Home › STEERING › STEERING COLUMN › STEERING COLUMN ASSEMBLY

STEERING COLUMN ASSEMBLY > INSTALLATION

for Preparation Click here



1. INSTALL STEERING INTERMEDIATE SHAFT SUB-ASSEMBLY


    C166132E01
  1. Align the matchmarks on the steering intermediate shaft sub-assembly and the steering column assembly.



    C166131
  1. Install a new bolt.

    Torque:
    35 N*m{ 360 kgf*cm , 26 ft.*lbf }



2. INSTALL STEERING COLUMN ASSEMBLY


    C166135E01
  1. Check that the 2 bushings are securely installed to the steering column assembly.

    HINT:
    If the bushings are missing or damaged, replace the steering column assembly with a new one.



    C166130
  1. Install the steering column assembly with the bolt and 2 nuts.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }

  1. Connect the connectors and engage the wire harness clamps to the steering column assembly.



    C166140
  1. Connect the connector to the power steering ECU assembly.



    C166139
  1. Connect the connector to the power steering ECU assembly.

    HINT:
    As shown in the illustration, securely return the lock lever to its original position to connect the connector.



3. CONNECT STEERING INTERMEDIATE SHAFT SUB-ASSEMBLY


    C165545E01
  1. Align the matchmarks on the steering intermediate shaft sub-assembly and the power steering link assembly.



    C165544
  1. Install a new bolt.

    Torque:
    35 N*m{ 360 kgf*cm , 26 ft.*lbf }



    C166146
  1. Install the steering intermediate shaft sub-assembly to the steering column hole shield.



    C166145
  1. Tighten the bolt.



4. INSTALL NO. 1 AIR DUCT SUB-ASSEMBLY


    C166133
  1. Engage the 2 claws to install the No. 1 air duct sub-assembly.



5. POSITION FRONT WHEELS STRAIGHT AHEAD


6. INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY


    C166129
  1. Using pliers, engage the claw. Install the turn signal switch assembly with spiral cable sub-assembly to the steering column assembly.

  1. Connect the connectors to the turn signal switch assembly with spiral cable sub-assembly.



7. INSTALL STEERING COLUMN COVER


    C165716
  1. Engage the claw to install the upper steering column cover.



    C166128
  1. Engage the 2 claws to install the lower steering column cover.



    C165715
  1. Install the 2 screws.

    Torque:
    2.0 N*m{ 20 kgf*cm , 18 in.*lbf }



8. INSTALL BRAKE PEDAL SUPPORT SUB-ASSEMBLY


    C165374
  1. Install the brake pedal support sub-assembly with the 4 nuts.

    Torque:
    13 N*m{ 132 kgf*cm , 10 ft.*lbf }



    C165373
  1. Install the brake pedal support sub-assembly to the instrument panel reinforcement with the 2 bolts.

    Torque:
    35 N*m{ 357 kgf*cm , 26 ft.*lbf }



    C165371
  1. Connect the brake pedal load sensing switch connector and engage the clamp.



9. CONNECT BRAKE MASTER CYLINDER PUSH ROD CLEVIS


    C170591E01
  1. Apply lithium soap base glycol grease to the push rod pin.

  1. Connect the brake master cylinder push rod clevis to the brake pedal with the push rod pin, and install a new clip as shown in the illustration.



10. INSTALL BRAKE PEDAL RETURN SPRING


    C165369
  1. Install the brake pedal return spring between the instrument panel reinforcement and brake master cylinder push rod clevis.



11. INSTALL STOP LIGHT SWITCH ASSEMBLY


    E150075E01
  1. Temporarily install the stop light switch assembly with the stop light switch lock nut.



    E150611E01
  1. Turn the stop light switch assembly so that the clearance between the nut end and stop light switch cushion is between 0.5 to 2.4 mm (0.020 to 0.095 in.).

  1. Tighten the stop light switch lock nut.

    Torque:
    17 N*m{ 173 kgf*cm , 12 ft.*lbf }



    E150073
  1. Connect the connector.



12. INSPECT AND ADJUST BRAKE PEDAL HEIGHT


  1. Check the brake pedal height.



      C165370E01
    1. Turn back the carpet.

    2. Measure the shortest distance between the brake pedal surface and tibia pad.

      Pedal height from tibia pad:
      148.8 to 158.8 mm (5.858 to 6.252 in.)

  1. Adjust the brake pedal height.

    1. Disconnect the stop light switch connector.

    2. Remove the stop light switch assembly.

    3. Loosen the push rod clevis lock nut.

    4. Adjust the brake pedal height by turning the push rod.

    5. Tighten the push rod clevis lock nut.

      Torque:
      26 N*m{ 265 kgf*cm , 19 ft.*lbf }

    6. Install and adjust the stop light switch .

      NOTICE:
      Do not depress the brake pedal.

    7. Connect the stop light switch connector.



13. INSPECT BRAKE PEDAL FREE PLAY


    C132708E01
  1. Stop the engine. Depress the pedal several times until no vacuum is left in the brake booster. Release the brake pedal.

  1. Depress the pedal until a slight resistance is felt. Measure the distance as shown in the illustration.

    Pedal free play:
    1.0 to 6.0 mm (0.039 to 0.236 in.)

    If the pedal free play is not as specified, check the stop light switch clearance . If the pedal free play is as specified, proceed to the "INSPECT BRAKE PEDAL RESERVE DISTANCE" procedure.



14. INSPECT BRAKE PEDAL RESERVE DISTANCE

HINT:
Measure the distance at the same point used for the brake pedal height inspection.



    C111339E05
  1. Release the parking brake lever.

  1. With the engine running, depress the brake pedal and measure the pedal reserve distance as shown in the illustration.

    Pedal reserve distance from the tibia pad at 500 N (51 kgf, 112 lbf):
    84.4 mm (3.32 in.)

    If the distance is not as specified, troubleshoot the brake system (Click here).



15. INSTALL DRIVER SIDE KNEE AIRBAG ASSEMBLY
  1. Check that the ignition switch is off.

  1. Check that the battery negative (-) cable is disconnected.

    CAUTION:
    Wait for at least 90 seconds after disconnecting the cable to prevent airbag deployment.



    C165102
  1. Install the DLC3 to the driver side knee airbag assembly with the 2 claws.



    C168041
  1. Connect the driver side knee airbag connector and tire pressure warning reset switch connector to the driver side knee airbag assembly.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.



    C165100
  1. Support the driver side knee airbag assembly with one hand as shown in the illustration.



    C165099
  1. Temporarily install the driver side knee airbag assembly with the 2 hooks.



    C165098
  1. Install the driver side knee airbag assembly with the 4 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



16. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (for Manual Air Conditioning System)


    B168371
  1. Connect the hood lock control cable assembly.

  1. Connect each connector.

  1. Engage the 3 claws and 10 clips.

  1. Install the lower instrument panel finish panel sub-assembly with the 2 bolts <B>.



17. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (for Automatic Air Conditioning System)


    B173009
  1. Connect the hood lock control cable assembly.

  1. Connect each connector and the aspirator duct.



    B173021
  1. Engage the 3 claws and 10 clips.

  1. Install the lower instrument panel finish panel sub-assembly with the 2 bolts <B>.



18. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH


    B173227
  1. Engage the claw and clip, install the cowl side trim sub-assembly LH.

  1. Install the clip.



19. INSTALL FRONT DOOR SCUFF PLATE LH


    B173224
  1. Engage the guide and the 8 claws, and install the front door scuff plate LH.



20. ADJUST SPIRAL CABLE
  1. Check that the ignition switch is off.

  1. Check that the battery negative (-) cable is disconnected.

    CAUTION:
    Wait for at least 90 seconds after disconnecting the cable to prevent airbag deployment.



    C165096
  1. Rotate the spiral cable counterclockwise slowly by hand until it stops.

    NOTICE:
    Do not turn the spiral cable using the airbag wire harness.



    C165097E01
  1. Rotate the spiral cable clockwise approximately 2.5 turns to align the marks.

    NOTICE:
    Do not turn the spiral cable using the airbag wire harness.

    HINT:
    The spiral cable will rotate approximately 2.5 turns to both the left and right from the center.



21. INSTALL STEERING WHEEL ASSEMBLY


    C165708E01
  1. Align the matchmarks on the steering wheel assembly and steering main shaft.

  1. Install the steering wheel assembly set nut.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }

  1. Connect the connectors to the spiral cable sub-assembly.



22. INSPECT STEERING WHEEL CENTER POINT


23. INSTALL STEERING PAD
  1. Check that the ignition switch is off.

  1. Check that the battery negative (-) terminal is disconnected.

    CAUTION:
    Wait for at least 90 seconds after disconnecting the cable to prevent airbag deployment.



    C165092
  1. Support the steering pad with one hand as shown in the illustration.



    C165093
  1. Connect the 2 airbag connectors to the steering pad.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.

  1. Connect the horn connector to the steering pad.

  1. Confirm that the circumference groove of the "TORX" screw fits in the screw case, and place the steering pad onto the steering wheel assembly.



    C166982E01
  1. Using a "TORX" socket wrench (T30), tighten the 2 "TORX" screws.

    Torque:
    8.8 N*m{ 90 kgf*cm , 78 in.*lbf }



24. INSTALL LOWER NO. 3 STEERING WHEEL COVER


    C165090
  1. Install the lower No. 3 steering wheel cover with the claw.



25. INSTALL LOWER NO. 2 STEERING WHEEL COVER


    C165091
  1. Install the lower No. 2 steering wheel cover with the claw.



26. INSTALL FRONT WHEEL LH

Torque:
103 N*m{ 1050 kgf*cm , 76 ft.*lbf }



27. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
  1. Make sure that the cable has been disconnected from the battery terminal for at least 2 seconds before reconnecting the cable.
  2. Connect the cable to the negative (-) battery terminal with the front wheels facing straight ahead.
  3. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



28. INSPECT STEERING PAD


    C166979
  1. With the steering pad installed on the vehicle, perform a visual check. If there are any defects as mentioned below, replace the steering pad with a new one:

    1. Cuts, minute cracks or marked discoloration on the steering pad top surface or grooves.

  1. Make sure that the horn sounds.

    HINT:
    If the horn does not sound, inspect the horn system (Click here).



29. INSPECT SRS WARNING LIGHT

HINT:
(Click here)