2007-2013 Highlander Kluger · Service Manual BODY

Power Back Door cannot be Opened or Closed Using the Power Back Door Switch

Circuit diagnosis · Vehicles built Aug 2008 – Jun 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

When the power back door cannot be opened or closed using the power back door switch, one of the following may be malfunctioning: 1) power back door opener / closer switch circuit, 2) power back door drive unit (power back door ECU), or 3) main body ECU (instrument panel junction block).

WIRING DIAGRAM

B165218E04

INSPECTION PROCEDURE


1. READ VALUE ON INTELLIGENT TESTER
  1. Check the Data List to determine if the power back door opener/closer switch function properly.

    Main body ECU (Instrument panel junction block) 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Back Door Open SW
    Back door opener/closer switch / ON or OFF
    ON: Back door opener/closer switch is pushed
    OFF: Back door opener/closer switch is not pushed
    -

    OK:
    The power back door opener/closer switch functions as specified in the normal condition.



NG
Go to step 4
OK


2. REPLACE POWER BACK DOOR DRIVE UNIT (POWER BACK DOOR ECU)
  1. Replace the power back door drive unit (power back door ECU) (Click here).


NEXT


3. CHECK POWER BACK DOOR DRIVE UNIT (POWER BACK DOOR ECU)
  1. Check that the power back door operates normally.

    OK:
    It operates normally.



NG
REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK)
OK

END (REPLACE POWER BACK DOOR DRIVE UNIT (POWER BACK DOOR ECU) DEFECTIVE)

4. INSPECT POWER BACK DOOR OPENER / CLOSER SWITCH

  1. B165199E01
    Remove the power back door opener/closer switch (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Position
    Specified Condition
    4 - 1
    Power back door opener/closer switch not pushed (OFF)
    10 kΩ or higher
    4 - 1
    Power back door opener/closer switch pushed (ON)
    Below 1 Ω



NG
REPLACE POWER BACK DOOR OPENER / CLOSER SWITCH (Click here)
OK


5. CHECK HARNESS AND CONNECTOR (POWER BACK DOOR OPENER/CLOSER SWITCH - MAIN BODY ECU)

  1. B165210E02
    Disconnect the D38 switch connector.

  1. Disconnect the D7 ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D38-4 (CSW) - D7-2 (PBDS)
    Always
    Below 1 Ω
    D38-1 (E) - Body ground
    Always
    Below 1 Ω
    D38-4 (CSW) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. REPLACE POWER BACK DOOR DRIVE UNIT (POWER BACK DOOR ECU)
  1. Replace the power back door drive unit (power back door ECU) (Click here).


NEXT


7. CHECK POWER BACK DOOR ECU
  1. Check that the power back door operates normally.

    OK:
    It operates normally.



NG
REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK)
OK

END (REPLACE POWER BACK DOOR DRIVE UNIT (POWER BACK DOOR ECU) DEFECTIVE)


← Power Back Door cannot be Opened or Closed Using the Power Back Door Switch (May 2007 – Jul 2008)Power Back Door cannot be Opened or Closed Using the Power Back Door Switch (from Jul 2010) →