Home › SUSPENSION & AXLE › SUSPENSION › FRONT SHOCK ABSORBER

FRONT SHOCK ABSORBER > INSTALLATION

for Preparation Click here



1. SECURE FRONT SHOCK ABSORBER ASSEMBLY


    C166280E01
  1. As shown in the illustration, secure the front shock absorber with coil spring in a vise using aluminum plates by clamping onto a double nutted bolt affixed to the bracket at the bottom of the absorber.



2. INSTALL FRONT COIL SPRING LOWER INSULATOR


    C165910E01
  1. Install the front coil spring lower insulator to the front shock absorber.

    NOTICE:
    Make sure that the positioning pins on the front coil spring lower insulator are inserted into the holes in the front shock absorber.



3. INSTALL FRONT SPRING BUMPER


    C165909
  1. Install the front spring bumper to the front shock absorber.



4. INSTALL FRONT COIL SPRING


    C104393E01
  1. Using SST, compress the front coil spring.

    SST
    09727-30021   (09727-00010, 09727-00031)
    09727-00050  

    NOTICE:
    Do not use an impact wrench. It will damage the SST.

    HINT:
    If the front coil spring is compressed at an angle, using 2 SST will make the work easier.



    C149503E01
  1. Install the front coil spring to the front shock absorber.

    NOTICE:
    Make sure that the end of the front coil spring is positioned in the depression of the lower spring seat.



5. INSTALL FRONT COIL SPRING UPPER INSULATOR


    C144863E02
  1. Install the front coil spring upper insulator as shown in the illustration.

    HINT:
    Any misalignment between the front shock absorber lower bracket and the alignment mark must be +/- 5°.



6. INSTALL FRONT COIL SPRING UPPER SEAT


    C143786E02
  1. Install the front coil spring upper seat with the mark facing to the outside of the vehicle.

    HINT:
    Any misalignment between the front shock absorber lower bracket and the alignment mark must be +/- 5°.



7. INSTALL FRONT SUSPENSION SUPPORT BEARING


    F040162E03
  1. Install the front suspension support bearing as shown in the illustration.



8. INSTALL FRONT SUSPENSION SUPPORT SUB-ASSEMBLY


    C144864E02
  1. Install the front suspension support sub-assembly as shown in the illustration.

    HINT:
    Check that the slot on the piston rod and the slot on the front suspension support sub-assembly are aligned.

  1. Temporarily tighten a new front support to front shock absorber nut.



9. INSTALL FRONT SHOCK ABSORBER WITH COIL SPRING


    C165912
  1. Install the front shock absorber with coil spring (upper side) with the nut and 2 spacers.

    Torque:
    85 N*m{ 866 kgf*cm , 63 ft.*lbf }



    C165908
  1. Install the front shock absorber with coil spring (lower side) to the steering knuckle and insert the 2 bolts and 2 nuts.

    Torque:
    290 N*m{ 2956 kgf*cm , 214 ft.*lbf }

    NOTICE:
    When installing the nuts, keep the bolts from rotating.



10. INSTALL FRONT STABILIZER LINK ASSEMBLY


    C165915
  1. Install the front stabilizer link assembly to the front shock absorber with the nut.

    Torque:
    74 N*m{ 755 kgf*cm , 55 ft.*lbf }

    NOTICE:
    If the ball joint turns together with the nut, use a hexagon wrench (6 mm) to hold the stud bolt.



11. INSTALL FRONT SPEED SENSOR


    C167708
  1. Install the front speed sensor and front flexible hose with the bolt.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }

    NOTICE:
    Do not twist the front speed sensor when installing it.

  1. Install the clamp.



12. INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY


    C165926E01
  1. Install the outer cowl top panel sub-assembly with the 8 bolts and 6 nuts.

    Torque:
    Nut A:
    85 N*m{ 866 kgf*cm , 63 ft.*lbf }
    Bolt B:
    8.8 N*m{ 90 kgf*cm , 78 in.*lbf }
    Nut C:
    8.8 N*m{ 90 kgf*cm , 78 in.*lbf }



    C165925
  1. Engage the 4 clamps.



13. FULLY TIGHTEN FRONT SUPPORT TO FRONT SHOCK ABSORBER NUT


    C165911
  1. Fully tighten the front support to front shock absorber nut.

    Torque:
    70 N*m{ 714 kgf*cm , 52 ft.*lbf }



14. INSTALL WINDSHIELD WIPER MOTOR AND LINK


    E150150
  1. Install the windshield wiper motor and link assembly with the 4 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

  1. Connect the connector.



15. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY


  1. Engage the 20 claws.


    E150149

  1. Install the cowl top ventilator louver sub-assembly with the 2 clips.



    E150146
  1. Engage the 2 claws and connect the front fender to cowl side seal LH.



    E150147
  1. Engage the 2 claws and connect the front fender to cowl side seal RH.



16. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH
  1. Operate the wiper and stop the windshield wiper motor at the automatic stop position.



  1. When reinstalling:



      E112237E01
    1. Clean the wiper arm serrations.

    2. Clean the wiper pivot serrations with a wire brush.



    E147125E01
  1. Install the front wiper arm and blade assembly RH with the nut to the position shown in the illustration.

    Torque:
    24 N*m{ 245 kgf*cm , 18 ft.*lbf }

    HINT:
    Hold the wiper arm by hand when tightening the nut.

    Area
    Measurement
    A
    25.6 mm (1.00 in.)



17. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH
  1. Operate the wiper and stop the windshield wiper motor at the automatic stop position.



  1. When reinstalling:



      E112237E01
    1. Clean the wiper arm serrations.

    2. Clean the wiper pivot serrations with a wire brush.



    E152618E01
  1. Install the front wiper arm and blade assembly LH with the nut to the position shown in the illustration.

    Torque:
    24 N*m{ 245 kgf*cm , 18 ft.*lbf }

    HINT:
    Hold the wiper arm by hand when tightening the nut.

    Area
    Measurement
    A
    31.9 mm (1.26 in.)

  1. Operate the front wipers while spraying washer fluid onto the windshield glass. Make sure that the front wipers function properly and the wipers do not come into contact with the vehicle body.



18. INSTALL FRONT WHEEL

Torque:
103 N*m{ 1050 kgf*cm , 76 ft.*lbf }



19. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT
Inspect and adjust front wheel alignment (Click here).