FRONT AIRBAG SENSOR > INSTALLATION |
| 1. INSTALL FRONT AIRBAG SENSOR |
Check that the ignition switch is off.
Check that the battery negative (-) cable is disconnected.
![]() |
Temporarily install the front airbag sensor with the 2 claws and pin.
Install the front airbag sensor with the 2 bolts.
Check that there are no loose parts after installing the front airbag sensor.
Connect the connector to the front airbag sensor.
| 2. INSTALL HEADLIGHT ASSEMBLY |
Connect the connectors.
![]() |
Engage the clamp.
![]() |
Engage the claw and install the headlight assembly with the bolt and 2 screws.
| 3. INSTALL REAR FENDER SPLASH SHIELD SUB-ASSEMBLY |
![]() |
Engage the 3 clips and 3 guides, and install the rear fender splash shield sub-assembly.
| 4. INSTALL FRONT BUMPER ASSEMBLY (w/o Fog Light) |
![]() |
Engage the 4 claws and install the front bumper assembly.
![]() |
Install the clip and 7 screws.
![]() |
Install the screw and pin hold clip.
| 5. INSTALL FRONT BUMPER ASSEMBLY (w/ Fog Light) |
Connect each fog light connector, and then install the front bumper assembly.
![]() |
Engage the 4 claws.
![]() |
Install the clip and 7 screws.
![]() |
Install the screw and pin hold clip.
| 6. INSTALL RADIATOR GRILLE |
![]() |
Engage the 4 guides and 6 claws, and install the radiator grille.
![]() |
Install the 4 clips and 2 bolts.
| 7. INSTALL COOL AIR INTAKE DUCT SEAL |
![]() |
Install the cool air intake duct seal with the 11 clips.
| 8. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 9. VEHICLE PREPARATION FOR HEADLIGHT AIMING ADJUSTMENT |
Prepare the vehicle:
| 10. PREPARATION FOR HEADLIGHT AIMING (Using a headlight aim test machine) |
Adjust the headlight aim in accordance with the headlight aim test machine instructions.
| 11. PREPARATION FOR HEADLIGHT AIMING (Using a Screen) |
![]() |
Prepare the vehicle:
Prepare a piece of thick white paper (approximately 2 m (6.6 ft.) (height) x 4 m (13.1 ft.) (width)) to use as a screen.
Draw a vertical line down the center of the screen (V line).
Set the screen as shown in the illustration.

![]() |
Draw base lines (H, V LH, and V RH lines) on the screen as shown in the illustration.
H Line (Headlight height):
Draw a horizontal line across the screen so that it passes through the center marks. The H line should be at the same height as the headlight bulb center marks of the low-beam headlights.
V LH Line, V RH Line (Center mark position of left-hand (LH) and right-hand (RH) headlights):
Draw two vertical lines so that they intersect the H line at each center mark (aligned with the center of the low-beam headlight bulbs).
| 12. INSPECT HEADLIGHT AIMING |
Cover the headlight or disconnect the connector of the headlight on the opposite side to prevent light from the headlight that is not being inspected from affecting the headlight aiming inspection.
Start the engine.
Turn on the headlight and check if the cutoff line matches the preferred cutoff line in the following illustration.

| 13. ADJUST HEADLIGHT AIMING |
![]() |
Adjust the aim vertically:
Adjust the aim of each headlight to the specified range by turning each aiming screw with a screwdriver.
| 14. VEHICLE PREPARATION FOR FOG LIGHT AIMING ADJUSTMENT (w/ Fog Light) |
Prepare the vehicle:
| 15. PREPARATION FOR FOG LIGHT AIMING (w/ Fog Light) |
![]() |
Prepare the vehicle:
Prepare a piece of thick white paper (approximately 2 m (6.6 ft.) (height) x 4 m (13.1 ft.) (width)) to use as a screen.
Draw a vertical line down the center of the screen (V line).
Set the screen as shown in the illustration.

![]() |
Draw base lines (H, V LH, and V RH lines) on the screen as shown in the illustration.
H Line (Fog light height):
Draw a horizontal line across the screen so that it passes through the center marks. The H line should be at the same height as the fog light bulb center marks of the fog lights.
V LH Line, V RH Line (Center mark position of left-hand (LH) and right-hand (RH) fog lights):
Draw two vertical lines so that they intersect the H line at each center mark aligned with the center of the fog light bulbs.
| 16. INSPECT FOG LIGHT AIMING (w/ Fog Light) |
Cover the fog light or disconnect the connector of the fog light on the opposite side to prevent light from the fog light that is not being inspected from affecting the fog light aiming inspection.
Start the engine.
Turn on the fog light and check if the cutoff line falls within the specified area in the following illustration.

| 17. ADJUST FOG LIGHT AIMING (w/ Fog Light) |
![]() |
Adjust the aim vertically:
Adjust the aim of each fog light to the specified range by turning each aiming screw with a screwdriver.
| 18. INSPECT SRS WARNING LIGHT |
Inspect the SRS warning light (Click here).