Home › BODY › ENGINE HOOD / DOOR › BACK DOOR CLOSER SYSTEM
Back Door cannot be Opened
Circuit diagnosis · Vehicles built May 2007 – Jul 2008
Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010
DESCRIPTION
When the back door cannot be opened, one of the following may be malfunctioning: 1) power back door drive unit (power back door ECU), or 2) back door lock, or 3) back door open switch, or 4) main body ECU (instrument panel junction block). WIRING DIAGRAM
INSPECTION PROCEDURE
1. READ VALUE ON INTELLIGENT TESTER
Check the Data List to determine if the back door lock function properly.
Back Door (Power back door ECU)
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Door Lock Status
Back door lock condition signal / LOCK or UNLOCK
LOCK: Back door is locked UNLOCK: Back door is unlocked
-
OK:
The back door functions as specified in the normal condition.
NG
OK
2. READ VALUE ON INTELLIGENT TESTER
Check the Data List to determine if the back door handle switch function properly.
Main body ECU (Instrument panel junction block)
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Back Door Open Handle SW
Back door opener switch / ON or OFF
ON: Back door opener switch is pushed OFF: Back door opener switch is not pushed
-
OK:
The back door opener switch functions as specified in the normal condition.
NG
OK
3. INSPECT BACK DOOR LOCK
Remove the back door lock (Click here ).
Apply battery voltage and check operation of the door lock motor.
OK:
Measurement Condition
Specified Condition
Battery positive (+) → Terminal 1 (DC+) Battery negative (-) → Terminal 2 (DC-)
Latch turns to full-latch position
Battery positive (+) → Terminal 2 (DC-) Battery negative (-) → Terminal 1 (DC+)
Latch turns to open-latch position
Measure the resistance of the switch.
Standard resistance:
Full-latch switch:
Tester Connection
Door Lock Latch Position
Specified Condition
5 (HAF) - 4 (GND)
Over-latch
Below 1 Ω
5 (HAF) - 4 (GND)
Open-latch
10 kΩ or higher
5 (HAF) - 4 (GND)
Full-latch
10 kΩ or higher
5 (HAF) - 4 (GND)
Half-latch
10 kΩ or higher
Sector switch:
Tester Connection
Door Lock Latch Position
Specified Condition
6 (POS) - 4 (GND)
Open-latch
Below 1 Ω
6 (POS) - 4 (GND)
Over-latch
10 kΩ or higher
6 (POS) - 4 (GND)
Full-latch
10 kΩ or higher
6 (POS) - 4 (GND)
Half-latch
10 kΩ or higher
Back door courtesy light switch:
Tester Connection
Door Lock Latch Position
Specified Condition
3 (BDCY) - 4 (GND)
Open-latch
Below 1 Ω
3 (BDCY) - 4 (GND)
Half-latch
Below 1 Ω
3 (BDCY) - 4 (GND)
Full-latch
10 kΩ or higher
3 (BDCY) - 4 (GND)
Over-latch
10 kΩ or higher
NG
OK
4. CHECK HARNESS AND CONNECTOR (BACK DOOR LOCK - POWER BACK DOOR ECU)
Disconnect the T4 back door lock connector.
Disconnect the O14 ECU connector.
Measure the resistance according to the value(s) in the table below.
Standard resistance:
Tester Connection
Condition
Specified Condition
T4-1 (DC+) - O14-2 (DC+)
Always
Below 1 Ω
T4-2 (DC-) - O14-1 (DC-)
Always
Below 1 Ω
T4-5 (HAF) - O14-22 (HAF)
Always
Below 1 Ω
T4-6 (POS) - O14-24 (POS)
Always
Below 1 Ω
T4-3 (BDCY) - O14-20 (FUL)
Always
Below 1 Ω
T4-4 (GND) - Body ground
Always
Below 1 Ω
T4-1 (DC+) - Body ground
Always
10 kΩ or higher
T4-2 (DC-) - Body ground
Always
10 kΩ or higher
T4-5 (HAF) - Body ground
Always
10 kΩ or higher
T4-6 (POS) - Body ground
Always
10 kΩ or higher
T4-3 (BDCY) - Body ground
Always
10 kΩ or higher
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
REPLACE POWER BACK DOOR DRIVE UNIT (POWER BACK DOOR ECU) (Click here )
5. INSPECT BACK DOOR OPENER SWITCH
Remove the back door opener switch (Click here ).
Measure the resistance according to the value(s) in the table below.
Standard resistance:
Tester Connection
Switch Position
Specified Condition
2 - 3
Back door opener switch not pushed (OFF)
10 kΩ or higher
2 - 3
Back door opener switch pushed (ON)
Below 1 Ω
NG
OK
6. CHECK HARNESS AND CONNECTOR (BACK DOOR OPENER SWITCH - MAIN BODY ECU)
Disconnect the h1 switch connection.
Disconnect the D8 ECU connector.
Measure the resistance according to the value(s) in the table below.
Standard resistance:
Tester Connection
Condition
Specified Condition
h1-3 (BDSU) - D8-26 (BDSU)
Always
Below 1 Ω
h1-2 (L) - Body ground
Always
Below 1 Ω
h1-3 (BDSU) - Body ground
Always
10 kΩ or higher
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK)
7. REPLACE POWER BACK DOOR DRIVE UNIT (POWER BACK DOOR ECU)
Replace the power back door drive unit (power back door ECU) (Click here ).
NEXT
8. CHECK POWER BACK DOOR DRIVE UNIT (POWER BACK DOOR ECU)
Check that the back door closer operates normally.
OK:
It operates normally.
NG
REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK)
OK
END (REPLACE POWER BACK DOOR DRIVE UNIT (POWER BACK DOOR ECU) DEFECTIVE)