DTC P0766 Shift Solenoid "D" Performance (Shift Solenoid Valve S4) |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0766 | The gear required by the ECM does not match the actual gear when driving (2-trip detection logic) |
|
| Related DTCs | P0766: Shift solenoid valve S4/OFF malfunction Shift solenoid valve S4/ON malfunction |
| Required sensors/Components | Shift solenoid valve S4, Speed sensor (NT), Speed sensor (NC), Crankshaft position sensor (NE) |
| Frequency of operation | Continuous |
| Duration | OFF malfunction (A) and ON malfunction (B) 1 sec. OFF malfunction (B) 1.2 sec. ON malfunction (A) 0.8 sec. |
| MIL operation | 2 driving cycles |
| Sequence of operation | None |
| The monitor will run whenever this DTC is not present. (Not circuit malfunction) | P0712, P0713 (ATF temperature sensor circuit) P0115, P0117, P0118 (ECT sensor circuit) P0717 (Turbine speed sensor circuit) P0793 (Intermediate shaft speed sensor circuit) P0500 (Vehicle speed sensor circuit) P0748 (Shift solenoid valve SL1 circuit) P0778 (Shift solenoid valve SL2 circuit) P0798 (Shift solenoid valve SL3 circuit) P0982, P0983 (Shift solenoid valve S4 circuit) P0985, P0986 (Shift solenoid valve SR circuit) P2769, P2770 (Shift solenoid valve DSL circuit) P0120, P0121, P0122, P0123, P0220, P0222, P0223, P0505, P2102, P2103, P2111, P2112, P2118, P2119, P2135 (Electronic throttle system (if applicable)) |
| ECT (Engine coolant temperature) | 10°C (50°F) or more |
| Transmission range | "D" |
| TFT (Transmission fluid temperature) | -20°C (-4°F) or more |
| ECM selected gear | 5th |
| Throttle valve opening angle | 5% or more |
| Vehicle speed | 10 km/h (6 mph) or more |
| ECM lock-up command | ON |
| ECM selected gear | 3rd, 4th or 5th |
| Throttle valve opening angle | 10% or more |
| Vehicle speed | 3rd 25 to 100 km/h (16 to 62 mph) |
| 4th, 5th 25 to 120 km/h (16 to 75 mph) |
| ECM selected gear | 4th or 5th |
| Throttle valve opening angle | 4.5% or more at engine speed 1,900 rpm (Varies with engine speed) |
| ECM selected gear | 4th |
| Throttle valve opening angle | 5% or more |
| Vehicle speed | 10 km/h (6 mph) or more |
| Intermediate shaft speed/Output speed | 1.44 to 1.58 |
| Difference between engine speed and input (turbine) speed | Less than 35 rpm |
| Input (turbine) speed/Intermediate shaft speed | 0.64 to 0.74 |
| Intermediate shaft speed/Output speed | 1.02 to 1.16 |
| PERFORM ACTIVE TEST |
Warm up the engine.
Turn the ignition switch off.
Connect Techstream to the DLC3.
Turn the ignition switch on (IG).
Turn on the tester.
Select the item "Powertrain / Engine and ECT / Active Test / Shift Status".
According to the display on the tester, perform the "Active Test".
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Control the Shift Position | [Test Details] Operate the shift solenoid valve and set each shift position by yourself. [Vehicle Condition]
| 1st/2nd/3rd/4th/5th | Possible to check the operation of the shift solenoid valves. |
| 1.CHECK OTHER DTCS OUTPUT (IN ADDITION TO DTC P0766) |
Connect Techstream to the DLC3.
Turn the ignition switch on (IG) and turn the Techstream main switch ON.
Select the item "Powertrain / Engine and ECT / Trouble Codes".
Read the DTCs using Techstream.
| Result | Proceed to |
| P0766 | A |
| P0766 and other DTCs | B |
|
| ||||
| A | |
| 2.INSPECT SHIFT SOLENOID VALVE S4 |
![]() |
Remove the shift solenoid valve S4.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Solenoid Connector (S4) - Solenoid Body (S4) | 20°C (68°F) | 11 to 15 Ω |
Connect the positive (+) lead to the terminal of the solenoid connector, and the negative (-) lead to the solenoid body.
|
| ||||
| OK | |
| 3.INSPECT TRANSMISSION VALVE BODY ASSEMBLY |
|
| ||||
| OK | |
| 4.INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY |
|
| ||||
| OK | ||
| ||