AIRBAG SYSTEM > SRS Warning Light Remains ON |

| 1.CHECK SRS WARNING LIGHT OPERATION |
Check the SRS warning light operation approximately 6 seconds after the ignition switch is turned on (IG).
| SRS Warning Light Illumination | Proceed to |
| Remains on | A |
| Remains on after it goes off | B |
|
| ||||
| A | |
| 2.CHECK BATTERY VOLTAGE |
Measure the voltage of the battery.
|
| ||||
| OK | |
| 3.CHECK CONNECTOR |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Check that the connector is properly connected to the center airbag sensor assembly.
Disconnect the connector from the center airbag sensor assembly.
Check that the connector terminal is not damaged.
|
| ||||
| OK | |
| 4.CHECK WIRE HARNESS (CENTER AIRBAG SENSOR ASSEMBLY - BODY GROUND) |
![]() |
Connect the negative (-) terminal cable to the battery.
Turn the ignition switch on (IG).
Operate all components of the electrical system (defogger, wipers, headlights, heater blower, etc.).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D30-21 (IG2) - Body ground | Ignition switch on (IG) | 8 to 16 V |
Turn the ignition switch off.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D30-25 (E1) - Body ground | Always | Below 1 Ω |
| D30-26 (E2) - Body ground | Always | Below 1 Ω |
|
| ||||
| OK | |
| 5.CHECK SRS WARNING LIGHT |
Turn the ignition switch on (IG).
Check the SRS warning light condition.
|
| ||||
| OK | ||
| ||
| 6.CHECK CAN COMMUNICATION SYSTEM |
Use Techstream to check if the CAN communication system is functioning normally.
| Result | Proceed to |
| DTC is not output | A |
| DTC is output | B |
|
| ||||
| A | |
| 7.CHECK BATTERY VOLTAGE |
Measure the voltage of the battery.
|
| ||||
| OK | |
| 8.CHECK CONNECTOR |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Check that the connector is properly connected to the center airbag sensor assembly.
Disconnect the connector from the center airbag sensor assembly.
Check that the connector terminal is not damaged.
|
| ||||
| OK | |
| 9.CHECK WIRE HARNESS (CENTER AIRBAG SENSOR ASSEMBLY - BODY GROUND) |
![]() |
Connect the negative (-) terminal cable to the battery.
Turn the ignition switch on (IG).
Operate all components of the electrical system (defogger, wipers, headlights, heater blower, etc.).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D30-21 (IG2) - Body ground | Ignition switch on (IG) | 8 to 16 V |
Turn the ignition switch off.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D30-25 (E1) - Body ground | Always | Below 1 Ω |
| D30-26 (E2) - Body ground | Always | Below 1 Ω |
|
| ||||
| OK | |
| 10.CHECK CONNECTOR |
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Check that the connector is properly connected to the combination meter assembly.
Disconnect the connector from the combination meter assembly.
Check that the connector terminal is not damaged.
|
| ||||
| OK | |
| 11.CHECK WIRE HARNESS (COMBINATION METER ASSEMBLY - BODY GROUND) |
![]() |
Connect the negative (-) terminal cable to the battery.
Turn the ignition switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| E1-1 (IG+) - Body ground | Always | 11 to 14 V |
| E1-21 (B) - Body ground | Ignition switch on (IG) | 11 to 14 V |
| E1-22 (B2) - Body ground | Always | 11 to 14 V |
Turn the ignition switch off.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| E1-18 (E3) - Body ground | Always | Below 1 Ω |
| E1-40 (E2) - Body ground | Always | Below 1 Ω |
|
| ||||
| OK | |
| 12.CHECK SRS WARNING LIGHT |
Connect the connector to the combination meter assembly.
Connect the negative (-) terminal cable to the battery.
Turn the ignition switch on (IG).
Check the SRS warning light condition.
|
| ||||
| OK | ||
| ||