AUTOMATIC TRANSAXLE SYSTEM > DATA LIST / ACTIVE TEST |
| DATA LIST |
Warm up the engine.
Turn the ignition switch off.
Connect Techstream to the DLC3.
Turn the ignition switch on (IG).
Turn on the tester.
Select the item "Powertrain / Engine and ECT / Data List".
According to the display on the tester, read the "Data List".
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Stop Light Switch | Stop light switch Status/ ON or OFF | Brake Pedal is depressed: ON Brake Pedal is released: OFF | - |
| Neutral Position SW Signal | PNP switch Status/ ON or OFF | Shift lever position is: P and N: ON Except P and N: OFF | When the shift lever position displayed on Techstream differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.
|
| Shift SW Status (P Range) | PNP switch Status/ ON or OFF | Shift lever position is: P: ON Except P: OFF | ↑ |
| Shift SW Status (N Range) | PNP switch Status/ ON or OFF | Shift lever position is: N: ON Except N: OFF | ↑ |
| Shift SW Status (R Range) | PNP switch Status/ ON or OFF | Shift lever position is: R: ON Except R: OFF | ↑ |
| Shift SW Status (D Range) | PNP switch Status/ ON or OFF | Shift lever position is: D, and S : ON Except D, and S: OFF | ↑ |
| Sports Mode Selection SW | Sport Mode Select switch Status/ ON or OFF | Shift lever position is: S, "+" and "-": ON Except S, "+" and "-": OFF | - |
| Sports Shift Up SW | Sport Shift Up switch Status/ ON or OFF | Press continuously "+" (Up shift): ON Release "+" (Up shift): OFF | - |
| Sports Shift Down SW | Sport Shift Down switch Status/ ON or OFF | Press continuously "-" (Down shift): ON Release "-" (Down shift): OFF | - |
| Shift Status | Actual Gear Position/ 1st, 2nd, 3rd, 4th or 5th | Shift Lever Position is: D: 1st, 2nd, 3rd, 4th or 5th S: 1st, 2nd, 3rd, 4th or 5th | - |
| Lock Up | Lock Up Status/ ON or OFF | Lock Up: ON Except Lock Up: OFF | - |
| Lock Up Solenoid Status | Lock Up Solenoid Status/ ON or OFF | Lock Up Solenoid: ON Except Lock Up Solenoid: OFF | - |
| SLT Solenoid Status | Shift Solenoid SLT Status/ ON or OFF | Accelerator pedal is depressed: OFF Accelerator pedal is released: ON | - |
| A/T Oil Temperature 1 | ATF Temp. Sensor Value/ min.: -40°C (-40°F) max.: 215°C (419°F) | After Stall Test: Approx. 80°C (176°F) Equal to ambient temperature when cold soak | If the value is "-40°C (-40°F)" or "215°C (419°F)", ATF temp. sensor circuit is opened or shorted. |
| SPD (NC) | Counter Gear Speed/ display: 50 r/min |
| - |
| SPD (NT) | Input Turbine Speed/display: 50 r/min |
| - |
| Snow Switch Status | Pattern SW (ECT SNOW) status/ ON or OFF | Engine switch ON: OFF ↓ Pattern switch (ECT SNOW) Push: ON ↓ Pattern switch (ECT SNOW) Push: OFF | - |
| ACTIVE TEST |
Warm up the engine.
Turn the ignition switch off.
Connect Techstream to the DLC3.
Turn the ignition switch on (IG).
Push the "ON" button of Techstream.
Select the item "Powertrain / Engine and ECT / Active Test".
According to the display on tester, perform the "Active Test".
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Control the Shift Position | [Test Details] Operate the shift solenoid valve and set each shift position by yourself. [Vehicle Condition]
| 1st/2nd/3rd/4th/5th | Possible to check the operation of the shift solenoid valves. |
| Activate the Lock Up | [Test Details] Control the shift solenoid DSL to set the automatic transaxle to the lock-up condition. [Vehicle Condition]
| ON/OFF | Possible to check the DSL operation. |
| Activate the Solenoid (SL1) | [Test Details] Operate the shift solenoid SL1 [Vehicle Condition]
| ON/OFF | - |
| Activate the Solenoid (SL2) | [Test Details] Operate the shift solenoid SL2 [Vehicle Condition]
| ON/OFF | - |
| Activate the Solenoid (SL3) | [Test Details] Operate the shift solenoid SL3 [Vehicle Condition]
| ON/OFF | - |
| Activate the Solenoid (S4) | [Test Details] Operate the shift solenoid S4 [Vehicle Condition]
| ON/OFF | - |
| Activate the Solenoid (SR) | [Test Details] Operate the shift solenoid SR [Vehicle Condition]
| ON/OFF | - |
| Activate the Solenoid (DSL) | [Test Details] Operate the shift solenoid DSL [Vehicle Condition]
| ON/OFF | - |
| Activate the Solenoid (SLT)* | [Test Details] Operate the shift solenoid SLT and raise the line pressure. [Vehicle Condition]
| ON/OFF | - |