REMOVAL
Removal / installation · Vehicles built from Jul 2010
Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010
- HINT:
- Use the same procedures for the LH side and RH side.
- The following procedure is for the LH side.
- If the sensor rotor needs to be replaced, replace it together with the outboard joint shaft assembly.
(Click here)
(Click here)
| 1.
DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
 |
- NOTICE:
- When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).
| 2.
REMOVE REAR DOOR SCUFF PLATE LH
|
 |
- Disengage the 5 claws, 3 clips and guide, and remove the rear door scuff plate LH.
| 3.
REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH
|
 |
- Remove the rear door opening trim weatherstrip LH.
| 4.
REMOVE DECK BOARD ASSEMBLY
|
 |
- Remove the deck board assembly.
| 5.
REMOVE NO. 3 DECK BOARD SUB-ASSEMBLY
|
 |
- Disengage the 2 guides and remove the No. 3 deck board sub-assembly.
| 6.
REMOVE NO. 2 DECK BOARD SUB-ASSEMBLY
|
 |
- Disengage the 2 guides and remove the No. 2 deck board sub-assembly.
| 7.
REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)
|
 |
Remove the tonneau cover assembly.
| 8.
REMOVE REAR NO. 1 FLOOR BOARD (w/o Rear No. 2 Seat)
|
 |
- Disengage the 3 clips and 3 guides, and remove the rear No. 1 floor board.
| 9.
REMOVE REAR SEAT SIDE COVER LH (w/ Rear No. 2 Seat)
|
 |
- Disengage the 2 clips and remove the rear seat side cover LH.
| 10.
REMOVE DECK SIDE TRIM BOX LH
|
 |
- Remove the 2 deck side trim clips and clip.
Remove the deck side trim box LH as shown in the illustration.


| 11.
REMOVE REAR SEAT SIDE COVER RH (w/ Rear No. 2 Seat)
|
 |
- Disengage the 2 clips and remove the rear seat side cover RH.
| 12.
REMOVE JACK CARRIER SUPPORT |
|
| 13.
REMOVE JACK CARRIER CUSHION (for LHD)
|
 |
- Remove the jack carrier cushion.
| 14.
REMOVE JACK CARRIER CUSHION (for RHD)
|
 |
- Remove the jack carrier cushion.
| 15.
REMOVE JACK ASSEMBLY (for LHD)
|
 |
- Remove the jack assembly.
| 16.
REMOVE JACK ASSEMBLY (for RHD)
|
 |
- Remove the jack assembly.
| 17.
REMOVE JACK CARRIER ASSEMBLY (for LHD)
|
 |
- Using a screwdriver, disengage the 3 claws and remove the jack carrier assembly.
| 18.
REMOVE JACK CARRIER ASSEMBLY (for RHD)
|
 |
- Using a screwdriver, disengage the 3 claws and remove the jack carrier assembly.
| 19.
REMOVE DECK SIDE TRIM BOX RH
|
 |
- Remove the 2 deck side trim clips and clip.
Remove the deck side trim box RH as shown in the illustration.


| 20.
REMOVE DECK FLOOR BOARD ASSEMBLY (w/o Rear No. 2 Seat)
|
 |
- Remove the 4 bolts and 4 nuts.
Remove the deck floor board assembly.
| 21.
REMOVE REAR MAT
|
 |
- Remove the rear mat.
| 22.
REMOVE DECK FLOOR BOARD ASSEMBLY (w/ Rear No. 2 Seat)
|
 |
- Disengage the 3 claws.
Remove the 2 nuts and deck floor board assembly.
| 23.
REMOVE REAR DECK FLOOR BOX (w/o Rear No. 2 Seat)
|
 |
- Remove the 2 nuts and the deck floor box.
| 24.
DISCONNECT REAR NO. 2 SEAT OUTER BELT ASSEMBLY LH (w/ Rear No. 2 Seat)
|
 |
- Remove the bolt and disconnect the rear No. 2 seat outer belt assembly LH.
| 25.
DISCONNECT REAR NO. 2 SEAT OUTER BELT ASSEMBLY RH (w/ Rear No. 2 Seat)
|
 |
- HINT:
- Use the same procedure as for the LH side.
| 26.
REMOVE CENTER SEAT CUSHION COVER SUB-ASSEMBLY (w/ Rear No. 2 Seat)
|
 |
- Disengage the 2 claws <A>.
Disengage the 2 claws <B> and remove the center seat cushion cover sub-assembly.
| 27.
REMOVE REAR NO. 2 SEAT ASSEMBLY (w/ Rear No. 2 Seat)
|
 |
Remove the bolt on the front of the seat.


Remove the 6 bolts on the rear of the seat and the rear No. 2 seat assembly.


| 28.
REMOVE REAR FLOOR FINISH PLATE
|
 |
- Disengage the 4 clips and 4 claws, and remove the rear floor finish plate.
| 29.
REMOVE DECK SIDE TRIM COVER NO.2
|
 |
- Using a screwdriver, disengage the 2 claws and remove the deck side trim cover LH.
- HINT:
- Tape the screwdriver tip before use.
| 30.
REMOVE DECK SIDE TRIM LH
|
 |
- Remove the bolt.
- Disengage the 4 claws and 3 guides, and remove the deck side trim LH as shown in the illustration.
| 31.
REMOVE SIDE TRIM COVER LH
|
 |
- Disengage the 10 claws and remove the side trim cover LH.
| 32.
REMOVE REAR COMBINATION LIGHT SERVICE COVER LH
|
 |
- Using a screwdriver, disengage the 6 claws and 2 guides, and remove the rear combination light service cover LH.
- HINT:
- Tape the screwdriver tip before use.
| 33.
REMOVE REAR POWER POINT SOCKET ASSEMBLY
|
 |
Disconnect the connector.
- Disengage the claw and remove the rear power point socket assembly.
| 34.
REMOVE REAR POWER OUTLET SOCKET COVER
|
 |
- Disengage the 2 claws and remove the rear power outlet socket cover.
| 35.
REMOVE REAR DECK TRIM COVER (w/o Remote Folding Function)
|
 |
- Disengage the 10 claws and remove the rear deck trim cover.
| 36.
REMOVE RECLINING REMOTE CONTROL LEVER BEZEL LH (w/ Remote Folding Function)
|
 |
- Disengage the 5 claws and remove the reclining remote control lever bezel LH.
| 37.
REMOVE ROPE HOOK ASSEMBLY (for LH Side)
|
 |
- for Front Side:
Using a screwdriver, disengage the 2 claws.
- HINT:
- Tape the screwdriver tip before use.
Remove the bolt and rope hook assembly.
- for Rear Side:
Using a screwdriver, disengage the 2 claws.
- HINT:
- Tape the screwdriver tip before use.
Remove the bolt and rope hook assembly.
| 38.
REMOVE NO. 2 DECK SIDE TRIM HOOK
|
 |
- Remove the screw and No. 2 deck side trim hook.
| 39.
REMOVE FRONT DECK SIDE TRIM COVER LH
|
 |
- Using a screwdriver, disengage the 4 claws and remove the 2 front deck side trim covers LH.
- HINT:
- Tape the screwdriver tip before use.
| 40.
DISCONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY LH
|
 |
- Remove the bolt and disconnect the floor end of the rear No. 1 seat outer belt assembly.
| 41.
REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH
|
 |
Remove the 2 bolts.
Remove the 2 clips.
Disengage the 7 claws and 4 clips, and remove the deck trim side panel assembly LH.


| 43.
REMOVE REAR SPEED SENSOR |
 |
- Disconnect the rear speed sensor connector.
- Disconnect the grommet of the rear speed sensor wire from the hole of the wheel house.
Remove the 2 bolts, No. 1 clamp and No. 2 clamp from the body and absorber.
- Remove the bolt and rear speed sensor body from the carrier.
- NOTICE:
- Keep the sensor tip and rear speed sensor installation hole free from foreign matter.