FRONT WHEEL ALIGNMENT > ADJUSTMENT |
| 1. INSPECT TIRES |
Inspect the tires (Click here).
| 2. MEASURE VEHICLE HEIGHT |
Bounce on the vehicle up and down at the corners to stabilize the suspension.
![]() |
Measure the vehicle height.
| Model | Front A - B | Rear C - D |
| 2WD | 118.2 mm (4.65 in.) | 34.9 mm (1.37 in.) |
| 4WD | 118.3 mm (4.66 in.) | 33.8 mm (1.33 in.) |
| 3. INSPECT WHEEL ANGLE |
Put tread center marks on the rearmost points of the turning radius gauge.
![]() |
Turn the steering wheel to the left and right full lock positions, and measure the turning angle.
| Model | Inside wheel | Outside wheel Reference |
| 2WD | 35°07' +/- 2° (35.12° +/- 2°) | 31°20' (31.33°) |
| 4WD | 35°07' +/- 2° (35.12° +/- 2°) | 31°20' (31.33°) |
| 4. INSPECT CAMBER, CASTER AND STEERING AXIS INCLINATION |
![]() |
Install the camber-caster-kingpin gauge or place the front wheels on the center of the wheel alignment tester.
Inspect the camber, caster and steering axis inclination.
| 2WD | 4WD | Right-left difference | |
| Camber Inclination | -0°38' +/- 45' (-0.63° +/- 0.75°) | -0°38' +/- 45' (-0.63° +/- 0.75°) | 45' (0.75°) or less |
| Caster Inclination | 2°37' +/- 45' (2.62° +/- 0.75°) | 2°37' +/- 45' (2.62° +/- 0.75°) | |
| Steering Axis Inclination | 11°01' +/- 45' (11.02° +/- 0.75°) | 11°01' +/- 45' (11.02° +/- 0.75°) |
| 5. ADJUST CAMBER |
Remove the front wheel.
![]() |
Remove the 2 nuts on the lower side of the front shock absorber.
Clean the installation surfaces of the front shock absorber and the steering knuckle.
Temporarily install the 2 nuts (Step A).
![]() |
Fully push or pull the front axle hub in the direction of the required adjustment (Step B).
Tighten the nuts.
Install the front wheel.
![]() ![]() ![]() |
Check the camber.
If the measured value is not within the specification, calculate the required adjustment amount using the formula below.
Camber adjustment amount = center value of the specified range - measured value.
Check the combination of installed bolts. Select appropriate bolts from the table below to adjust the camber to the specified values.
| Move the axle toward (+) in step (B) | Move the axle toward (-) in step (B) |
| Refer to table (1) (Move the axle toward positive side) | Refer to table (2) (Move the axle toward negative side) |
Repeat the steps mentioned above. In step (A), replace 1 or 2 selected bolts.
| 6. INSPECT TOE-IN |
Bounce the vehicle up and down at the corners to stabilize the suspension.
Release the parking brake and move the shift lever to the neutral position.
Push the vehicle straight ahead approximately 5 m (16.4 ft.). (*1)
![]() |
Put tread center marks on the rearmost points of the front wheels and measure the distance between the marks (dimension B).
Slowly push the vehicle straight ahead to cause the front wheels to rotate 180° using the front tire valve as a reference point.
![]() |
Measure the distance between the tread center marks on the front side of the wheels (dimension A).
| Item | Specified Condition |
| Toe-in (total) | C + D: 0°02' +/- 12' (0.04° +/- 0.2°) B - A: 0.9 +/- 2 mm (0.04 +/- 0.08 in.) |
| 7. ADJUST TOE-IN |
![]() |
Make sure that the lengths of the right and left rack ends are almost the same.
Remove the rack boot set clips.
![]() |
Loosen the tie rod end lock nuts.
Adjust the rack ends if the difference in thread length between the right and left rack ends is not within the specified range.
Extend the shorter rack end if the measured toe-in deviates toward the outer-side.
Shorten the longer rack end if the measured toe-in deviates toward the inner-side.
Turn the right and left rack ends by an equal amount to adjust the toe-in to the center value.
Make sure that the lengths of the right and left rack ends are the same.
Tighten the tie rod end lock nuts.
Place the boots on the seats and install the clips.
| 8. PLACE FRONT WHEELS FACING STRAIGHT AHEAD |
| 9. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 10. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 11. PERFORM YAW RATE SENSOR ZERO POINT CALIBRATION |
| 12. CHECK STEERING ANGLE SENSOR ZERO POINT CALIBRATION |