2007-2013 Highlander Kluger · Service Manual BODY

INSTALLATION

Removal / installation · Vehicles built May 2007 – Jul 2008

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010


1. REPAIR INSTRUCTION
  1. Clean the vehicle body surface.

    1. Using a heat light, heat the vehicle body surface.

      Heating temperature:
      Item
      Temperature
      Vehicle Body
      40 to 60°C (104 to 140°F)

      NOTICE:
      Do not heat the vehicle body excessively.

    2. Wipe off any tape adhesive residue with cleaner.

  1. Installation temperature

    1. When the ambient temperature is below 15°C (59°F), perform the installation procedure after warming the vehicle body surface (installation surface of the door frame) and tape up to between 20 and 30°C (68 and 86°F) using a heat light. When the ambient temperature is above 35°C (95°F), cool the vehicle body surface (installation surface of the door frame) and tape down to between 20 and 30°C (68 and 86°F) prior to installation.

      HINT:
      1. The most appropriate temperature for installing the tape is 25°C (77°F).
      2. When the temperature is low, the tape turns stiff and comes off easily. When the temperature is high, the tape looses elasticity.

  1. Before installation

    1. Remove any roughness of coating and dirt on and around the vehicle body surface where the tape will be installed (installation surface of the door frame). If any roughness or dirt remains when pressing the tape onto the surface, air will be trapped under the tape and result in a poor appearance.

      HINT:
      Spray water on the shop floor to settle any dust.

  1. Key points for handling the tape

    1. The tape bends and rolls up easily. Store the tape between flat pieces of cardboard or other similar objects and keep it dry and level.

      NOTICE:
      Do not bend the tape or leave it in high temperature places.

  1. Key points for installation of the tape (how to use a squeegee and installation procedure for flat surfaces)

    NOTICE:
    1. Position the tape accurately to achieve a neat finish and to avoid peeling.
    2. The tape cannot be reused because it deforms and will not fit any more after being removed.


    1. To avoid air bubbles, slightly raise the part of the tape that is going to be applied so that its adhesive surface does not touch the vehicle body while applying the tape. Tilt the squeegee at 40 to 50° (for pressing forward) or 30 to 45° (for pulling) to the vehicle body surface and press the tape onto the vehicle body surface with a force of 20 to 30 N (2 to 3 kgf) at a constant slow speed of 3 to 7 cm (1.2 to 2.8 in.) per second.

      B147252E02

      NOTICE:
      Be sure to observe the specified pressing speed, force, and angle of the squeegee to avoid wrinkles or air bubbles.

      HINT:
      1. Either angle of the squeegee (for pressing forward or for pulling) is acceptable.
      2. Be sure to apply the tape while removing the release paper 10 to 20 mm (0.393 to 0.787 in.) from the edge of the squeegee.

  1. Key points for installation of the tape (how to use a squeegee and installation procedure for hemming surfaces)

    1. B147253E01
      If it is difficult to apply the tape, install it in several steps as shown in the illustration. Use your fingers or the padded surface of a squeegee to slowly apply the tape to the hem of the vehicle, especially for a small hem.

      HINT:
      When applying tape to the backside of a hem, remove the release paper and use your fingers or the padded surface of a squeegee.

  1. Key points for installation of the tape (how to use a squeegee and installation procedure for corners)

    1. Remove the release paper and apply the tape carefully with your fingers.

    2. Before applying the tape to each corner, heat the tape using a heat light and gradually apply it, avoiding wrinkles on the tape to achieve a neat finish.

  1. Check after installation

    1. After completing the application, check if the tape is applied neatly. If the tape is not applied neatly, reapply using new tape.

      NOTICE:
      Do not reuse the tape.


2. INSTALL INNER REAR BLACK OUT FRONT DOOR TAPE

  1. B174414E01
    Referring to the illustration, position the inner rear black out front door tape.

  1. Remove the release paper and apply the tape.


3. INSTALL INNER UPPER BLACK OUT FRONT DOOR TAPE

  1. B174413E01
    Referring to the illustration, position the inner upper black out front door tape.

  1. Remove the release paper and apply the tape.


4. INSTALL NO. 1 BLACK OUT TAPE

  1. B174412E01
    Referring to the illustration, position the No. 1 black out tape.

    Standard measurement:
    Dimension
    Measurement
    A
    2 to 4 mm (0.079 to 0.157 in.)
    B
    4 to 6 mm (0.157 to 0.236 in.)

  1. Remove the release paper and apply the tape.


5. INSTALL FRONT DOOR WEATHERSTRIP

  1. B174901
    Install the front door weatherstrip.


6. INSTALL DOOR FRAME GARNISH

  1. B172947
    Engage a new clip and install the door frame garnish.


7. INSTALL FRONT DOOR BELT MOULDING ASSEMBLY

  1. B172792
    Engage the 6 claws and install the front door belt moulding assembly.


8. INSTALL FRONT DOOR GLASS RUN

  1. B172946
    Install the front door glass run.


9. INSTALL FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY
  1. Apply MP grease to the sliding parts of the front door window regulator sub-assembly.

  1. B172943E02
    Install the temporary bolt to the front door window regulator sub-assembly.

  1. Temporarily install the window regulator.

  1. Tighten the 6 bolts in the order shown in the illustration to install the front window regulator.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }


10. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY

  1. B172972E01
    Insert the front door glass sub-assembly into the front door panel along the front door glass run as indicated in the order of the arrows in the illustration.

  1. B172941
    Install the front door glass sub-assembly with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. B172940
    Install the hole plug.


11. INSTALL FRONT DOOR SERVICE HOLE COVER
  1. Apply butyl tape to the front door panel.

  1. Pass the front door lock remote control cable and rear door inside the locking cable through a new front door service hole cover.

  1. B172973E01
    Attach the front door service hole cover according to the reference points on the front door panel.

    NOTICE:
    Securely install the front door service hole cover avoiding wrinkles and air bubbles.

  1. B172939
    Connect each connector.

  1. Engage the 2 clamps.


12. INSTALL OUTER REAR VIEW MIRROR ASSEMBLY WITH COVER

  1. B173465E01
    Engage the claw, and temporarily install the outer rear view mirror assembly with cover.

  1. Tighten the 3 nuts in the order shown in the illustration to install the outer rear view mirror assembly with cover.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. B173464
    Engage the clamp and connect the connector.

  1. Install the clip.


13. INSTALL FRONT NO. 1 SPEAKER ASSEMBLY

  1. E150556
    Install the front No. 1 speaker assembly with the 4 bolts.

    NOTICE:
    Do not touch the cone part of the speaker.

  1. Connect the connector.


14. INSTALL FRONT DOOR INNER GLASS WEATHERSTRIP

  1. B172938
    Install the front door inner glass weatherstrip.


15. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY
  1. Connect the connector.

  1. B172935
    Connect the front door lock remote control cable and front door inside locking cable to the front door inside handle sub-assembly.

  1. Engage the 2 clamps.

  1. B172933
    Engage the front door trim board with the 5 claws on the front door inner glass weatherstrip.

  1. Engage the 9 clips.

  1. B172932E01
    Install the 2 screws <B>.

  1. Install the screw <A> and front door trim board to the front door panel.

    Torque:
    3.5 N*m{ 36 kgf*cm , 31 in.*lbf }


16. INSTALL COURTESY LIGHT ASSEMBLY
  1. Connect the connector.

  1. B172930
    Engage the claw and install the courtesy light assembly.


17. INSTALL ASSIST GRIP COVER

  1. B172925
    Engage the 4 claws and install the assist grip cover.


18. INSTALL FRONT ARMREST UPPER BASE PANEL
  1. Connect the connector.

  1. B172923
    Engage the 7 claws and clip and install the front armrest upper base panel.


19. INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG

  1. B172921
    Engage the 3 claws and install the front door inside handle bezel plug.


20. INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH

  1. B172931
    Engage the clip and claw, and install the front door lower frame bracket garnish.


21. CONNECT NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


22. INITIALIZE WINDOW CONTROL SYSTEM (for Driver Side)
(Click here)
← REMOVAL (from Jul 2010)INSTALLATION (Aug 2008 – Jun 2010) →