2007-2013 Highlander Kluger · Service Manual BODY ELECTRICAL

REMOVAL

Removal / installation · Vehicles built from Jul 2010


1. PRECAUTION (w/ Navigation System for HDD)
(Click here)

NOTICE:
After the ignition switch is turned off, the navigation receiver assembly (HDD navigation system) records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 60 seconds before disconnecting the cable from the negative (-) battery terminal.


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (w/ Navigation System for HDD)

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


3. REMOVE CENTER INSTRUMENT PANEL REGISTER ASSEMBLY

  1. B168368E01
    Apply protective tape to the areas shown in the illustration.

  1. Using a moulding remover, disengage the 2 claws and 5 clips, and then remove the center instrument panel register assembly as shown in the illustration.


4. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (w/o Smart Entry and Start System)

  1. B184678E01
    Apply protective tape to the areas shown in the illustration.

  1. Using a moulding remover, disengage the 10 claws and 8 clips starting from the upper part of the center instrument cluster finish panel assembly.

    NOTICE:
    Do not pull on the small storage compartment lid. Doing so may cause damage.

  1. Disconnect each connector and remove the center instrument cluster finish panel assembly.


5. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (w/ Smart Entry and Start System)

  1. B184680E01
    Apply protective tape to the areas shown in the illustration.

  1. Using a moulding remover, disengage the 10 claws and 8 clips starting from the upper part of the center instrument cluster finish panel assembly.

    NOTICE:
    Do not pull on the small storage compartment lid. Doing so may cause damage.

  1. Disconnect each connector and remove the center instrument cluster finish panel assembly.


6. REMOVE HEATER CONTROL AND ACCESSORY ASSEMBLY (for Manual Air Conditioning System)

  1. E150368
    Disengage the 4 clips and remove the heater control and accessory assembly.

  1. Disconnect the connector.


7. REMOVE AIR CONDITIONING CONTROL ASSEMBLY (for Automatic Air Conditioning System)

  1. E150367
    Disengage the 4 clips and remove the air conditioning control assembly.

  1. Disconnect the connector.


8. REMOVE RADIO RECEIVER ASSEMBLY WITH BRACKET (w/ Radio Receiver)

  1. E150551
    Remove the 4 bolts.

  1. E150552
    Pull the radio receiver assembly with bracket toward the rear of the vehicle and disengage the 4 clips.

  1. Disconnect each connector and remove the radio receiver assembly with bracket.


9. REMOVE NAVIGATION RECEIVER ASSEMBLY WITH BRACKET (w/ Navigation System)

  1. E150544
    Remove the 4 bolts.

  1. E150545
    Pull the navigation receiver assembly with bracket toward the rear of the vehicle and disengage the 4 clips.

  1. Disconnect each connector and remove the navigation receiver assembly with bracket.


10. REMOVE MULTI-MEDIA INTERFACE ECU WITH BRACKET

  1. E210927
    Disconnect each connector.

  1. E210928
    Remove the 3 nuts and multi-media interface ECU with bracket.


11. REMOVE NO. 1 MULTI-MEDIA INTERFACE BRACKET

  1. E210929
    Remove the 2 screws and No. 1 multi-media interface bracket.


12. REMOVE NO. 2 MULTI-MEDIA INTERFACE BRACKET

  1. E210930
    Remove the 2 screws and No. 2 multi-media interface bracket.


13. REMOVE MULTI-MEDIA INTERFACE ECU
← COMPONENTS (from Jul 2010)INSTALLATION (from Jul 2010) →