Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › CURTAIN SHIELD AIRBAG ASSEMBLY

CURTAIN SHIELD AIRBAG ASSEMBLY > REMOVAL

for Preparation Click here


HINT:
  1. Use the same procedure for the RH side and LH side.
  2. The procedures listed below are for the LH side.



1. PRECAUTION

CAUTION:
Be sure to read "PRECAUTION" thoroughly before servicing (Click here).



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait for at least 90 seconds after disconnecting the cable to prevent airbag deployment.

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



3. REMOVE REAR CENTER SEAT ASSEMBLY


4. REMOVE REAR SEAT HEADREST ASSEMBLY (for LH Side)


    B180411
  1. Press the headrest support button and pull up the headrest to its highest position as shown in the illustration.



    B180415
  1. Insert a finger or screwdriver into the hole to release the lock. Pull the headrest up as shown in the illustration to remove it.



5. REMOVE REAR SEAT TRACK BRACKET COVER LH


    B173775
  1. Disengage the 8 claws and remove the 2 rear seat track bracket covers.



6. REMOVE REAR OUTER TRACK BRACKET COVER LH


    B173776
  1. Disengage the 4 claws and remove the rear outer track bracket cover.



7. REMOVE REAR INNER TRACK BRACKET COVER LH


    B173777
  1. Disengage the 4 claws and remove the rear inner track bracket cover.



8. REMOVE REAR SEAT LEG SIDE COVER LH


    B173779
  1. Disengage the 3 claws.

  1. Disengage the clip and remove the rear seat leg side cover.



9. DISCONNECT REAR NO. 1 SEAT LOCK CABLE ASSEMBLY LH (w/ Remote Folding Function)


  1. Pull down the adjuster's lock piece to release the lock as shown in the illustration.


    B180388E01



    B174594E01
  1. Using a screwdriver wrapped with protective tape, disengage the 2 claws as shown in the illustration.



  1. Lift up the seat track adjusting handle to the uppermost position and hold the handle in this position as shown in the illustration.


    B173770E01

  1. Using a screwdriver wrapped with protective tape, disconnect the rear No. 1 seat lock cable assembly as shown in the illustration.



  1. Using a screwdriver wrapped with protective tape, disconnect the rear seat reclining control cable as shown in the illustration.


    B180393E01

  1. Secure the rear seat reclining control cable with the carpet hole as shown in the illustration.



10. REMOVE REAR NO. 1 SEAT ASSEMBLY LH


    B173780
  1. Remove the 3 bolts on the rear side of the seat.



    B173778
  1. Remove the 2 bolts on the front side of the seat and the rear No. 1 seat assembly.

    NOTICE:
    Be careful not to damage the vehicle body.



11. REMOVE REAR SEAT HEADREST ASSEMBLY (for RH Side)


    B180412
  1. Press the headrest support button and pull up the headrest to its highest position as shown in the illustration.



    B180416
  1. Insert a finger or screwdriver into the hole to release the lock. Pull the headrest up as shown in the illustration to remove it.



12. REMOVE REAR SEAT TRACK BRACKET COVER RH


    B173760
  1. Disengage the 8 claws and remove the 2 rear seat track bracket covers.



13. REMOVE REAR OUTER TRACK BRACKET COVER RH


    B204931
  1. Disengage the 5 claws and remove the rear outer track bracket cover.



14. REMOVE REAR INNER TRACK BRACKET COVER RH


    B173761
  1. Disengage the 4 claws and remove the rear inner track bracket cover.



15. REMOVE REAR SEAT LEG SIDE COVER RH


    B173765
  1. Disengage the 3 claws.

  1. Disengage the clip and remove the rear seat leg side cover.



16. DISCONNECT REAR NO. 1 SEAT LOCK CABLE ASSEMBLY RH (w/ Remote Folding Function)

HINT:
Use the same procedure for the RH side and the LH side.



17. REMOVE REAR NO. 1 SEAT ASSEMBLY RH


    B173774
  1. Remove the 3 bolts on the rear side of the seat.



    B173764
  1. Remove the 2 bolts on the front side of the seat and the rear No. 1 seat assembly.

    NOTICE:
    Be careful not to damage the vehicle body.



18. REMOVE FRONT DOOR SCUFF PLATE LH


    B173224
  1. Disengage the 8 claws and guide, and remove the front door scuff plate LH.



19. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH


    B173227
  1. Remove the clip.

  1. Disengage the clip and claw, and remove the cowl side trim sub-assembly LH.



20. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH


    B173234
  1. Remove the front door opening trim weatherstrip LH.



21. REMOVE FRONT PILLAR GARNISH LH


    B173222E01
  1. Pull the upper part of the garnish toward the inside of the cabin and disengage the 2 clips.

  1. Cut off the clip <A>.

  1. Disengage the 3 guides and remove the front pillar garnish LH.

  1. Remove the clip <A>.



    B173225E01
  1. Protect the curtain shield airbag assembly.

    1. Cover the airbag with a 700 mm (27.56 in.) x 120 mm (4.72 in.) cloth or piece of nylon and fix the ends of the cover with tape, as shown in the illustration.

      NOTICE:
      Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.



22. REMOVE REAR DOOR SCUFF PLATE LH


    B173228
  1. Disengage the 5 claws, 3 clips and guide, and remove the rear door scuff plate LH.



23. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH


    B173232
  1. Remove the rear door opening trim weatherstrip LH.



24. REMOVE LOWER CENTER PILLAR GARNISH LH


    B173230
  1. Disengage the 2 claws and 2 clips, and remove the lower center pillar garnish LH.



25. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH


    B170910
  1. Remove the bolt and disconnect the floor end of the front seat outer belt assembly.



26. REMOVE CENTER PILLAR GARNISH LH


    B173229
  1. Remove the screw and clip.

  1. Disengage the 2 guides and clip, and remove the center pillar garnish LH.



27. REMOVE FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedure for the RH side and the LH side.



28. REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:
Use the same procedure for the RH side and the LH side.



29. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:
Use the same procedure for the RH side and the LH side.



30. REMOVE FRONT PILLAR GARNISH RH


    B173682E01
  1. Pull the upper part of the garnish toward the inside of the cabin and disengage the 2 clips.

  1. Cut off the clip <A>.

  1. Disengage the 3 guides and remove the front pillar garnish RH.

  1. Remove the clip <A>.



    B173684E01
  1. Protect the curtain shield airbag assembly.

    1. Cover the airbag with a 700 mm (27.56 in.) x 120 mm (4.72 in.) cloth or piece of nylon and fix the ends of the cover with tape, as shown in the illustration.

      NOTICE:
      Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.



31. REMOVE REAR DOOR SCUFF PLATE RH

HINT:
Use the same procedure for the RH side and the LH side.



32. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH

HINT:
Use the same procedure for the RH side and the LH side.



33. REMOVE LOWER CENTER PILLAR GARNISH RH

HINT:
Use the same procedure for the RH side and the LH side.



34. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY RH

HINT:
Use the same procedure for the RH side and the LH side.



35. REMOVE CENTER PILLAR GARNISH RH

HINT:
Use the same procedure for the RH side and the LH side.



36. REMOVE DECK BOARD ASSEMBLY


    B173240
  1. Remove the deck board assembly.



37. REMOVE NO. 3 DECK BOARD SUB-ASSEMBLY


    B173242
  1. Disengage the 2 guides and remove the No. 3 deck board sub-assembly.



38. REMOVE NO. 2 DECK BOARD SUB-ASSEMBLY


    B173244
  1. Disengage the 2 guides and remove the No. 2 deck board sub-assembly.



39. REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)
  1. Remove the tonneau cover assembly.



40. REMOVE REAR NO. 1 FLOOR BOARD (w/o Rear No. 2 Seat)


    B175152
  1. Disengage the 3 clips and the 3 guides, and remove the rear No. 1 floor board.



41. REMOVE REAR SEAT SIDE COVER LH (w/ Rear No. 2 Seat)


    B173607
  1. Disengage the 2 clips and remove the rear seat side cover LH.



42. REMOVE DECK SIDE TRIM BOX LH


    B173243E01
  1. Remove the 2 deck side trim clips and clip.



  1. Remove the deck side trim box LH as shown in the illustration.


    B178554



43. REMOVE REAR SEAT SIDE COVER RH (w/ Rear No. 2 Seat)


    B173608
  1. Disengage the 2 clips and remove the rear seat side cover RH.



44. REMOVE JACK CARRIER SUPPORT


45. REMOVE JACK CARRIER CUSHION


    B178550
  1. Remove the jack carrier cushion.



46. REMOVE JACK ASSEMBLY


    B173245
  1. Remove the jack assembly.



47. REMOVE JACK CARRIER ASSEMBLY


    B178548
  1. Using a screwdriver, disengage the 3 claws and remove the jack carrier assembly.



48. REMOVE DECK SIDE TRIM BOX RH


    B173247E01
  1. Remove the 2 deck side trim clips and clip.



  1. Remove the deck side trim box RH as shown in the illustration.


    B178552



49. REMOVE DECK FLOOR BOARD ASSEMBLY (w/o Rear No. 2 Seat)


    B178560
  1. Remove the 4 bolts and 4 nuts.

  1. Remove the deck floor board assembly.



50. REMOVE REAR MAT


    B173249
  1. Remove the rear mat.



51. REMOVE DECK FLOOR BOARD ASSEMBLY (w/ Rear No. 2 Seat)


    B178561
  1. Disengage the 3 claws.

  1. Remove the 2 nuts and the deck floor board assembly.



52. REMOVE REAR DECK FLOOR BOX (w/o Rear No. 2 Seat)


    B173679
  1. Remove the 2 nuts and the deck floor box.



53. REMOVE NO. 1 DECK BOARD (w/o Rear No. 2 Seat)


    B178558
  1. Disengage the 3 clips and remove the No. 1 deck board from the rear floor board spacer.



54. REMOVE NO. 1 DECK BOARD (w/ Rear No. 2 Seat)


    B178556
  1. Disengage the 5 clips and remove the No. 1 deck board from the rear deck floor box.



55. REMOVE REAR NO. 2 SEAT INNER BELT ASSEMBLY (w/ Rear No. 2 Seat)


    B170935
  1. Remove the bolt and rear No. 2 seat inner belt assembly.

    HINT:
    Use the same procedure for the RH side and LH side.



56. DISCONNECT REAR SEAT LAP TYPE BELT ASSEMBLY LH (w/ Rear No. 2 Seat)


    B170936
  1. Remove the bolt and disconnect the rear seat lap type belt assembly LH.



57. DISCONNECT REAR SEAT LAP TYPE BELT ASSEMBLY RH (w/ Rear No. 2 Seat)

HINT:
Use the same procedure for the RH side and the LH side.



58. REMOVE REAR NO. 2 SEAT ASSEMBLY (w/ Rear No. 2 Seat)


    B205721
  1. Remove the 4 bolts and the rear No. 2 seat assembly.



59. REMOVE REAR FLOOR FINISH PLATE


    B173609
  1. Disengage the 4 clips and the 4 claws, and remove the rear floor finish plate.



60. REMOVE DECK SIDE TRIM COVER LH


    B173595E01
  1. Using a screwdriver, disengage the 2 claws and remove the deck side trim cover LH.

    HINT:
    Tape the screwdriver tip before use.



61. REMOVE DECK SIDE TRIM LH


    B173596
  1. Remove the bolt.



    B173623
  1. Disengage the 4 claws and the 3 guides, and remove the deck side trim LH as shown in the illustration.



62. REMOVE SIDE TRIM COVER LH (w/o Rear Seat Entertainment System)


    B173597
  1. Disengage the 10 claws and remove the side trim cover LH.



63. REMOVE POWER OUTLET SOCKET BEZEL (w/ Rear Seat Entertainment System)


    B173680
  1. Disengage the 4 claws.



    B173681
  1. Disconnect each connector and remove the power outlet socket bezel.



64. REMOVE REAR COMBINATION LIGHT SERVICE COVER LH


    B173611E01
  1. Using a screwdriver, disengage the 6 claws and 2 guides, and remove the rear combination light service cover LH.

    HINT:
    Tape the screwdriver tip before use.



65. REMOVE REAR POWER POINT SOCKET ASSEMBLY
  1. Disconnect the connector.



    E151327
  1. Disengage the claw and remove the rear power point socket assembly.



66. REMOVE REAR POWER OUTLET SOCKET COVER


    E151328
  1. Disengage the 2 claws and remove the rear power outlet socket cover.



67. REMOVE REAR DECK TRIM COVER (w/o Remote Folding Function)


    B173602
  1. Disengage the 10 claws and remove the rear deck trim cover.



68. REMOVE RECLINING REMOTE CONTROL LEVER BEZEL LH (w/ Remote Folding Function)


    B173603
  1. Disengage the 5 claws and remove the reclining remote control bezel LH.



69. REMOVE ROPE HOOK ASSEMBLY (for LH Side)


    B173598E01
  1. for Front Side:

    1. Using a screwdriver, disengage the 2 claws.

      HINT:
      Tape the screwdriver tip before use.

    2. Remove the bolt and the rope hook assembly.



    B173600E01
  1. for Rear Side:

    1. Using a screwdriver, disengage the 2 claws.

      HINT:
      Tape the screwdriver tip before use.

    2. Remove the bolt and rope hook assembly.



70. REMOVE NO. 2 DECK SIDE TRIM HOOK


    B173612
  1. Remove the screw and the No. 2 deck side trim hook.



71. REMOVE FRONT DECK SIDE TRIM COVER LH


    B173604E01
  1. Using a screwdriver, disengage the 4 claws and remove the 2 front deck side trim covers LH.

    HINT:
    Tape the screwdriver tip before use.



72. DISCONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY LH


    B170933
  1. Remove the bolt and disconnect the floor end of the rear No. 1 seat outer belt assembly.



73. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH
  1. Remove the 2 bolts.

  1. Remove the 2 clips.



  1. Disengage the 7 claws and 4 clips, and remove the deck trim side panel assembly LH.


    B173613



74. REMOVE QUARTER PILLAR GARNISH LH


    B175156
  1. Disengage the 2 claws and 2 guides, and remove the No. 1 seat outer belt guide.



    B173263
  1. Disengage the 2 clips and the 2 guides, and remove the quarter pillar garnish LH.



75. REMOVE ROOF SIDE INNER GARNISH ASSEMBLY LH (w/o Power Back Door)


  1. w/o Rear No. 2 Seat:



      B173268
    1. Remove the bolt.

    2. Disengage the 5 clips and 2 guides, and remove the roof side inner garnish assembly LH.



  1. w/ Rear No. 2 Seat:



      B175157
    1. Disengage the 2 claws and 2 guides, and remove the rear No. 2 seat outer belt guide.



    2. B173267
    3. Remove the bolt.

    4. Disengage the 5 clips and 2 guides, and remove the roof side inner garnish assembly LH.



76. REMOVE ROOF SIDE INNER GARNISH ASSEMBLY LH (w/ Power Back Door)


  1. w/o Rear No. 2 Seat:



      B173266
    1. Remove the bolt.

    2. Disengage the 5 clips and 2 guides, and remove the roof side inner garnish assembly LH.



  1. w/ Rear No. 2 Seat:



      B175157
    1. Disengage the 2 claws and 2 guides, and remove the rear No. 2 seat outer belt guide.



    2. B173265
    3. Remove the bolt.

    4. Disengage the 5 clips and 2 guides, and remove the roof side inner garnish assembly LH.



77. REMOVE REAR SEAT SIDE GARNISH CAP (w/o Rear Air Conditioning System)


    B173614
  1. Disengage the 8 claws and guide, and remove the rear seat side garnish cap.



78. REMOVE REAR SEAT SIDE GARNISH CAP (w/ Rear Air Conditioning System)


    B173616
  1. Remove the screw.

  1. Disengage the 6 claws and the guide, and remove the rear seat side garnish cap.



79. REMOVE DECK SIDE TRIM COVER RH

HINT:
Use the same procedure for the RH side and the LH side.



80. REMOVE DECK SIDE TRIM RH

HINT:
Use the same procedure for the RH side and the LH side.



81. REMOVE SIDE TRIM COVER RH (w/o Rear Automatic Air Conditioning System)


    B173610
  1. Disengage the 4 claws and remove the side trim cover RH.



82. REMOVE REAR ROOM TEMPERATURE SENSOR (w/ Rear Automatic Air Conditioning System)


    E150364
  1. Disengage the 4 claws and remove the rear room temperature sensor.

  1. Disconnect the connector.



83. REMOVE REAR COMBINATION LIGHT SERVICE COVER RH


    B173618E01
  1. Using a screwdriver, disengage the 6 claws and the 2 guides, and remove the rear combination light service cover RH.

    HINT:
    Tape the screwdriver tip before use.



84. REMOVE ROPE HOOK ASSEMBLY (for RH Side)

HINT:
Use the same procedure for the RH side and the LH side.



85. REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK

HINT:
Use the same procedure for the No. 1 luggage compartment trim hook and the No. 2 deck side trim hook.



86. REMOVE FRONT DECK SIDE TRIM COVER RH

HINT:
Use the same procedure for the RH side and the LH side.



87. DISCONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY RH

HINT:
Use the same procedure for the RH side and the LH side.



88. REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH
  1. Remove the 3 bolts.

  1. Remove the 2 clips.



  1. Disengage the 7 claws and 4 clips, and remove the deck trim side panel assembly RH.


    B173622



89. REMOVE QUARTER PILLAR GARNISH RH

HINT:
Use the same procedure for the RH side and the LH side.



90. REMOVE ROOF SIDE INNER GARNISH ASSEMBLY RH (w/o Rear No. 2 Seat)

HINT:
Use the same procedure for the RH side and the LH side.



91. REMOVE ROOF SIDE INNER GARNISH ASSEMBLY RH (w/ Rear No. 2 Seat)

HINT:
Use the same procedure for the RH side and the LH side.



92. REMOVE ROOF CONSOLE BOX ASSEMBLY


    B173250
  1. Using a moulding remover, disengage the 2 clips, 3 guides and fastener.

  1. Disconnect the connector and remove the roof console box assembly.



93. REMOVE VISOR BRACKET COVER (for LH Side)


    B132069
  1. Using a moulding remover, disengage the 4 claws and remove the visor bracket cover.



94. REMOVE VISOR ASSEMBLY LH


    B173261
  1. Remove the 2 screws and remove the visor assembly LH.



95. REMOVE VISOR BRACKET COVER (for RH Side)

HINT:
Use the same procedure for the RH side and the LH side.



96. REMOVE VISOR ASSEMBLY RH

HINT:
Use the same procedure for the RH side and the LH side.



97. REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)


    B175048E01
  1. Disengage the 2 claws and slide the inner rear view mirror stay holder cover as shown in the illustration.



    B175049
  1. Disengage the 2 claws and remove the inner rear view mirror stay holder cover.



98. REMOVE NO. 1 ROOM LIGHT ASSEMBLY (for Standard)


    B132140E02
  1. Using a screwdriver, disengage the 4 claws and remove the lens cover.

    HINT:
    Tape the screwdriver tip before use.



    B132142E01
  1. Using a screwdriver, disengage the 2 claws <A> as shown in the illustration.

    HINT:
    Tape the screwdriver tip before use.

  1. Disengage the 2 claws <B>.



    B153052
  1. Using a screwdriver, disengage the 4 claws and remove the No. 1 room light assembly.



99. REMOVE NO. 1 ROOM LIGHT ASSEMBLY (for Independent Type)


    B173252E01
  1. Using a screwdriver, disengage the 4 claws and remove the lens cover.

    HINT:
    Tape the screwdriver tip before use.



    B173254E01
  1. Using a screwdriver, disengage the 2 claws <A> as shown in the illustration.

    HINT:
    Tape the screwdriver tip before use.

  1. Disengage the 2 claws <B>.



    B173256
  1. Using a screwdriver, disengage the 8 claws and remove the No. 1 room light assembly.



100. REMOVE NO. 2 ROOM LIGHT ASSEMBLY


    B132140E02
  1. Using a screwdriver, disengage the 4 claws and remove the lens cover.

    HINT:
    Tape the screwdriver tip before use.



    B132142E01
  1. Using a screwdriver, disengage the 2 claws <A> as shown in the illustration.

    HINT:
    Tape the screwdriver tip before use.

  1. Disengage the 2 claws <B>.



    B153052
  1. Using a screwdriver, disengage the 4 claws and remove the No. 2 room light assembly.



101. REMOVE TELEVISION BASE (w/ Rear Seat Entertainment System)


    E150581
  1. Disengage the 4 clips and remove the television base.



102. REMOVE TELEVISION DISPLAY ASSEMBLY (w/ Rear Seat Entertainment System)
  1. Disconnect the connector.



    E150582
  1. Remove the 4 bolts.



    E150583
  1. Disengage the 2 clips and 2 claws, and then remove the television display.



103. REMOVE FRONT ASSIST GRIP SUB-ASSEMBLY (w/o Sliding Roof)


    B153056E01
  1. Using a clip remover, disengage the 4 claws.

    NOTICE:
    Do not forcibly pry the assist grip covers to prevent them from being deformed.

    HINT:
    1. Gently pry on the assist grip covers as shown in the illustration to remove them.
    2. Tape the clip remover tip before use.



    B153057
  1. Pull off the 2 assist grip covers by hand.

  1. Disengage the 2 clips and remove the front assist grip sub-assembly.

  1. Remove the 2 clips from the vehicle body.

    HINT:
    Use the same procedure for the RH side and the LH side.



104. REMOVE REAR ASSIST GRIP SUB-ASSEMBLY (w/o Sliding Roof)


    B167235E01
  1. Using a clip remover, disengage the 4 claws.

    NOTICE:
    Do not forcibly pry the assist grip covers to prevent them from being deformed.

    HINT:
    1. Gently pry on the assist grip covers as shown in the illustration to remove them.
    2. Tape the clip remover tip before use.

  1. Pull off the 2 assist grip covers by hand.



    B167236
  1. Disengage the 2 clips and remove the rear assist grip sub-assembly.

  1. Remove the 2 clips from the vehicle body.

    HINT:
    Use the same procedure for the RH side and the LH side.



105. REMOVE ASSIST GRIP ASSEMBLY (w/ Sliding Roof)


    B173257E01
  1. Using a screwdriver, disengage the 6 claws and remove the 2 assist grip covers.

    NOTICE:
    Do not forcibly pry the assist grip covers to prevent them from being deformed.

    HINT:
    Tape the screwdriver tip before use.



    B173258
  1. Disengage the 4 clips and remove the assist grip assembly.

  1. Remove the 4 clips from the vehicle body.

    HINT:
    Use the same procedure for the other 4 assist grips.



106. REMOVE ROOF HEADLINING TRIM CLIP STOPPER


    B173593E01
  1. Using a screwdriver, disengage the 3 claws.

    HINT:
    Tape the screwdriver tip before use.

  1. Remove the bolt and the roof headlining trim clip stopper.

    HINT:
    Use the same procedure for the RH side and the LH side.



107. REMOVE SUN ROOF OPENING TRIM MOULDING (w/ Sliding Roof)


108. REMOVE VISOR HOLDER


    B151362E01
  1. Turn the visor holder approximately 45° and pull it out as shown in the illustration.

  1. Disengage the 2 claws and remove the visor holder.

    HINT:
    Use the same procedure for the RH side and the LH side.



109. REMOVE ROOF HEADLINING ASSEMBLY (w/o Sliding Roof)
  1. Disconnect the No. 1 roof wire connector and disengage the 3 clamps from the front pillar LH.

  1. for Pole Antenna Type with Satellite Radio:

    1. Disconnect the No. 2 antenna cord sub-assembly connector and disengage the 2 clamps from the front pillar RH.

  1. except Pole Antenna Type without Satellite Radio:

    1. Disconnect the No. 2 antenna cord sub-assembly connector, disengage the 3 clamps and remove the bolt from the front pillar RH.

  1. for Pole Antenna Type with Satellite Radio:

    1. Disconnect the No. 2 antenna cord sub-assembly connector and disengage the clamp from the rear pillar RH.

  1. except Pole Antenna Type without Satellite Radio:

    1. Disconnect the No. 2 antenna cord sub-assembly connector from the rear pillar RH.

  1. except Pole Antenna Type with Satellite Radio:

    1. Disconnect the No. 2 antenna cord sub-assembly each connector and disengage the clamp from the rear pillar RH.



  1. Remove the 4 clips.


    B209458E01



    B173272
  1. Remove the roof headlining assembly from the vehicle through the back door.

    NOTICE:
    Do not damage the roof headlining assembly or body interior.



110. REMOVE ROOF HEADLINING ASSEMBLY (w/ Sliding Roof)
  1. Disconnect the No. 1 roof wire connectors and disengage the 3 clamps from the front pillar LH.

  1. w/ Rear Seat Entertainment System:

    1. Disconnect the No. 1 roof wire connector from the rear pillar LH.

  1. for Pole Antenna Type with Satellite Radio:

    1. Disconnect the No. 2 antenna cord sub-assembly connector and disengage the 2 clamps from the front pillar RH.

  1. except Pole Antenna Type with Satellite Radio:

    1. Disconnect the No. 2 antenna cord sub-assembly connector and disengage the 3 clamps, and remove the bolt from the front pillar RH.

  1. for Pole Antenna Type with Satellite Radio:

    1. Disconnect the No. 2 antenna cord sub-assembly connector and disengage the clamp from the rear pillar RH.

  1. except Pole Antenna Type with Satellite Radio:

    1. Disconnect the No. 2 antenna cord sub-assembly connector from the rear pillar RH.

  1. except Pole Antenna Type with Satellite Radio:

    1. Disconnect the No. 2 antenna cord sub-assembly each connector and disengage the clamp from the rear pillar RH.

  1. Disconnect the sliding roof drive gear connector.



  1. Remove the 3 clips.


    B209457E01



    B173273
  1. Remove the roof headlining assembly from the vehicle through the back door.

    NOTICE:
    Do not damage the roof headlining assembly or body interior.



111. REMOVE CURTAIN SHIELD AIRBAG ASSEMBLY
  1. Disconnect the curtain shield airbag connector.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.



  1. Remove the 11 bolts .


    C166976



  1. Disengage the 11 hooks and remove the curtain shield airbag assembly.


    C168037