Home › BODY ELECTRICAL › DOOR LOCK › FRONT DOOR LOCK

FRONT DOOR LOCK > INSTALLATION

for Preparation Click here



1. INSTALL FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY


    B172963
  1. Install the front door inside locking cable assembly.



    B172962
  1. Engage the 3 claws.



2. INSTALL FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY


    B172961
  1. Install the front door lock remote control cable assembly.



3. INSTALL FRONT DOOR LOCK ASSEMBLY

NOTICE:
  1. When reusing the removed front door lock assembly, replace the door lock wiring harness seal on the connector with a new one.
  2. Do not allow grease or dust to adhere to the door lock wiring harness seal surface of the connector.
  3. Reusing the door lock wiring harness seal or using a damaged door lock wiring harness seal may cause water intrusion to the connection. This may result in a malfunction of the front door lock assembly.

  1. Apply MP grease to the sliding parts of the front door lock assembly.

  1. Install a new door lock wiring harness seal to the front door lock assembly.



    B172960
  1. Insert the front door lock open rod to the front door lock assembly.

  1. Make sure that the front door lock open rod is securely connected to the front door lock assembly.

  1. Using a "TORX" socket wrench (T30), install the front door lock assembly with the 3 screws.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }



4. INSTALL FRONT DOOR OUTSIDE HANDLE COVER (for Driver Side)


    B172951
  1. Engage the 2 claws to install the front door outside handle cover to the front door lock cylinder.



    B172971
  1. Install the front door lock cylinder.

    HINT:
    Make sure that the front door lock cylinder rod is inserted into the front door lock assembly.



    B172949
  1. Using a "TORX" socket wrench (T30), install the front door lock cylinder with the screw.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }

  1. Install the hole plug.



5. INSTALL FRONT DOOR OUTSIDE HANDLE COVER (for Front Passenger Side)


    B172952
  1. Using a "TORX" socket wrench (T30), install the front door lock cylinder with the screw.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }

  1. Install the hole plug.



6. INSTALL FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY


    B174204
  1. Install the front door rear lower frame sub-assembly with the bolt.



7. INSTALL FRONT DOOR GLASS RUN


    B172946
  1. Install the front door glass run.



8. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY


    B172972E01
  1. Insert the front door glass sub-assembly into the front door panel along the front door glass run as indicated in the order of the arrows in the illustration.



    B172941
  1. Install the front door glass sub-assembly with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



    B172940
  1. Install the hole plug.



9. INSTALL FRONT DOOR SERVICE HOLE COVER
  1. Apply butyl tape to the front door panel.

  1. Pass the front door lock remote control cable and rear door inside the locking cable through a new front door service hole cover.



    B172973E01
  1. Attach the front door service hole cover according to the reference points on the front door panel.

    NOTICE:
    Securely install the front door service hole cover avoiding wrinkles and air bubbles.



    B172939
  1. Connect each connector.

  1. Engage the 2 clamps.



10. INSTALL FRONT DOOR INNER GLASS WEATHERSTRIP


    B172936
  1. Engage the 2 claws.

  1. Install the 2 screws and install the front door inside handle sub-assembly.



11. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY
  1. Connect the connector.



    B172935
  1. Connect the front door lock remote control cable and front door inside locking cable to the front door inside handle sub-assembly.

  1. Engage the 2 clamps.



    B172933
  1. Engage the front door trim board with the 5 claws on the front door inner glass weatherstrip.

  1. Engage the 9 clips.



    B172932E01
  1. Install the 2 screws <B>.

  1. Install the screw <A> and front door trim board to the front door panel.

    Torque:
    3.5 N*m{ 36 kgf*cm , 31 in.*lbf }



12. INSTALL COURTESY LIGHT ASSEMBLY
  1. Connect the connector.



    B172930
  1. Engage the claw and install the courtesy light assembly.



13. INSTALL ASSIST GRIP COVER


    B172925
  1. Engage the 4 claws and install the assist grip cover.



14. INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG


    B172921
  1. Engage the 3 claws and install the front door inside handle bezel plug.



15. INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH


    B172931
  1. Engage the clip and claw, and install the front door lower frame bracket garnish.



16. CONNECT NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).