DTC P0136 Oxygen Sensor Circuit Malfunction (Bank 1 Sensor 2) |
DTC P0137 Oxygen Sensor Circuit Low Voltage (Bank 1 Sensor 2) |
DTC P0138 Oxygen Sensor Circuit High Voltage (Bank 1 Sensor 2) |
DTC P0139 Oxygen Sensor Circuit Slow Response (Bank 1 Sensor 2) |
DTC P0156 Oxygen Sensor Circuit Malfunction (Bank 2 Sensor 2) |
DTC P0157 Oxygen Sensor Circuit Low Voltage (Bank 2 Sensor 2) |
DTC P0158 Oxygen Sensor Circuit High Voltage (Bank 2 Sensor 2) |
DTC P0159 Oxygen Sensor Circuit Slow Response (Bank 2 Sensor 2) |

| DTC No. | DTC Detection Condition | Trouble Area |
| P0136 P0156 |
|
|
| P0137 P0157 |
|
|
| P0138 P0158 |
|
|
| P0139 P0159 | Heated oxygen sensor (sensor 2) voltage does not drop to below 0.2 V immediately after fuel cut starts |
|
| DTC No. | DTC Detection Condition | Trouble Area |
| P0136 P0156 | Not applicable | None |
| P0137 P0157 |
|
|
| P0138 P0158 | Not applicable | None |
| P0139 P0159 | Not applicable | None |
| Active Air Fuel Ratio Control |
| Abnormal Voltage Output of Heated Oxygen Sensor (DTC P0136 and P0156) |

| Open or Short in Heated Oxygen Sensor Circuit (DTCs P0137 and P0157 or P0138 and P0158) |

| High or Low Impedance of Heated Oxygen Sensor (DTCs P0136 and P0156 or P0137 and P0157) |
![]() |
| Abnormal Voltage Output of Heated Oxygen Sensor During Fuel-cut (DTC P0139 and P0159) |
| Related DTCs | P0136: Heated oxygen sensor output voltage (Output voltage) (bank 1) P0136: Heated oxygen sensor impedance (Low) (bank 1) P0137: Heated oxygen sensor output voltage (Low voltage) (bank 1) P0137: Heated oxygen sensor impedance (High) (bank 1) P0138: Heated oxygen sensor output voltage (High voltage) (bank 1) P0138: Heated oxygen sensor output voltage (Extremely high) (bank 1) P0139: Heated oxygen sensor output voltage during fuel cut (bank 1) P0156: Heated oxygen sensor output voltage (Output voltage) (bank 2) P0156: Heated oxygen sensor impedance (Low) (bank 2) P0157: Heated oxygen sensor output voltage (Low voltage) (bank 2) P0157: Heated oxygen sensor impedance (High) (bank 2) P0158: Heated oxygen sensor output voltage (High voltage) (bank 2) P0158: Heated oxygen sensor output voltage (Extremely high) (bank 2) P0159: Heated oxygen sensor output voltage during fuel cut (bank 2) |
| Required Sensors/Components (Main) | Heated oxygen sensor (sensor 2) |
| Required Sensors/Components (Related) | Crankshaft position sensor Engine coolant temperature sensor Mass air flow meter Throttle position sensor |
| Frequency of Operation | Once per driving cycle: Active air fuel ratio control detection, Abnormal voltage during fuel cut Continuous: Other |
| Duration | 20 seconds: Heated oxygen sensor output (Output voltage, High voltage, Low voltage) 30 seconds: Heated oxygen sensor impedance (Low) 90 seconds: Heated oxygen sensor impedance (High) 10 seconds: Heated oxygen sensor voltage (Extremely high) 7 seconds: Heated oxygen sensor voltage during fuel cut |
| MIL Operation | 2 driving cycles |
| Sequence of Operation | None |
All:
| The monitor will run whenever these DTCs are not present | P0016, P0018 (VVT system bank 1, 2 - misalignment) P0017, P0019 (Exhaust VVT system bank 1, 2 - misalignment) P0031, P0032, P0051, P0052 (A/F sensor heater) P0037, P0038, P0057, P0058 (HO2 sensor heater) P0100, P0102, P0103 (MAF meter) P0110, P0112, P0113 (IAT sensor) P0115, P0117, P0118 (ECT sensor) P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (TP sensor) P0125 (Insufficient ECT for closed loop) P0128 (Thermostat) P0171, P0172, P0174, P0175 (Fuel system) P0301, P0302, P0303, P0304, P0305, P0306 (Misfire) P0335 (CKP sensor) P0450, P0451, P0452, P0453 (EVAP system) P0500 (Vehicle speed sensor) P2195, P2196, P2197, P2198 (A/F sensor - rationality) P2238, P2241, P2252, P2255 (A/F sensor - low impedance) P2A00, P2A03 (A/F sensor - slow response) |
| Active air fuel ratio control | Executing |
| Active air fuel ratio control begins when all of following conditions met: | - |
| Battery voltage | 11 V or more |
| Engine coolant temperature | 75°C (167°F) or more |
| Idling | OFF |
| Engine RPM | Less than 3200 rpm |
| Air fuel ratio sensor status | Activated |
| Fuel system status | Closed loop |
| Fuel cut | OFF |
| Engine load | 10 to 70% |
| Shift position | 4th or more |
| Battery voltage | 11 V or more |
| Estimated sensor temperature | Less than 700°C (1292°F) |
| ECM monitor | Completed |
| DTC P0606 | Not set |
| Battery voltage | 11 V or more |
| Estimated sensor temperature | 450°C (842°F) or higher |
| DTC P0606 | Not set |
| Battery voltage | 11 V or more |
| Time after engine start | 2 seconds or more |
| Engine coolant temperature | 75°C (167°F) or more |
| Catalyst temperature | 400°C (752°F) or more |
| Fuel cut | Executing |
| Either of following conditions met: | 1 or 2 |
| 1. All of following conditions (a), (b) and (c) met | - |
| (a) Commanded air fuel ratio | 14.3 or less |
| (b) Rear heated oxygen sensor voltage | 0.21 to 0.59 V |
| (c) Oxygen storage capacity of catalyst | 2.0 g or more |
| 2. All of following conditions (d), (e) and (f) met | - |
| (d) Commanded air fuel ratio | 14.9 or more |
| (e) Rear heated oxygen sensor voltage | 0.21 to 0.59 V |
| (f) Oxygen storage capacity | 2.0 g or more |
| All of following conditions (a), (b) and (c) met | - |
| (a) Commanded air fuel ratio | 14.3 or less |
| (b) Rear heated oxygen sensor voltage | Less than 0.21 V |
| (c) OSC (Oxygen Storage Capacity of Catalyst) | 2.0 g or more |
| All of following conditions (a), (b) and (c) met | - |
| (a) Commanded air fuel ratio | 14.9 or more |
| (b) Rear heated oxygen sensor voltage | More than 0.59 V |
| (c) Oxygen storage capacity of catalyst | 2.0 g or more |
| Duration of following condition | 30 seconds or more |
| Heated oxygen sensor impedance | Less than 5 Ω |
| Duration of following condition | 90 seconds or more |
| Heated oxygen sensor impedance | 15 kΩ or more |
| Duration of following condition | 10 seconds or more |
| Heated oxygen sensor voltage | 1.2 V or higher |
| Duration until rear heated oxygen sensor voltage drops to 0.2 V after fuel cut | 10 seconds or more |
| Duration of following condition | 30 seconds or more |
| Heated oxygen sensor voltage | Varies between 0.1 V and 0.9 V |


| Tester Display | Injection Volume | Status | Voltage |
| AFS Voltage B1 S1 or AFS Voltage B2 S1 (Air fuel ratio sensor) | +25% | Rich | Less than 3.1 V |
| -12.5% | Lean | More than 3.5 V | |
| O2S B1 S2 or O2S B2 S2 (Heated oxygen sensor) | +25% | Rich | More than 0.55 V |
| -12.5% | Lean | Less than 0.4 V |
| Case | Air Fuel Ratio Sensor (Sensor 1) Output Voltage | Heated Oxygen Sensor (Sensor 2) Output Voltage | Main Suspected Trouble Area |
| 1 | ![]() | ![]() | - |
| 2 | ![]() | ![]() |
|
| 3 | ![]() | ![]() |
|
| 4 | ![]() | ![]() |
|
| 1.READ DTC OUTPUT (DTC P0136, P0137, P0138, P0156, P0157 OR P0158) |
Connect the Techstream to the DLC3.
Turn the ignition switch on (IG).
Turn the tester on.
Select the following menu items: Powertrain / Engine and ECT / Trouble Codes.
Read DTCs.
| Result | Proceed to |
| P0138 or P0158 | A |
| P0137 or P0157 | B |
| P0136 or P0156 | C |
| P0139 or P0159 | D |
|
| ||||
|
| ||||
|
| ||||
| A | |
| 2.READ VALUE USING TECHSTREAM (OUTPUT VOLTAGE OF HEATED OXYGEN SENSOR) |
Connect the Techstream to the DLC3.
Turn the ignition switch on (IG).
Turn the tester on.
Select the following menu items: Select: Powertrain / Engine and ECT / Data List / A/F Control System / O2S B1 S2 or O2S B2 S2.
Allow the engine to idle.
Read the heated oxygen sensor output voltage while idling.
| Result | Proceed to |
| 1.0 V or more | A |
| Less than 1.0 V | B |
|
| ||||
| A | |
| 3.INSPECT HEATED OXYGEN SENSOR (CHECK FOR SHORT) |
![]() |
Disconnect the heated oxygen sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 2 (+B) - 4 (E2) | Always | 10 kΩ or higher |
| 2 (+B) - 3 (OX1B) |
| Tester Connection | Condition | Specified Condition |
| 2 (+B) - 4 (E2) | Always | 10 kΩ or higher |
| 2 (+B) - 3 (OX2B) |
Reconnect the heated oxygen sensor connector.
|
| ||||
| OK | |
| 4.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT) |
![]() |
Turn the ignition switch off and wait for 5 minutes or more.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| B1-1 (HT1B) - B1-18 (OX1B) | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| B2-5 (HT2B) - B2-33 (OX2B) | Always | 10 kΩ or higher |
Reconnect the ECM connector.
|
| ||||
| OK | ||
| ||
| 5.INSPECT AIR FUEL RATIO SENSOR |
Connect the Techstream to the DLC3.
Turn the ignition switch on (IG).
Turn the tester on.
Drive the vehicle according to the drive pattern listed below:
Warm up the engine until the engine coolant temperature reaches 75°C (167°F) or more.
Drive the vehicle at 40 mph (64 km/h) or more and decelerate the vehicle for 5 seconds or more.
Repeat the deceleration above at least 3 times.

Select the following menu items: Select: Powertrain / Engine and ECT / Monitor / O2 Sensor / Details.
Confirm that RANGE B1S1 is either PASS or FAIL. If the tester shows incomplete, re-check RANGE B1S1 after performing the drive pattern.
Select the RANGE B1S1.
Read the Test Value.
|
| ||||
|
| ||||
| 6.READ VALUE USING TECHSTREAM (OUTPUT VOLTAGE OF HEATED OXYGEN SENSOR) |
Connect the Techstream to the DLC3.
Turn the ignition switch on (IG).
Turn the tester on.
Start the engine.
Select the following menu items: Powertrain / Engine and ECT / Data List / A/F Control System / O2S B1 S2 or O2S B2 S2.
After warming up the engine, run the engine at an engine speed of 2500 rpm for 3 minutes.
Read the output voltage of the heated oxygen sensor when the engine rpm is suddenly increased.
|
| ||||
| OK | |
| 7.PERFORM ACTIVE TEST USING TECHSTREAM (INJECTION VOLUME) |
Connect the Techstream to the DLC3.
Turn the ignition switch on (IG).
Turn the tester on.
Start the engine and warm it up.
Select the following menu items: Powertrain / Engine and ECT / Active Test / Control the Injection Volume.
Change the fuel injection volume using the tester, and monitor the voltage output of air fuel ratio and heated oxygen sensors displayed on the tester.
| Tester Display | Voltage Variation | Proceed to |
| AFS Voltage B1 S1 or AFS Voltage B2 S1 (Air fuel ratio sensor) | Alternates between more and less than 3.3 V | OK |
| Remains at more than 3.3 V | NG | |
| Remains at less than 3.3 V | NG |

|
| ||||
| OK | ||
| ||
| 8.CHECK FOR EXHAUST GAS LEAK |
|
| ||||
| OK | |
| 9.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE) |
![]() |
Disconnect the heated oxygen sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 (HT1B) - 2 (+B) | 20°C (68°F) | 11 to 16 Ω |
| 1 (HT1B) - 4 (E2) | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| 1 (HT2B) - 2 (+B) | 20°C (68°F) | 11 to 16 Ω |
| 1 (HT2B) - 4 (E2) | Always | 10 kΩ or higher |
Reconnect the heated oxygen sensor connector.
|
| ||||
| OK | |
| 10.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM) |
![]() |
Disconnect the heated oxygen sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| P1-1 (HT1B) - B1-1 (HT1B) | Always | Below 1 Ω |
| P1-3 (OX1B) - B1-18 (OX1B) | ||
| P1-4 (E2) - B1-28 (E2) |
| Tester Connection | Condition | Specified Condition |
| B39-1 (HT2B) - B2-5 (HT2B) | Always | Below 1 Ω |
| B39-3 (OX2B) - B2-33 (OX2B) | ||
| B39-4 (E2) - B1-28 (E2) |
| Tester Connection | Condition | Specified Condition |
| P1-1 (HT1B) or B1-1 (HT1B) - Body ground | Always | 10 kΩ or higher |
| P1-3 (OX1B) or B1-18 (OX1B) - Body ground |
| Tester Connection | Condition | Specified Condition |
| B39-1 (HT2B) or B2-5 (HT2B) - Body ground | Always | 10 kΩ or higher |
| B39-3 (OX2B) or B2-33 (OX2B) - Body ground |
Reconnect the heated oxygen sensor connector.
Reconnect the ECM connector.
|
| ||||
| OK | |
| 11.REPLACE HEATED OXYGEN SENSOR |
Replace the heated oxygen sensor (Click here).
| NEXT | |
| 12.PERFORM CONFIRMATION DRIVING PATTERN |
| NEXT | |
| 13.CHECK WHETHER DTC OUTPUT RECURS (DTC P0136, P0137, P0138, P0156, P0157 OR P0158) |
Connect the Techstream to the DLC3.
Turn the ignition switch on (IG).
Turn the tester on.
Select the following menu items: Powertrain / Engine and ECT / Utility / All Readiness.
Input DTCs: P0136, P0137, P0138, P0156, P0157 and P0158.
Check the DTC MONITOR is NORMAL. If DTC MONITOR is INCOMPLETE, perform the drive pattern increasing the vehicle speed and using the second gear to decelerate the vehicle.
| Result | Proceed to |
| No output | A |
| P0136, P0137, P0138, P0156, P0157 or P0158 detected | B |
|
| ||||
| A | ||
| ||
| 14.REPLACE AIR FUEL RATIO SENSOR |
Replace the air fuel ratio sensor (Click here).
| NEXT | |
| 15.PERFORM CONFIRMATION DRIVING PATTERN |
| NEXT | |
| 16.CHECK WHETHER DTC OUTPUT RECURS (DTC P0136, P0137, P0138, P0156, P0157 OR P0158) |
Connect the Techstream to the DLC3.
Turn the ignition switch on (IG).
Turn the tester on.
Select the following menu items: Powertrain / Engine and ECT / Utility / All Readiness.
Input DTCs: P0136, P0137, P0138, P0156, P0157 and P0158.
Check the DTC MONITOR is NORMAL. If DTC MONITOR is INCOMPLETE, perform the drive pattern increasing the vehicle speed and using the second gear to decelerate the vehicle.
| Result | Proceed to |
| No output | A |
| P0136, P0137, P0138, P0156, P0157 or P0158 detected | B |
|
| ||||
| A | ||
| ||
| 17.READ VALUE USING TECHSTREAM (OUTPUT VOLTAGE OF HEATED OXYGEN SENSOR) |
Connect the Techstream to the DLC3.
Turn the ignition switch on (IG).
Turn the tester on.
Select the following menu items: Select: Powertrain / Engine and ECT / Data List / A/F Control System / O2S B1 S2 or O2S B2 S2.
Allow the engine to idle.
Read the heated oxygen sensor output voltage while idling.
| Result | Proceed to |
| 1.0 V or more | A |
| Less than 1.0 V | B |
|
| ||||
| A | |
| 18.INSPECT HEATED OXYGEN SENSOR (CHECK FOR SHORT) |
![]() |
Disconnect the heated oxygen sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 2 (+B) - 4 (E2) | Always | 10 kΩ or higher |
| 2 (+B) - 3 (OX1B) |
| Tester Connection | Condition | Specified Condition |
| 2 (+B) - 4 (E2) | Always | 10 kΩ or higher |
| 2 (+B) - 3 (OX2B) |
Reconnect the heated oxygen sensor connector.
|
| ||||
| OK | |
| 19.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT) |
![]() |
Turn the ignition switch off and wait for 5 minutes or more.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| B1-1 (HT1B) - B1-18 (OX1B) | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| B2-5 (HT2B) - B2-33 (OX2B) | Always | 10 kΩ or higher |
Reconnect the ECM connector.
|
| ||||
| OK | ||
| ||
| 20.READ VALUE USING DTC OUTPUT (DTC P0139 OR P0159) |
Connect the Techstream to the DLC3.
Clear the DTC (Click here).
Turn the ignition switch on (IG).
Turn the tester on.
Drive the vehicle according to the drive pattern listed below:
Warm up the engine until the engine coolant temperature reaches 75°C (167°F) or more.
Drive the vehicle at 40 mph (64 km/h) or more and decelerate the vehicle for 5 seconds or more.
Repeat the deceleration above at least 3 times.
Select the following menu items: Powertrain / Engine and ECT / Utility / All Readiness.
Input DTCs: P0139 and P0159.
Check the DTC MONITOR is NORMAL. If DTC MONITOR is INCOMPLETE, perform the drive pattern increasing the vehicle speed and using second gear to decelerate the vehicle.

| Result | Proceed to |
| No output | A |
| P0139 or P0159 detected | B |
|
| ||||
| A | ||
| ||