Back Door Closer does not Operate
Circuit diagnosis · Vehicles built from Jul 2010
Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010
DESCRIPTION
When the back door closer does not operate, one of the following may be the cause 1) improper fit of back door, or a foreign object is stuck in back door, or 2) initialization of the power back door ECU, or a malfunction in the 3) power back door ECU power source circuit, or 4) back door lock circuit, or 5) power back door ECU.WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. CHECK BACK DOOR LOCK FUNCTION |
Check if the back door is fully closed by hand.
|
|
||||
| OK | |
| 2. INITIALIZE POWER BACK DOOR ECU |
Check that the power back door drive unit (power back door ECU) can be initialized (Click here).
| NEXT | |
| 3. CHECK BACK DOOR CLOSER SYSTEM |
Check that the back door closer system operation.
- OK:
- Back door closer system operates normally.
|
|
||||
| OK | ||
| ||
| 4. CHECK DTC OUTPUT |
Check for the DTCs (Click here).
- Result:
Result
Proceed to
DTC is not output
A
B2250 is output
B
B2251 is output
C
|
|
||||
|
|
||||
| A | |
| 5. INSPECT FUSE (ECU IG NO. 1, ECU-B) |
Remove the ECU IG No. 1 fuse from the instrument panel junction block and ECU-B fuse from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
ECU IG NO. 1
Always
Below 1 Ω
ECU-B
Always
Below 1 Ω
|
|
||||
| OK | |
| 6. CHECK FUSIBLE LINK BLOCK ASSEMBLY (PBD FUSE) |
Remove the fusible link block assembly.
Measure the resistance according to the value(s) in the table below.

- Standard resistance:
Tester Connection
Condition
Specified Condition
A - B
Always
Below 1 Ω
- HINT:
- PBD 30A fuse is located in the fusible link block assembly.
|
|
||||
| OK | |
| 7. CHECK HARNESS AND CONNECTOR (BODY GROUND) |
Disconnect the O14 power back door ECU connector.
Measure the voltage according to the value(s) in the table below.

- Standard voltage:
Tester Connection
Condition
Specified Condition
O14-8 (IG) - Body ground
Ignition switch on (IG)
11 to 14 V
O14-10 (ECUB) - Body ground
Always
11 to 14 V
O14-12 (B) - Body ground
Always
11 to 14 V
|
|
||||
| OK | |
| 8. CHECK HARNESS AND CONNECTOR (POWER SOURCE) |
Disconnect the O14 power back door ECU connector.
Measure the resistance according to the value(s) in the table below.

- Standard resistance:
Tester Connection
Condition
Specified Condition
O14-11 (GND) - Body ground
Always
Below 1 Ω
|
|
||||
| OK | |
| 9. INSPECT BACK DOOR LOCK |


Remove the back door lock. (Click here)
Apply battery voltage and check operation of the door lock motor.
- OK:
Measurement Condition
Specified Condition
Battery positive (+) → Terminal 1 (DC+)
Battery negative (-) → Terminal 2 (DC-)
Latch turns to full-latch position
Battery positive (+) → Terminal 2 (DC-)
Battery negative (-) → Terminal 1 (DC+)
Latch turns to open-latch position
Measure the resistance of the switch.
- Standard resistance:
- Full-latch switch:
Tester Connection
Door Lock Latch Position
Specified Condition
5 (HAF) - 4 (GND)
Over-latch
Below 1 Ω
5 (HAF) - 4 (GND)
Open-latch
10 kΩ or higher
5 (HAF) - 4 (GND)
Full-latch
10 kΩ or higher
5 (HAF) - 4 (GND)
Half-latch
10 kΩ or higher
- Back door courtesy light switch:
Tester Connection
Door Lock Latch Position
Specified Condition
3 (BDCY) - 4 (GND)
Open-latch
Below 1 Ω
3 (BDCY) - 4 (GND)
Half-latch
Below 1 Ω
3 (BDCY) - 4 (GND)
Full-latch
10 kΩ or higher
3 (BDCY) - 4 (GND)
Over-latch
10 kΩ or higher
|
|
||||
| OK | |
| 10. CHECK HARNESS AND CONNECTOR (BACK DOOR LOCK - POWER BACK DOOR ECU AND BODY GROUND) |
Disconnect the T4 door lock connector.

Disconnect the O14 ECU connector.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
T4-1 (DC+) - O14-2 (DC+)
Always
Below 1 Ω
T4-2 (DC-) - O14-1 (DC-)
Always
Below 1 Ω
T4-5 (HAF) - O14-22 (HAF)
Always
Below 1 Ω
T4-6 (POS) - O14-24 (POS)
Always
Below 1 Ω
T4-3 (BDCY) - O14-20 (FUL)
Always
Below 1 Ω
T4-4 (GND) - Body ground
Always
Below 1 Ω
T4-1 (DC+) - Body ground
Always
10 kΩ or higher
T4-2 (DC-) - Body ground
Always
10 kΩ or higher
T4-5 (HAF) - Body ground
Always
10 kΩ or higher
T4-6 (POS) - Body ground
Always
10 kΩ or higher
T4-3 (BDCY) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | ||
| ||
