2007-2013 Highlander Kluger · Service Manual BODY

REMOVAL

Removal / installation · Vehicles built from Jul 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010


1. DISCONNECT NEGATIVE BATTERY TERMINAL

CAUTION:
Wait for 90 seconds after disconnecting the terminal to prevent airbag deployment (Click here).

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


2. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH

  1. B172931
    Disengage the claw and clip, and remove the front door lower frame bracket garnish.


3. REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG

  1. B172920E01
    Using a screwdriver with the tip wrapped with protective tape, disengage the 3 claws, and remove the front door inside handle bezel plug.


4. REMOVE FRONT ARMREST UPPER BASE PANEL

  1. B172922E01
    Using a screwdriver with the tip wrapped with protective tape, disengage the 7 claws and clip, and remove the front armrest upper base panel.

  1. Disconnect the connector.


5. REMOVE ASSIST GRIP COVER

  1. B174183E01
    Using a screwdriver with the tip wrapped with protective tape, disengage the 4 claws and remove the assist grip cover.


6. REMOVE COURTESY LIGHT ASSEMBLY

  1. B172929E01
    Using a screwdriver with the tip wrapped with protective tape, disengage the claw and remove the courtesy light assembly.

  1. Disconnect the connector.


7. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY

  1. B172932
    Remove the 3 screws.

  1. B172933
    Using a clip remover, disengage the 9 clips.

  1. Disengage the 5 claws and separate the front door trim board sub-assembly from the front door inner glass weatherstrip.

  1. B172934
    Disengage the 2 clamps.

  1. Disconnect the front door lock remote control cable and front door inside locking cable.

  1. Disconnect the connector.


8. REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP

  1. B172938
    Remove the front door inner glass weatherstrip from the front door panel.


9. REMOVE FRONT NO. 1 SPEAKER ASSEMBLY

  1. E150556
    Disconnect the connector.

  1. Remove the 4 bolts and front No. 1 speaker assembly.

    NOTICE:
    Do not touch the cone part of the speaker.


10. REMOVE OUTER REAR VIEW MIRROR ASSEMBLY WITH COVER

  1. B173464E01
    Disconnect the connector and clamp.

  1. Disengage the clip.

  1. B173465
    Remove the 3 nuts.

  1. Disengage the claw and remove the outer rear view mirror assembly with cover.


11. REMOVE FRONT DOOR SERVICE HOLE COVER

  1. B172939
    Disconnect the each connector and 2 clamps, and remove the front door service hole cover.

    HINT:
    Remove the remaining butyl tape on the door side.


12. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY

  1. B172940
    Remove the hole plug.

  1. Connect the negative battery terminal.

  1. Connect the power window regulator motor connector.

  1. Connect the power window regulator master switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.

  1. Disconnect the negative battery terminal and power window regulator master switch assembly.

  1. Disconnect the power window regulator motor connector.

  1. B172941
    Remove the 2 bolts.

    NOTICE:
    After the bolts are removed, do not allow the door to fall.

  1. B172942E01
    Remove the front door glass sub-assembly as shown in the illustration.

    NOTICE:
    Do not damage the door glass.


13. REMOVE FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY

  1. B172943E01
    Loosen the temporary bolt.

    NOTICE:
    Do not remove the temporary bolt. If the temporary bolt is removed, the front door window regulator may fall and cause damage.

  1. Remove the 5 bolts.

  1. Remove the front door window regulator sub-assembly and the front power window regulator motor assembly as a unit.

  1. Remove the temporary bolt from the front door window regulator sub-assembly.


14. REMOVE FRONT DOOR GLASS RUN

  1. B172946
    Remove the front door glass run.


15. REMOVE FRONT DOOR BELT MOULDING ASSEMBLY

  1. B172791E01
    Put protective tape around the front door belt moulding assembly.

  1. B172792
    Disengage the 6 claws and remove the front door belt moulding assembly.

    NOTICE:
    Be careful when removing the moulding as there are claws attached to the front and rear ends of the moulding.


16. REMOVE DOOR FRAME GARNISH

  1. B172947
    Disengage the clip and remove the door frame garnish.

    HINT:
    This clip needs to be replaced with a new one because the clip will break when removing the door frame garnish.


17. REMOVE FRONT DOOR WEATHERSTRIP

  1. B174901
    Remove the upper part of the front door weatherstrip to the extent that allows removal of the black out tape.


18. REMOVE NO. 1 BLACK OUT TAPE
  1. Using a heat light, heat the No. 1 black out tape and vehicle body.

    Heating temperature:
    Item
    Temperature
    Vehicle Body
    40 to 60°C (104 to 140°F)

    NOTICE:
    Do not heat the vehicle body excessively.

  1. Pull back an end of the No. 1 black out tape and pull it parallel to the vehicle body to pull it off.


19. REMOVE INNER UPPER BLACK OUT FRONT DOOR TAPE
  1. Using a heat light, heat the inner upper black out front door tape and vehicle body.

    Heating temperature:
    Item
    Temperature
    Vehicle Body
    40 to 60°C (104 to 140°F)

    NOTICE:
    Do not heat the vehicle body excessively.

  1. Pull back an end of the inner upper black out front door tape and pull it parallel to the vehicle body to pull it off.


20. REMOVE INNER REAR BLACK OUT FRONT DOOR TAPE
  1. Using a heat light, heat the inner rear black out front door tape and vehicle body.

    Heating temperature:
    Item
    Temperature
    Vehicle Body
    40 to 60°C (104 to 140°F)

    NOTICE:
    Do not heat the vehicle body excessively.

  1. Pull back an end of the inner rear black out front door tape and pull it parallel to the vehicle body to pull it off.

← REMOVAL (Aug 2008 – Jun 2010)INSTALLATION (May 2007 – Jul 2008) →