

  1. Disengage the clamp.

  1. B173454
    Remove the 3 bolts.

  1. B173455
    Disengage the clip and remove the back window lock assembly.

← REMOVAL (May 2007 – Jun 2010)INSPECTION (from May 2007) →