2007-2013 Highlander Kluger · Service Manual BODY

Back Door Closer does not Operate

Circuit diagnosis · Vehicles built Aug 2008 – Jun 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

When the back door closer does not operate, one of the following may be the cause 1) improper fit of back door, or a foreign object is stuck in back door, or 2) initialization of the power back door ECU, or a malfunction in the 3) power back door ECU power source circuit, or 4) back door lock circuit, or 5) power back door ECU.

WIRING DIAGRAM

B165216E03

INSPECTION PROCEDURE


1. CHECK BACK DOOR LOCK FUNCTION
  1. Check if the back door is fully closed by hand.



NG
IMPROPER FIT OF BACK DOOR, OR A FOREIGN OBJECT IS STUCK IN BACK DOOR
OK


2. INITIALIZE POWER BACK DOOR ECU
  1. Check that the power back door drive unit (power back door ECU) can be initialized (Click here).


NEXT


3. CHECK BACK DOOR CLOSER SYSTEM
  1. Check that the back door closer system operation.

    OK:
    Back door closer system operates normally.



NG
Go to step 4
OK

END

4. CHECK DTC OUTPUT
  1. Check for the DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC is not output
    A
    B2250 is output
    B
    B2251 is output
    C



B
GO TO DTC CHART (B2250) (Click here)

C
GO TO DTC CHART (B2251) (Click here)
A


5. INSPECT FUSE (ECU IG NO. 1, ECU-B)
  1. Remove the ECU IG No. 1 fuse from the instrument panel junction block and ECU-B fuse from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    ECU IG NO. 1
    Always
    Below 1 Ω
    ECU-B
    Always
    Below 1 Ω



NG
REPLACE FUSE
OK


6. CHECK FUSIBLE LINK BLOCK ASSEMBLY (PBD FUSE)
  1. Remove the fusible link block assembly.

  1. B165197E02
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A - B
    Always
    Below 1 Ω

    HINT:
    PBD 30A fuse is located in the fusible link block assembly.



NG
REPLACE FUSIBLE LINK BLOCK ASSEMBLY
OK


7. CHECK HARNESS AND CONNECTOR (BODY GROUND)
  1. Disconnect the O14 power back door ECU connector.

  1. B165208E07
    Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    O14-8 (IG) - Body ground
    Ignition switch on (IG)
    11 to 14 V
    O14-10 (ECUB) - Body ground
    Always
    11 to 14 V
    O14-12 (B) - Body ground
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8. CHECK HARNESS AND CONNECTOR (POWER SOURCE)
  1. Disconnect the O14 power back door ECU connector.

  1. B165208E08
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    O14-11 (GND) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9. INSPECT BACK DOOR LOCK
B143899E07
  1. Remove the back door lock. (Click here)

  1. Apply battery voltage and check operation of the door lock motor.

    OK:
    Measurement Condition
    Specified Condition
    Battery positive (+) → Terminal 1 (DC+)
    Battery negative (-) → Terminal 2 (DC-)
    Latch turns to full-latch position
    Battery positive (+) → Terminal 2 (DC-)
    Battery negative (-) → Terminal 1 (DC+)
    Latch turns to open-latch position

  1. Measure the resistance of the switch.

    Standard resistance:
    Full-latch switch:
    Tester Connection
    Door Lock Latch Position
    Specified Condition
    5 (HAF) - 4 (GND)
    Over-latch
    Below 1 Ω
    5 (HAF) - 4 (GND)
    Open-latch
    10 kΩ or higher
    5 (HAF) - 4 (GND)
    Full-latch
    10 kΩ or higher
    5 (HAF) - 4 (GND)
    Half-latch
    10 kΩ or higher
    Back door courtesy light switch:
    Tester Connection
    Door Lock Latch Position
    Specified Condition
    3 (BDCY) - 4 (GND)
    Open-latch
    Below 1 Ω
    3 (BDCY) - 4 (GND)
    Half-latch
    Below 1 Ω
    3 (BDCY) - 4 (GND)
    Full-latch
    10 kΩ or higher
    3 (BDCY) - 4 (GND)
    Over-latch
    10 kΩ or higher



NG
REPLACE BACK DOOR LOCK (Click here)
OK


10. CHECK HARNESS AND CONNECTOR (BACK DOOR LOCK - POWER BACK DOOR ECU AND BODY GROUND)

  1. B165204E07
    Disconnect the T4 door lock connector.

  1. Disconnect the O14 ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    T4-1 (DC+) - O14-2 (DC+)
    Always
    Below 1 Ω
    T4-2 (DC-) - O14-1 (DC-)
    Always
    Below 1 Ω
    T4-5 (HAF) - O14-22 (HAF)
    Always
    Below 1 Ω
    T4-6 (POS) - O14-24 (POS)
    Always
    Below 1 Ω
    T4-3 (BDCY) - O14-20 (FUL)
    Always
    Below 1 Ω
    T4-4 (GND) - Body ground
    Always
    Below 1 Ω
    T4-1 (DC+) - Body ground
    Always
    10 kΩ or higher
    T4-2 (DC-) - Body ground
    Always
    10 kΩ or higher
    T4-5 (HAF) - Body ground
    Always
    10 kΩ or higher
    T4-6 (POS) - Body ground
    Always
    10 kΩ or higher
    T4-3 (BDCY) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE POWER BACK DOOR DRIVE UNIT (POWER BACK DOOR ECU)


← Back Door Closer does not Operate (May 2007 – Jul 2008)Back Door Closer does not Operate (from Jul 2010) →