2007-2013 Highlander Kluger · Service Manual SECURITIES

REMOVAL

Removal / installation · Vehicles built from Jul 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (w/ Navigation System for HDD)

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


2. REMOVE CENTER INSTRUMENT PANEL REGISTER ASSEMBLY

  1. B168368E01
    Apply protective tape to the areas shown in the illustration.

  1. Using a moulding remover, disengage the 2 claws and 5 clips, and then remove the center instrument panel register assembly as shown in the illustration.


3. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (w/o Smart Entry and Start System)

  1. B184678E01
    Apply protective tape to the areas shown in the illustration.

  1. Using a moulding remover, disengage the 10 claws and 8 clips starting from the upper part of the center instrument cluster finish panel assembly.

    NOTICE:
    Do not pull on the small storage compartment lid. Doing so may cause damage.

  1. Disconnect each connector and remove the center instrument cluster finish panel assembly.


4. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (w/ Smart Entry and Start System)

  1. B184680E01
    Apply protective tape to the areas shown in the illustration.

  1. Using a moulding remover, disengage the 10 claws and 8 clips starting from the upper part of the center instrument cluster finish panel assembly.

    NOTICE:
    Do not pull on the small storage compartment lid. Doing so may cause damage.

  1. Disconnect each connector and remove the center instrument cluster finish panel assembly.


5. REMOVE HEATER CONTROL AND ACCESSORY ASSEMBLY (for Manual Air Conditioning System)

  1. E150368
    Disengage the 4 clips and remove the heater control and accessory assembly.

  1. Disconnect the connector.


6. REMOVE AIR CONDITIONING CONTROL ASSEMBLY (for Automatic Air Conditioning System)

  1. E150367
    Disengage the 4 clips and remove the air conditioning control assembly.

  1. Disconnect the connector.


7. REMOVE RADIO RECEIVER ASSEMBLY WITH BRACKET (w/ Radio Receiver)

  1. E150551
    Remove the 4 bolts.

  1. E150552
    Pull the radio receiver assembly with bracket toward the rear of the vehicle and disengage the 4 clips.

  1. Disconnect each connector and remove the radio receiver assembly with bracket.


8. REMOVE NAVIGATION RECEIVER ASSEMBLY WITH BRACKET (w/ Navigation System)

  1. E150544
    Remove the 4 bolts.

  1. E150545
    Pull the navigation receiver assembly with bracket toward the rear of the vehicle and disengage the 4 clips.

  1. Disconnect each connector and remove the navigation receiver assembly with bracket.


9. REMOVE INTEGRATION CONTROL AND PANEL ASSEMBLY WITH BRACKET (w/o Radio Receiver)

  1. B173010
    Remove the 4 bolts <D>.

  1. Disengage the 4 clips.

  1. Disconnect each connector and remove the integration control and panel assembly with bracket.


10. REMOVE INTEGRATION CONTROL AND PANEL ASSEMBLY (w/ Radio Receiver)

  1. E151584
    Disengage the claw and disconnect the connector.

  1. B170938
    Disengage the 2 clips and remove the integration control and panel assembly.


11. REMOVE NO. 1 RADIO BRACKET (w/ Navigation System)

  1. E150546
    Disengage the claw and disconnect the connector.

  1. E150548
    Remove the 6 screws and No. 1 radio bracket.


12. REMOVE NO. 2 RADIO BRACKET (w/ Navigation System)

  1. E150547
    Remove the 6 screws and No. 2 radio bracket.


13. REMOVE NAVIGATION RECEIVER ASSEMBLY (w/ Navigation System)

14. REMOVE RADIO TUNER OPENING COVER WITH BRACKET (w/o Radio Receiver)
  1. Remove the 2 screws and the radio tuner opening cover with bracket from the integration control and panel assembly.


15. REMOVE INTEGRATION CONTROL AND PANEL ASSEMBLY (w/o Radio Receiver)
← REMOVAL (Aug 2008 – Jun 2010)INSPECTION (from May 2007) →