Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › SEAT POSITION SENSOR

SEAT POSITION SENSOR > REMOVAL

for Preparation Click here



1. PRECAUTION

CAUTION:
Be sure to read "PRECAUTION" thoroughly before servicing (Click here).



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (for Manual Seat)

CAUTION:
Wait for at least 90 seconds after disconnecting the cable to prevent airbag deployment.

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



3. REMOVE FRONT SEAT HEADREST ASSEMBLY LH (for Manual Seat)


    B176347
  1. Press the headrest support button and pull up the headrest to its highest position as shown in the illustration.



    B176348
  1. Insert a finger or screwdriver into the hole to release the lock. Pull the headrest up as shown in the illustration to remove it.



4. REMOVE FRONT OUTER SEAT TRACK COVER LH (for Manual Seat)
  1. Lift up the seat track adjusting handle and move the seat to the rearmost position.



    B174583
  1. Disengage the 2 claws and remove the front outer seat track cover.



5. REMOVE FRONT INNER SEAT TRACK COVER LH (for Manual Seat)


    B174584
  1. Disengage the 2 claws and remove the front inner seat track cover.



6. REMOVE REAR SEAT TRACK COVER LH (for Manual Seat)
  1. Lift up the seat track adjusting handle and move the seat to the foremost position.



    B180417
  1. Disengage the 4 claws and remove the 2 rear seat track covers.



7. REMOVE FRONT SEAT ASSEMBLY LH (for Manual Seat)


    B174587
  1. Remove the 2 bolts on the rear side of the seat.

  1. Lift up the seat track adjusting handle and move the seat to the rearmost position.



    B174588
  1. Remove the 2 bolts on the front side of the seat.

  1. Lift up the seat track adjusting handle and move the seat to the center position. Also, operate the reclining adjuster release handle and move the seatback to the upright position.

  1. Disconnect the connectors under the front seat assembly.

  1. Remove the front seat assembly.

    NOTICE:
    Be careful not to damage the vehicle body.



8. REMOVE FRONT SEAT HEADREST ASSEMBLY LH (for Power Seat)


    B176347
  1. Press the headrest support button and pull up the headrest to its highest position as shown in the illustration.



    B176348
  1. Insert a finger or screwdriver into the hole to release the lock. Pull the headrest up as shown in the illustration to remove it.



9. REMOVE FRONT OUTER SEAT TRACK COVER LH (for Power Seat)
  1. Operate the power seat switch knob and move the seat to the rearmost position.



    B172841
  1. Disengage the 2 claws and remove the front outer seat track cover.



10. REMOVE FRONT INNER SEAT TRACK COVER LH (for Power Seat)


    B172842
  1. Disengage the 2 claws and remove the front inner seat track cover.



11. REMOVE REAR OUTER SEAT TRACK COVER LH (for Power Seat)
  1. Operate the power seat switch knob and move the seat to the foremost position.



    B172843
  1. Disengage the 2 claws and remove the rear outer seat track cover.



12. REMOVE REAR INNER SEAT TRACK COVER LH (for Power Seat)


    B172844
  1. Disengage the 2 claws and remove the rear inner seat track cover.



13. REMOVE FRONT SEAT ASSEMBLY LH (for Power Seat)


    B174581
  1. Remove the 2 bolts on the rear side of the seat.

  1. Operate the power seat switch knob and move the seat to the rearmost position.



    B174582
  1. Remove the 2 bolts on the front side of the seat.

  1. Operate the power seat switch knob and move the seat to the center position. Also, Operate the power seat switch knob and move the seatback to the upright position.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent the airbag and seat belt pretensioner from deploying (Click here).

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Disconnect each connector under the front seat assembly.

  1. Remove the front seat assembly.

    NOTICE:
    Be careful not to damage the vehicle body.



14. REMOVE SEAT POSITION SENSOR


    C166974
  1. Disconnect the connector.

  1. Using a "TORX" socket wrench (T30), remove the "TORX" screw and seat position sensor with the seat slide position sensor protector.



    C133892
  1. Remove the seat position sensor from the seat slide position sensor protector as shown in the illustration.