2007-2013 Highlander Kluger · Service Manual BODY ELECTRICAL

REMOVAL

Removal / installation · Vehicles built Aug 2008 – Jun 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010


1. PRECAUTION
(Click here)

2. POSITION FRONT WHEELS STRAIGHT AHEAD

3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait for 90 seconds after disconnecting the cable to prevent airbag deployment (Click here).

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


4. REMOVE LOWER NO. 3 STEERING WHEEL COVER

  1. C165090
    Disengage the claw and remove the lower No. 3 steering wheel cover.


5. REMOVE LOWER NO. 2 STEERING WHEEL COVER

  1. C165091
    Disengage the claw and remove the lower No. 2 steering wheel cover.


6. REMOVE STEERING PAD

  1. C166981E01
    Using a "TORX" socket wrench (T30), loosen the 2 "TORX" screws until the groove along the screw circumference catches on the screw case.

  1. C165092
    Pull out the steering pad from the steering wheel assembly and support the steering pad with one hand as shown in the illustration.

    NOTICE:
    When removing the steering pad, do not pull the airbag wire harness.

  1. C165094E01
    Disconnect the horn connector from the steering pad.

  1. Using a screwdriver with the tip wrapped with protective tape, disconnect the 2 airbag connectors and remove the steering pad.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.


7. REMOVE STEERING WHEEL ASSEMBLY

  1. C165708E01
    Remove the steering wheel assembly set nut.

  1. Put matchmarks on the steering wheel assembly and the steering main shaft.

  1. Disconnect the connectors from the spiral cable.

  1. C165709E01
    Using SST, remove the steering wheel assembly.
    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)

    NOTICE:
    Apply a small amount of grease to the threads and tip of SST (09953-05020) before use.


8. REMOVE STEERING COLUMN COVER

  1. C165715
    Remove the 2 screws.

  1. C166128
    Disengage the 2 claws to remove the lower steering column cover.

  1. C165716
    Disengage the claw to remove the upper steering column cover.


9. REMOVE TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY
  1. Disconnect the connectors from the turn signal switch assembly with spiral cable sub-assembly.

  1. C166129
    Using pliers, grip the claws of the clip and remove the turn signal switch assembly with spiral cable sub-assembly.


10. REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY

  1. B168364
    Disengage the 4 claws and 4 clips, and remove the instrument cluster finish panel assembly.


11. REMOVE COMBINATION METER ASSEMBLY

  1. B168365
    Remove the 4 screws <F>.

  1. Disconnect the connector and remove the combination meter assembly.


12. REMOVE CENTER INSTRUMENT PANEL REGISTER ASSEMBLY

  1. B168368E01
    Apply protective tape to the areas shown in the illustration.

  1. Using a moulding remover, disengage the 2 claws and 5 clips, and then remove the center instrument panel register assembly as shown in the illustration.


13. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY

  1. B184678E01
    Apply protective tape to the areas shown in the illustration.

  1. Using a moulding remover, disengage the 10 claws and 8 clips starting from the upper part of the center instrument cluster finish panel assembly.

    NOTICE:
    Do not pull on the small storage compartment lid. Doing so may cause damage.

  1. Disconnect each connector and remove the center instrument cluster finish panel assembly.


14. REMOVE HEATER CONTROL AND ACCESSORY ASSEMBLY

  1. E150368
    Disengage the 4 clips and remove the heater control and accessory assembly.

  1. Disconnect the connector.


15. REMOVE RADIO RECEIVER ASSEMBLY WITH BRACKET

  1. E150551
    Remove the 4 bolts.

  1. E150552
    Pull the radio receiver assembly with bracket toward the rear of the vehicle and disengage the 4 clips.

  1. Disconnect each connector and remove the radio receiver assembly with bracket.


16. REMOVE FRONT DOOR SCUFF PLATE LH

  1. B173224
    Disengage the 8 claws and guide, and remove the front door scuff plate LH.


17. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH

  1. B173227
    Remove the clip.

  1. Disengage the clip and claw, and remove the cowl side trim sub-assembly LH.


18. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY

  1. B168371
    Remove the 2 bolts <B>.

  1. Disengage the 3 claws and 10 clips.

  1. Disconnect each connector.

  1. Disconnect the hood lock control cable assembly and remove the lower instrument panel finish panel sub-assembly.


19. REMOVE FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedure for the RH side and the LH side.


20. REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:
Use the same procedure for the RH side and the LH side.


21. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

  1. B172999
    Disengage the 3 claws.

  1. Disengage the 2 guides and remove the No. 2 instrument panel under cover sub-assembly.


22. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY

  1. B168370
    Remove the 2 bolts <B> and 3 screws <F>.

  1. Disengage the 4 claws and 3 clips.

  1. Disconnect each connector and clamp, and remove the lower instrument panel sub-assembly.


23. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY

  1. B168372
    Disengage the 4 claws and 4 clips.

  1. Disconnect the connector and remove the upper console panel sub-assembly.


24. REMOVE NO. 2 CONSOLE BOX DUCT (w/o Rear Air Conditioning System)

  1. B173012
    Remove the No. 2 console box duct as shown in the illustration.


25. REMOVE LOWER REAR CONSOLE BOX
  1. Remove the lower rear console box.


26. REMOVE CONSOLE BOX ASSEMBLY (w/o Rear Air Conditioning System)

  1. B173628
    Remove the 4 bolts and 2 screws.

  1. B173629
    Disengage the 6 claws and remove the console box assembly.


27. REMOVE CONSOLE BOX ASSEMBLY (w/ Rear Air Conditioning System)

  1. B181135
    Remove the 4 bolts and 2 screws.

  1. B175149
    Disconnect the connector.

  1. Disengage the 6 claws, and remove the console box assembly.


28. REMOVE FRONT NO. 1 CONSOLE BOX INSERT

  1. B168373
    Using a clip remover, remove the 2 clips.

  1. Remove the 3 screws <F>.

  1. Disengage the claw and 2 guides, and then remove the front No. 1 console box insert.


29. REMOVE FRONT NO. 2 CONSOLE BOX INSERT

  1. B168374
    Using a clip remover, remove the clip.

  1. Remove the 3 screws <F>.

  1. Disengage the claw and 2 guides, and then remove the front No. 2 console box insert.


30. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH

31. REMOVE FRONT PILLAR GARNISH LH

  1. B173222E01
    Pull the upper part of the garnish toward the inside of the cabin and disengage the 2 clips.

  1. Cut off the clip <A>.

  1. Disengage the 3 guides and remove the front pillar garnish LH.

  1. Remove the clip <A>.

  1. B173225E01
    Protect the curtain shield airbag assembly.

    1. Cover the airbag with a 700 mm (27.56 in.) x 120 mm (4.72 in.) cloth or piece of nylon and fix the ends of the cover with tape, as shown in the illustration.

      NOTICE:
      Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.


32. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH

33. REMOVE FRONT PILLAR GARNISH RH

  1. B173682E01
    Pull the upper part of the garnish toward the inside of the cabin and disengage the 2 clips.

  1. Cut off the clip <A>.

  1. Disengage the 3 guides and remove the front pillar garnish RH.

  1. Remove the clip <A>.

  1. B173684E01
    Protect the curtain shield airbag assembly.

    1. Cover the airbag with a 700 mm (27.56 in.) x 120 mm (4.72 in.) cloth or piece of nylon and fix the ends of the cover with tape, as shown in the illustration.

      NOTICE:
      Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.


34. REMOVE NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY

  1. B168375
    Disengage the 2 claws and 2 clips.

  1. Disengage the 2 guides and remove the No. 1 instrument panel speaker panel sub-assembly.


35. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY (for LH Side)

  1. E150560
    Remove the 2 bolts and front No. 2 speaker assembly.

  1. Disconnect the connector.


36. REMOVE NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY

  1. B173014
    Disengage the 2 claws and 2 clips.

  1. Disengage the 2 guides and remove the No. 2 instrument panel speaker panel sub-assembly.


37. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY (for RH Side)

HINT:
Use the same procedure for the RH side and the LH side.


38. DISCONNECT INSTRUMENT PANEL WIRE ASSEMBLY

  1. C165103
    Disconnect the connector.


39. REMOVE INSTRUMENT PANEL SAFETY PAD ASSEMBLY
  1. Disconnect each connector.

  1. Remove the bolt <E>.

  1. Remove the 2 passenger airbag bolts <A>.

  1. Disengage each clamp.

    B173015E01

  1. Remove the 2 clips.

  1. Remove the 2 bolts <D> and nut <H>.

  1. Disengage the 5 claws and remove the instrument panel safety pad assembly.

    B168377E01


40. REMOVE NO. 1 HEATER TO REGISTER DUCT

  1. B168378
    Remove the 3 screws <F> and the No. 1 heater to register duct.


41. REMOVE NO. 4 HEATER TO REGISTER DUCT

  1. B168379
    Remove the 3 screws <F> and the No. 4 heater to register duct.


42. REMOVE SIDE NO. 1 DEFROSTER NOZZLE DUCT

  1. B168380
    Remove the screw <F> and the side No. 1 defroster nozzle duct.


43. REMOVE SIDE NO. 2 DEFROSTER NOZZLE DUCT

  1. B168381
    Remove the screw <F> and the side No. 2 defroster nozzle duct.


44. REMOVE DEFROSTER NOZZLE ASSEMBLY

  1. B173016
    Remove the clip.

  1. Remove the 3 screws <F> and the defroster nozzle assembly.


45. REMOVE CENTER HEATER TO REGISTER SUB DUCT

  1. B168382
    Remove the 2 screws <F> and the center heater to register sub duct.


46. REMOVE ANTENNA CORD SUB-ASSEMBLY

  1. Disengage the 9 clamps and remove the antenna cord sub-assembly.

    E150566


47. REMOVE ENGINE UNDER COVER ASSEMBLY

  1. A171849
    Remove the 2 bolts and engine under cover assembly RR.

  1. A171850
    Remove the 2 bolts, 2 screws, 5 clips and engine under cover assembly.


48. REMOVE NO. 1 ENGINE UNDER COVER

  1. A171855
    Remove the 6 bolts, 2 clips and No. 1 engine under cover.


49. REMOVE FRONT FENDER MOULDING SUB-ASSEMBLY

HINT:
Use the same procedure for the RH side and the LH side (Click here).


50. REMOVE FRONT FENDER LINER

  1. B174753E01
    Remove the screw.

  1. Using a screwdriver, turn the pin 90 degrees and remove the pin hold clip.

  1. B174750
    Using a 4 mm hexagon wrench, remove the 2 screws.

  1. Remove the 2 grommets.

    HINT:
    The grommets need to be replaced with new ones because they will break when they are removed.

  1. B174752
    Remove the 5 clips, 7 screws and front fender liner RH.


51. REMOVE PULL TOP ANTENNA POLE SUB-ASSEMBLY

  1. E151125
    Remove the pull top antenna pole sub-assembly by turning it in the direction of the arrow shown in the illustration.


52. REMOVE ANTENNA NUT

  1. E151126
    Remove the antenna nut.


53. REMOVE FENDER ANTENNA ASSEMBLY
  1. Roll up part of the insulator.

  1. E151128
    Disengage the 3 clamps.

  1. E151129
    Remove the nut and fender antenna assembly.


54. REMOVE ANTENNA ORNAMENT

  1. E151127
    Remove the antenna ornament.

← REMOVAL (May 2007 – Jul 2008)INSTALLATION (May 2007 – Jul 2008) →