DTC B1653/35 Seat Position Airbag Sensor Circuit Malfunction |
| DTC No. | DTC Detection Condition | Trouble Area |
| B1653/35 |
|
|

| 1.CHECK CONNECTORS |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Check that the connectors are properly connected to the center airbag sensor assembly, front seat inner belt assembly LH and the seat position airbag sensor.
Disconnect the connectors from the center airbag sensor assembly, front seat inner belt assembly LH and the seat position airbag sensor.
Check that the connector terminals are not damaged.
|
| ||||
| OK | |
| 2.CHECK FLOOR WIRE NO. 2 (OPEN) |
Connect the connectors to the front seat inner belt assembly LH and floor wire No. 2.

Using SST, connect terminals 9 (DSP+) and 17 (DSP-) of connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 2 (LSP+) - 1 (LSP-) | Always | Below 1 Ω |
|
| ||||
| OK | |
| 3.CHECK FLOOR WIRE NO. 2 (SHORT) |
![]() |
Disconnect SST from connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 2 (LSP+) - 1 (LSP-) | Always | 1 MΩ or higher |
|
| ||||
| OK | |
| 4.CHECK FLOOR WIRE NO. 2 (SHORT TO B+) |
![]() |
Connect the negative (-) terminal cable to the battery.
Turn the ignition switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 2 (LSP+) - Body ground | Ignition switch on (IG) | Below 1 V |
| 1 (LSP-) - Body ground | Ignition switch on (IG) | Below 1 V |
|
| ||||
| OK | |
| 5.CHECK FLOOR WIRE NO. 2 (SHORT TO GROUND) |
![]() |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 2 (LSP+) - Body ground | Always | 1 MΩ or higher |
| 1 (LSP-) - Body ground | Always | 1 MΩ or higher |
|
| ||||
| OK | |
| 6.CHECK SEAT POSITION AIRBAG SENSOR |
![]() |
Connect the connectors to the center airbag sensor assembly and the seat position airbag sensor.
Connect the negative (-) terminal cable to the battery.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Check for DTCs (Click here).
|
| ||||
| OK | ||
| ||
| 7.REPLACE SEAT POSITION AIRBAG SENSOR |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Replace the seat position airbag sensor (Click here).
| NEXT | |
| 8.CHECK CENTER AIRBAG SENSOR ASSEMBLY |
![]() |
Connect the negative (-) terminal cable to the battery.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Check for DTCs (Click here).
|
| ||||
| OK | ||
| ||
| 9.CHECK FLOOR WIRE NO. 2 (OPEN) |
Disconnect the floor wire No. 2 from front seat inner belt assembly LH.

Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| O10-2 (LSP+) - O10-4 (LSP-) | Always | Below 1 Ω |
|
| ||||
| OK | ||
| ||
| 10.CHECK FLOOR WIRE NO. 2 (SHORT) |
![]() |
Disconnect the floor wire No. 2 from front seat belt inner belt assembly LH.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| O10-2 (LSP+) - O10-4 (LSP-) | Always | 1 MΩ or higher |
|
| ||||
| OK | ||
| ||
| 11.CHECK FLOOR WIRE NO. 2 (SHORT TO B+) |
![]() |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Disconnect the floor wire No. 2 from front seat inner belt assembly LH.
Connect the negative (-) terminal cable to the battery.
Turn the ignition switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| O10-2 (LSP+) - Body ground | Ignition switch on (IG) | Below 1 V |
| O10-4 (LSP-) - Body ground | Ignition switch on (IG) | Below 1 V |
|
| ||||
| OK | ||
| ||
| 12.CHECK FLOOR WIRE NO. 2 (SHORT TO GROUND) |
![]() |
Disconnect the floor wire No. 2 from front seat inner belt assembly LH.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| O10-2 (LSP+) - Body ground | Always | 1 MΩ or higher |
| O10-4 (LSP-) - Body ground | Always | 1 MΩ or higher |
|
| ||||
| OK | ||
| ||