Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › SEAT POSITION SENSOR

SEAT POSITION SENSOR > INSTALLATION

for Preparation Click here



1. INSTALL SEAT POSITION SENSOR


    C168034
  1. Install the seat position sensor to the seat slide position sensor protector with the pin as shown in the illustration.



    C107067E10
  1. Using a 1.3 mm (0.051 in.) feeler gauge, temporarily install the seat position sensor.

    NOTICE:
    1. If the seat position sensor has been dropped, or there are any cracks, dents or other defects in the case or connector, replace the seat position sensor with a new one.
    2. When installing the seat position sensor, be careful that the SRS wiring does not interfere with other parts and that it is not pinched between other parts.

    HINT:
    Be sure that the clearance between the seat position sensor and the seat rail is within 0.6 mm (0.024 in.) to 2.0 mm (0.079 in.).



    C166974
  1. Using a "TORX" socket wrench (T30), tighten the "TORX" screw to install the seat position sensor.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Make sure that the clearance between the seat position sensor and the seat rail is within 0.6 mm (0.024 in.) to 2.0 mm (0.079 in.).

  1. Connect the connector.

  1. Check that there are no loose parts after installing the seat position sensor.



2. INSTALL FRONT SEAT ASSEMBLY LH (for Manual Seat)
  1. Place the front seat assembly in the cabin.

    NOTICE:
    Be careful not to damage the vehicle body.

  1. Connect the connectors under the seat.

  1. Temporarily install the front seat assembly with the 4 bolts.

  1. Lift up the seat track adjusting handle and move the seat to the rearmost position.



    B174588E01
  1. Tighten the 2 bolts on the front side of the seat.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

    HINT:
    Tighten the bolts in the order indicated in the illustration.

  1. Lift up the seat track adjusting handle and move the seat to the foremost position.



    B174587E01
  1. Tighten the 2 bolts on the rear side of the seat.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

    HINT:
    Tighten the bolts in the order indicated in the illustration.



3. INSPECT FRONT SEAT SLIDE ADJUSTER LOCK (for Manual Seat)
  1. During sliding operation of the front seat, check that the left and right adjusters move together smoothly and lock simultaneously.
    If the seat adjusters do not lock simultaneously, loosen the bolts securing the seat to adjust the adjuster position.



4. INSTALL REAR SEAT TRACK COVER LH (for Manual Seat)


    B180417
  1. Engage the 4 claws and install the 2 rear seat track covers.



5. INSTALL FRONT INNER SEAT TRACK COVER LH (for Manual Seat)
  1. Lift up the seat track adjusting handle and move the seat to the rearmost position.



    B174584
  1. Engage the 2 claws and install the front inner seat track cover.



6. INSTALL FRONT OUTER SEAT TRACK COVER LH (for Manual Seat)


    B174583
  1. Engage the 2 claws and install the front outer seat track cover.



7. INSTALL FRONT SEAT HEADREST ASSEMBLY LH (for Manual Seat)


    B176350
  1. Install the front seat headrest assembly as shown in the illustration.



8. INSTALL FRONT SEAT ASSEMBLY LH (for Power Seat)
  1. Place the front seat assembly in the cabin.

    NOTICE:
    Be careful not to damage the vehicle body.

  1. Connect the connectors under the seat.

  1. Connect the cable to the negative (-) battery terminal.

    NOTICE:
    When reconnected the cable, some systems need to be initialized (Click here).

  1. Temporarily install the front seat assembly with the 4 bolts.

  1. Operate the power seat switch knob and move the seat to the rearmost position.



    B174582E01
  1. Tighten the 2 bolts on the front side of the seat.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

    HINT:
    Tighten the bolts in the order indicated in the illustration.

  1. Operate the power seat switch knob and move the seat to the foremost position.



    B174581E01
  1. Tighten the 2 bolts on the rear side of the seat.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

    HINT:
    Tighten the bolts in the order indicated in the illustration.



9. INSTALL REAR INNER SEAT TRACK COVER LH (for Power Seat)


    B172844
  1. Engage the 2 claws and install the rear inner seat track cover.



10. INSTALL REAR OUTER SEAT TRACK COVER LH (for Power Seat)


    B172843
  1. Engage the 2 claws and install the rear outer seat track cover.



11. INSTALL FRONT INNER SEAT TRACK COVER LH (for Power Seat)
  1. Operate the power seat switch knob and move the seat to the rearmost position.



    B172842
  1. Engage the 2 claws and install the front inner seat track cover.



12. INSTALL FRONT OUTER SEAT TRACK COVER LH (for Power Seat)


    B172841
  1. Engage the 2 claws and install the front outer seat track cover.



13. INSTALL FRONT SEAT HEADREST ASSEMBLY LH (for Power Seat)


    B176350
  1. Install the front seat headrest assembly as shown in the illustration.



14. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (for Manual Seat)

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



15. INSPECT FRONT SEAT ASSEMBLY (for Power Seat)
  1. Inspect the power seat operation.

  1. w/ Seat Heater System:
    Check the seat heater operation.

    1. Turn the ignition switch on (IG).

    2. Turn the seat heater switch on.

    3. Wait 5 minutes or more and confirm that the seat surface becomes warm.



16. INSPECT SRS WARNING LIGHT
  1. Inspect the SRS warning light (Click here).