Disengage the 4 claws and 4 clips, and remove the instrument cluster finish panel assembly.
11.
REMOVE COMBINATION METER ASSEMBLY
Remove the 4 screws <F>.
Disconnect the connector and remove the combination meter assembly.
12.
REMOVE CENTER INSTRUMENT PANEL REGISTER ASSEMBLY
Apply protective tape to the areas shown in the illustration.
Using a moulding remover, disengage the 2 claws and 5 clips, and then remove the center instrument panel register assembly as shown in the illustration.
13.
REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY
Apply protective tape to the areas shown in the illustration.
Using a moulding remover, disengage the 10 claws and 8 clips starting from the upper part of the center instrument cluster finish panel assembly.
NOTICE:
Do not pull on the small storage compartment lid. Doing so may cause damage.
Disconnect each connector and remove the center instrument cluster finish panel assembly.
14.
REMOVE HEATER CONTROL AND ACCESSORY ASSEMBLY
Disengage the 4 clips and remove the heater control and accessory assembly.
Disconnect the connector.
15.
REMOVE RADIO RECEIVER ASSEMBLY WITH BRACKET
Remove the 4 bolts.
Pull the radio receiver assembly with bracket toward the rear of the vehicle and disengage the 4 clips.
Disconnect each connector and remove the radio receiver assembly with bracket.
16.
REMOVE FRONT DOOR SCUFF PLATE LH
Disengage the 8 claws and guide, and remove the front door scuff plate LH.
17.
REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH
Remove the clip.
Disengage the clip and claw, and remove the cowl side trim sub-assembly LH.
Remove the No. 2 console box duct as shown in the illustration.
25.
REMOVE LOWER REAR CONSOLE BOX
Remove the lower rear console box.
26.
REMOVE CONSOLE BOX ASSEMBLY (w/o Rear Air Conditioning System)
Remove the 4 bolts and 2 screws.
Disengage the 6 claws and remove the console box assembly.
27.
REMOVE CONSOLE BOX ASSEMBLY (w/ Rear Air Conditioning System)
Remove the 4 bolts and 2 screws.
Disconnect the connector.
Disengage the 6 claws, and remove the console box assembly.
28.
REMOVE FRONT NO. 1 CONSOLE BOX INSERT
Using a clip remover, remove the 2 clips.
Remove the 3 screws <F>.
Disengage the claw and 2 guides, and then remove the front No. 1 console box insert.
29.
REMOVE FRONT NO. 2 CONSOLE BOX INSERT
Using a clip remover, remove the clip.
Remove the 3 screws <F>.
Disengage the claw and 2 guides, and then remove the front No. 2 console box insert.
30.
DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH
31.
REMOVE FRONT PILLAR GARNISH LH
Pull the upper part of the garnish toward the inside of the cabin and disengage the 2 clips.
Cut off the clip <A>.
Disengage the 3 guides and remove the front pillar garnish LH.
Remove the clip <A>.
Protect the curtain shield airbag assembly.
Cover the airbag with a 700 mm (27.56 in.) x 120 mm (4.72 in.) cloth or piece of nylon and fix the ends of the cover with tape, as shown in the illustration.
NOTICE:
Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.
32.
DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH
33.
REMOVE FRONT PILLAR GARNISH RH
Pull the upper part of the garnish toward the inside of the cabin and disengage the 2 clips.
Cut off the clip <A>.
Disengage the 3 guides and remove the front pillar garnish RH.
Remove the clip <A>.
Protect the curtain shield airbag assembly.
Cover the airbag with a 700 mm (27.56 in.) x 120 mm (4.72 in.) cloth or piece of nylon and fix the ends of the cover with tape, as shown in the illustration.
NOTICE:
Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.